Table of Contents
Advertisement
Screen
2 Setup input
EMU4-HM1-MB, EMU4-PX4
（
2-1.
（1） In 2-1, Push the ▲ or ▼ key , and move the cursor to the "1 Input".
[I/O]
（2） Push the
1
Input
（3） 2-2 will be displayed.
2 OP.Time
3 Output
2-2.
（1） Push the ＋ or － key , and select the input method. (Non/ Contact /Pulse)
[Input]
（2） Push the
Non
（3） Transition to the following screen by the model and setting input method.
[Non] setting
[N]
Model：EMU4-HM1-MB → To 2-1
Model：EMU4-PX4 → The [N] changes, and screen turned to setting of next CH.
EMU4-PX4 only
[Pulse] setting → To 2-3
[Contact] setting → To 2-4
2-3.
（1） Push the ▲
[CONV.Rate]
（2） Push the
1.000
（3） Transition to the following screen by the model.
[Unit]
Model：EMU4-HM1-MB → To 2-1
Non
[N]
Model：EMU4-PX4 → To 2-2 (The [N] changes, and screen turned to setting of next CH.)
EMU4-PX4 only
2-4.
（1） Push the ＋ or － key, and select the reset mode.
[ResetMode]
（2） Push the
Auto
（3） Transition to the following screen by the model.
Model：EMU4-HM1-MB → To 2-1
[N]
Model：EMU4-PX4 → To 2-2 (The [N] changes, and screen turned to setting of next CH.)
EMU4-PX4 only
3 Setup the operation time measurement
3-1.
（1） In 3-1, Push the ▲ or ▼ key, and move the cursor to the "2 OP.Time".
[I/O]
（2） Push the
1 Input
（3） 3-2 will be displayed.
2
OP.Time
3 Output
3-2.
（1） Push the ＋ or － key, and select the operation time measurement . (On/Off)
[OP.Time]
（2） Push the
（3） Transition to the following screen by the model, and setting wiring type and existence of
Off
the operation time measurement.
[1]
Model：EMU4-PX4 → To 3-4
Model：Other than EMU4-PX4
Model:EMU4-PX4 or
2 circuit measurement and [Off] setting → To 3-4
2 circuits measuring
only
non-2 circuit measurement and [Off] setting → To 3-1
[On] setting → To 3-3
3-3.
（1） Push the ＋ or －
[OP.Time
（2） Push the
Mode]
（3） Transition to the following screen by the setting wiring type.
A
2 circuit measurement → To 3-4
[1]
non-2 circuit measurement → To 3-1
2 circuits
measuring only
3-4.
（1） Push the ＋ or －
[OP.Time]
（2） Push the
（3） Transition to the following screen by the model, and setting existence of the operation
Off
time measurement.
[2]
Model：EMU4-PX4 → To 3-6
Model：Other than EMU4-PX4
[Off] setting → To 3-1
[On] setting → To 3-5
3-5.
（1） Push the ＋ or － key, and select the operation time measurement mode.
[OP.Time
（2） Push the
Mode]
（3） 3-1 will be displayed.
A
[2]
3-6.
（1） Push the ＋ or － key, and select the operation time measurement .
[OP.Time]
（2） Push the
（3） 3-7 will be displayed.
Off
[3]
3-7.
（1） Push the ＋ or －
[OP.Time]
（2） Push the
（3） 3-1 will be displayed.
Off
[4]
4 Setup Output
EMU4-HM1-MB, EMU4-A2, EMU4-VA2, EMU4-PX4, EMU4-AX4
（
4-1.
（1） In 4-1, Push the ▲ or ▼ key, and move the cursor to the "3 Output".
[I/O]
（2） Push the
1 Input
（3） 4-2 will be displayed.
2 OP.Time
3
Output
Operation
）
/ Phase
key.
/ Phase
key.
*In the case N=4 → To 2-1
▼
－ key, and change the "CONV.Rate" value and unit.
＋
/ Phase
key, and confirm the setting value.
*In the case N=4 → To 2-1
/ Phase
key.
*In the case N=4 → To 2-1
All models except for EMU4-LG1-MB
（
/ Phase
key.
/ Phase
key.
key, and select the operation time measurement mode.
/ Phase
key.
key, and select the operation time measurement .
/ Phase
key.
/ Phase
key.
/ Phase
key.
key, and select the operation time measurement .
/ Phase
key.
/ Phase
key.
<EMU4-HM1-MB>
[Input]：Non
<EMU4-PX4>
[Input]：Pulse ⇔Contact⇔Non⇔
[CONV.Rate]：0.001～10000（1.000）
[Unit]：Non ⇔Wh⇔kWh⇔MWh⇔J⇔m
[ResetMode]：Auto ⇔Hold⇔
Auto...Contact input state is reset automaticaly when contact
Hold...Contact input state is hold until contact input released
[N] at the bottom right of the screen represents CH. (N=1 to 4)
）
[OP.Time]：Off⇔On⇔
EMU4-HM1-MB
[OP.Time Mode]：A⇔x⇔
EMU4-BM1-MB, EMU4-A2, EMU4-VA2
[OP.Time Mode]：A
EMU4-PX4
Input setting value is set contact, this CH is not displayed.
Operating time is integrated time while the current measured
value is higher than the rated current, Current cut-off rate when
select A.
Operating time is integration time while Contact input is ON when
Contact input.
）
- 7 -
Note
⇔Contact⇔Pulse⇔
2
⇔m
min⇔hour⇔piece⇔set⇔g⇔kg⇔t⇔¥⇔$⇔
input is less.
even thought contact input is less.
(For information about how to release of the contact
input, please refer to the "user's manual (Details)")
3
⇔L⇔kL⇔sec⇔
Advertisement
Table of Contents
