General Information ........................5 Classification/Regulations ......................5 Guarantee ............................ 5 SAFETY INFORMATION DESCRIPTION Description of the NOCOSPRAY 2 ....................8 Overall dimensions ........................8 Positioning of the device ......................9 Installation of the bottle ......................9 Operation in standard mode ....................10 4.3.1...
Page 4
History display ..........................21 5.3.1 Screen description ......................21 5.3.2 Modification of general settings ..................22 5.3.3 Export the history in PDF format ..................22 5.3.4 Exit USB mode ........................23 ANNEXES Duration of diffusion and consumption .................24 Maintenance ..........................25 Technical characteristics ......................25 EMC compliance table ......................26 RECYCLING...
The device must be stored in a dry location and transported in its original packaging. Guarantee Duration The NOCOSPRAY 2 diffuser is guaranteed for a period of 2 years, effective as of the date of the invoice.
2. SAFETY INFORMATION The manufacturer may in no case be held responsible for any incident caused physically or to the hardware by faulty or abnormal use of the device which is contrary to the recommended instructions in the following non- exhaustive list: To avoid all risks of electrical shock, the device must imperatively be connected to an electrical supply network equipped with a protective grounding.
Page 7
The device diffuses a chemical substance. Due to this, the following recommendations must imperatively be respected: Users are required to read the accompanying documents. The device must be used solely indoors. Do not inhale the product. Do not smoke in proximity to the device Do not direct the device towards an incandescent area.
3. DESCRIPTION Description of the NOCOSPRAY 2 Handle Diffuser release button Diffuser nose (venturi) Jet and support jet Bottle Control keypad Power switch Fuses Power cable plug Mini-USB Port Overall dimensions 494 mm...
The installation of the bottle is carried out in the manner below. Consider dating the product bottle before installing it onto the NOCOSPRAY 2. Always check that the bottle contains a sufficient amount of product for the desired treatment (the device does not indicate this).
Use without remote control Steps Action Illustration Plug in the NOCOSPRAY 2 power cable. Set the power switch to “1”. Select the volume to be treated by sliding your finger over the pale part of the keypad (*). The selection range is between 10 m...
The remote control allows the device to be launched from outside of the room. 4.3.2.1 Initial pairing with the remote control Before using the remote control for the first time, it needs to be paired with the NOCOSPRAY 2 device. Follow the steps below: Steps...
Ensure that all NOCOSPRAY 2 devices in proximity to the remote control are switched off. Switches set to “0”. Plug in the power cable of the new NOCOSPRAY 2 to be paired. Set the power switch to “0”. Press and hold the button on the remote control (approx. 30 seconds directly next to the NOCOSPRAY 2 to be paired.
Illustration Once the LED of the remote control blinks regularly and without stopping, turn on the NOCOSPRAY 2 to be paired using its power switch whilst holding down the button on the remote control. The LED on the remote control will begin to blink rapidly.
Respect the safety information provided on page 7. Operation in programmer mode 4.4.1 Modus operandi It is possible to use the NOCOSPRAY 2 with a programmer (not provided) in order to differ or repeat treatments. Follow the procedure outlined below to select the programmer mode. Steps Action Illustration Plug in the NOCOSPRAY 2 power cable.
Page 15
1000 m The selected volume is displayed only when you touch the keypad. Set the power switch to “0”. Connect the NOCOSPRAY 2 to the programmer. Plug the programmer into a mains socket. Refer to the programmer’s notice to program it.
Steps Action Illustration The programmer will launch and stop the NOCOSPRAY 2 according to the performed programming. A beep will sound for 15 seconds before the machine begins to function. Leave the room before the end of the 15 seconds. AT the end of diffusion, a beep will sound.
4.4.3 Return to standard mode Steps Action Illustration To exit programmer mode and return to standard mode: Turn your finger in a clockwise direction on the pale part of the keypad up to the indication 10, then carry out at least supplementary rotations.
5. TRACKING SYSTEM The tracking system records the 125 latest treatments performed by the NOCOSPRAY 2. The 126 treatment erases and replaces the 1 and so forth. Software installation • Insert the CD Rom or the USB key provided into your PRC and open the folder named “Nocospray Tracker”.
Page 19
Steps Action Illustration Click “Finish”. If the following window appears, click “Close”. The icon opposite may be displayed to indicate that the peripheral driver has been correctly installed. The software "NocosprayTracker" is launched automatically after installation. If your computer does not allow automatic installation, seek advice from your IT manager.
History transfer Steps Action Illustration Plug the USB cable into the back of the NOCOSPRAY 2 and into the USB Port of your computer (*). During data transfer: • the LEDs 10 and 1000 blink, • the LED 250 is illuminated.
Open the software "NocosprayTracker" (in the programmes on your computer). The screen below shows an example of a history. Each line of the table represented a treatment. Note: The indication in the lower left, “Connected to COM4”, indicates that the NOCOSPRAY 2 is connected. 9 10...
5.3.2 Modification of general settings Steps Action Illustration To modify the general settings, click on the icon at the bottom of the screen. The following window will be opened: This window allows the modification of the device name and the date and time of the device. Proceed to modifications.
5.3.4 Exit USB mode Steps Action Illustration To exit USB mode, you simply have to: • Unplug the USB cable from the computer and the device (*) • Close the software. (*) No treatment may be performed whilst the USB cable is plugged in.
Maintenance Before any intervention, ensure that the device is switched off and unplug the mains cable. Do not use abrasive products, bleach, acetone or solvents during maintenance or disinfection operations for the device. These aggressive agents risk damaging the device's surface materials. To clean the external surfaces, use a slightly moist cloth or wipe.
Voltage/Flicker test IEC 61000-3-3 The NOCOSPRAY 2 is intended for use in the electromagnetic environment specified below. The customer or the user of the NOCOSPRAY 2 should assure that it is used in such an environment. Electromagnetic environment Immunity test...
Page 27
Recommended separation distances between portable and mobile RF communications equipment and the NOCOSPRAY 2. The NOCOSPRAY 2 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the NOCOSPRAY 2 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF The NOCOSPRAY 2 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
7. RECYCLING IMPORTANT INFORMATION FOR DISPOSAL IN RESPECT OF THE ENVIRONMENT This product is subject to selective sorting for electrical and electronic equipment in compliance with the 2002/96/CE Directive (applicable in member countries of the European Union and other European countries with selective sorting systems.
Page 30
OXY’PHARM 829 rue Marcel Paul – ZA des Grands Godets F-94500 Champigny sur Marne Tel. +33 145 187 870 +33 148 824 613 E-mail commercial@oxypharm.net www.oxypharm.net...
Need help?
Do you have a question about the NOCOSPRAY 2 and is the answer not in the manual?
Questions and answers