Summary of Contents for Middle Atlantic Products L7 Series
Page 1
Series Electric Lift Lectern THANK YOU Thank you for purchasing the L7 Series electric lift lectern. Please read these instructions thoroughly before installing or assembling this product. PRODUCT FEATURES • Middle Atlantic 8 outlet, 15 amp power strip with surge and circuit breaker.
GROUNDING INSTRUCTIONS / INSTRUCTIONS DE MISE À LA TERRE This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.
Page 4
IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ CAUTION! To avoid an unstable condition, place heavier WARNING/CAUTION! The exclamation point within an components at the bottom of the cabinet. When more than equilateral triangle is intended to alert the user to the one component is placed in the cabinet, begin at the presence of important operating and maintenance bottom of the cabinet and place equipment at the lowest...
IMPORTANT SAFETY INSTRUCTIONS When using an electrical furnishing, basic precautions should always be followed, including the following: • For institutional use. • Read and follow all instructions before using. • WARNING – Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on the child.
Page 6
INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ Lorsque vous utilisez des mobiliers électriques, toujours respecter les précautions de base, notamment: • Usage institutionnel. • Lire et suivre toutes les instructions avant l'utilisation du matériel. • AVERTISSEMENT - Des blessures graves ou mortelles peuvent survenir si un enfant grimpe sur le meuble d'un équipement audio ou vidéo.
WEIGHT RATINGS Item Weight Rating Work Surface 150 lbs. (68 kg) Maximum Total Rated Load Rack Enclosure 75 lbs. (34 kg) Maximum Total Rated Load Drawer(s) 15 lbs. (6.8 kg) Maximum Total Rated Load Monitor Mount 19.8 lbs. (9 kg) Maximum Total Rated Load WARNING: This product is intended for use only with the products and maximum weights indicated.
Page 8
SUPPLIED COMPONENTS AND HARDWARE (CONTINUED) NOTE: One of the following 3 top options was purchased with your lectern. 10” CUTOUT TURRET OPTION (L7-TUR-C1060) (2x) 8-32 Nut (4x) Extra Trim Ring Screw 10” (254mm)Turret 7” CUTOUT TURRET OPTION (L7-TUR-C760) (4x) Extra Trim Ring (2x) 8-32 Nut Screw 7”...
REQUIRED TOOLS • Protective Eyewear WARNING: Use tools with caution and follow all necessary safety • Power Driver protocols. • ½” Drill Bit AVERTISSEMENT: Utiliser des outils avec prudence et suivre • #2 Phillips Screwdriver tous les protocoles de sécurité nécessaires. •...
WORK SURFACE REMOVAL NOTE: The document camera drawer and/or storage drawer (preinstalled, if purchased) should be taken out before removing the work surface. If you don’t have a camera drawer and/or storage Press in levers inside of tracks on drawer, proceed to step 3. both sides of the drawer to release.
Page 11
WORK SURFACE REMOVAL (CONTINUED) 4. Slide work surface forward and lift off frame. (FIGURE E) NOTE: To prevent damage to wood surface, lay work surface flat onto a blanket or padded surface. Do not stand on end. FIGURE E 5. Remove (8x) trim ring screws as shown. (FIGURE F) NOTE: Place screws and trim ring in a safe location as they will be required when reassembling the lectern.
WORK SURFACE REMOVAL (CONTINUED) 6. Lift connectivity panel out of the lectern to expose connection wires and cable tray for cable management. (FIGURE G) Connectivity Panel FIGURE G INSTALLING THE CRESTRON® PANEL INTO TURRET OPTION (IF APPLICABLE) 1. If one of the turret options has been purchased, use (2x) 8-32 nuts and the instructions and additional hardware provided with your Crestron®...
CABLE MANAGEMENT NOTE: Before routing any cables or wires, plug the lectern power cable into an outlet and raise the unit to its maximum height as shown. (FIGURE J) NOTE: To avoid cables or wires being pulled, raise the unit to its maximum height before routing any cables.
Page 14
CABLE MANAGEMENT (CONTINUED) 2. Cable access points are provided on each leg to allow wires to be snaked down the legs and out the cable grommets on each leg. (FIGURE K) 3. Create service loops with the cables and secure with supplied hook and loop straps and wire ties as needed.
CABLE MANAGEMENT (CONTINUED) 4. Lay the connectivity panel and turret option (if purchased) on their sides and complete the wiring of all devices in the connectivity panel and any customer supplied Crestron units. (FIGURE L) NOTE: • Refer to instructions provided with your Crestron panel to wire the unit properly. •...
INSTALLING THE MONITOR MOUNT OPTION (CONTINUED) NOTE: On underside of modesty panel assembly, there are 3 monitor mount and 4 grommet pilot holes provided. 2. Use a power driver and a ½” drill bit to drill a thru-hole in desired location (left, middle, or right) for the monitor mount cup.
INSTALLING THE GROMMET (OPTIONAL, CONTINUED) 3. Separate the top from the grommet Grommet and place the grommet into the hole as shown. (FIGURE S) Grommet FIGURE S 4. Save the grommet top to install as shown, if desired, after completing the rest of the topics in this instruction sheet and running any cabling through the grommet as needed.
REASSEMBLING THE LECTERN 1. Reposition the connectiviity panel on the cable tray as shown. (FIGURE V) 2. Depending on the option purchased with your lectern, position the turret or storage tray on the cable tray. Storage Tray Turret Connectivity Panel Cable Tray FIGURE V NOTE: Verify the torque on your power driver is on the lightest setting and only increase as necessary.
Page 19
REASSEMBLING THE LECTERN (CONTINUED) NOTE: Use steps 4, 5, and 6 to make sure all gaps are spaced appropriately before tightening the trim ring screws. NOTE: 4. Maintain gap between the • Top view of lectern shown for clarity. • Gap on hinged side of tray door on connectivity panel or storage tray connectivity panel’s tray doors and is slightly larger.
Page 20
REASSEMBLING THE LECTERN (CONTINUED) Use (6x) 10-32 x 2-¾” pan head screws and (2x) 10-32 x ¾” truss head screws through frame and into the modesty panel from the underside of the lectern as shown. (FIGURE Z) (6x) Pan Head Screws NOTE: Back of lectern shown on angle for clarity.
REASSEMBLING THE LECTERN (CONTINUED) 11. Reinstall and tighten (2x) work surface screws (removed during disassembly) from the underside of the lectern as shown. (FIGURE AB) Work Surface Screws FIGURE AB INSTALLING THE LOWER PRIVACY PANEL NOTE: • Use care when positioning lower privacy panel and do not move Back Brackets lectern around as the panel is...
INSTALLING THE UPPER PRIVACY PANEL 1. With spring pin on top, hook (4x) panel support pins into (4x) slots on the rear of the lectern in locations as shown. (FIGURE AD) Spring Pin Panel Support Slot FIGURE AD 2. Carefully use top handle to l ift panel straight up until you hear the spring pin lock into place . (FIGURE AE) TIP: Use your knee or side to hold the panel in place while lifting, if necessary.
ADJUSTING THE LEVELING FEET • To level the lectern and/or prevent it from rolling, loosen the leveling foot on each corner down to the desired height as shown . (FIGURE AF) Leveling Foot FIGURE AF THERMAL MANAGEMENT 1. Install the jumper on the inline fan controller for one of the following functions: Jumper •...
THERMAL MANAGEMENT (CONTINUED) 2. Use hook and loop adhesive to secure the fan controller to upper portion of the rack opening as shown. (FIGURE AH) NOTE: For best operation, install the fan controller at the highest point above equipment installed in the rack.
REMOVING THE PRIVACY PANELS FOR RACK ACCESS 1. While carefully holding the upper privacy panel by the spring pin bracket, p ull the spring pin back and turn the hook so it rests on the bracket as shown. (FIGURE AL) 2.
Voice: 613-836-2501 - Fax: 613-836-2690 / ca.middleatlantic.com - customerservicecanada@middleatlantic.ca Factory Distribution USA: NJ - CA - IL Canada: ON At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company. Page 26...