Table of Contents
Advertisement
Screen
11-3.
（1） Push the ▲ ▼ ＋ － key, and change the Ior difference converted
[DIF.Ior]
reference value.
（2） Push the
0.00 mA
（3） 11-1 will be displayed.
12 Setup the AD Converted
（
12-1.
（1） In 12-1, push the ▲ or ▼ key, and move the cursor to the "11 AD CONV.".
[Measure]
（2） Push the
9 SimpleMEA
（3） 12-2 will be displayed.
10DIF.CONV.
11AD CONV.
12-2.
（1） Push the ＋ or － key, and select the AD converted([On]／[Off]).
[AD CONV.]
（2） Push the
On
（3） Transition to the following screen by the setting AD CONV.（[On]／[Off]）
[On] setting → To 12-3
[N]
[Off] setting → To 12-2 (The [N] changes, and the screen changes to the next CH setting.)
12-3.
（1） Push the ＋ or － key, and select the input range.
[Range]
（2） Push the
Current
（3） 12-4 will be displayed.
[N]
12-4.
（1） Push the ▲
[Moving
（2） Push the
average]
（3） 12-5 will be displayed.
001 times
[N]
12-5.
（1） Push the ▲
[Scaling]
（2） Push the
Upp.: 04095
（3） 12-2 will be displayed. (The [N] changes, and screen turned to setting of next CH. )
Low.: 00000
*In the case N=4 → 12-1 will be displayed.
Unit:Non
[N]
13 Setup the Number Limit
（
13-1.
（1） In 13-1, push the ▲ or ▼ key, and move the cursor to the "12 Num.Limit".
[Measure]
（2） Push the
10DIF.CONV.
（3） 13.1-1 will be displayed.
11AD CONV.
12Num.Limit
13.1 Setup the Limit A, Limit B, Limit C, and Limit D
13.1-1.
（1） In 13.1-1, push the ▲ or ▼ key, and move the cursor to the "1 Limit A".
[Num.Limit]
（2） Push the
1
Limit A
（3） 13.1-2 will be displayed.
2 Limit B
*Limit B, Limit C, and Limit D is done in the same way as the setting of Limit A.
3 Limit C
13.1-2.
（1） Push the ▲
[Limit A]
（2） Push the
-32767
（3） The [N] changes, and screen turned to setting of next CH.
In the case N=4 → 13.1-1 will be displayed.
[N]
13.2 Setup the multiplying factor
13.2-1.
（1） In 13.2-1, push the ▲ or ▼ key, and move the cursor to the "5 Factor".
[Num.Limit]
（2） Push the
3 Limit C
（3） 13.2-2 will be displayed.
4 Limit D
5
Factor
13.2-2.
（1） Push the
[Factor]
（2） Push the
x1
（3） The [N] changes, and screen turned to setting of next CH.
In the case N=4 → 13.2-1 will be displayed.
[N]
14 Save the settings
14-1.
（1） After setting all of the items, and push the Setup key.
Quit Setup
（2） 14-1 will be displayed.
1
Save
（3） When save the settings, push the
2 Not Save
and push the
3 Cancel
（4） After completing the settings saving, 14-2 will be displayed. Push the
14-2.
（5） Return to the operation mode.
Completed
OK
*Setting for condition of the measurement mode can only configure in the display unit is set to master.
(Setting for condition of the measurement mode can not configure in the display unit is set to slave. )
*If you change a settings, please push the
*The underline means the default of setting. After you have been set, even if a power failure occurs does not disappear setting.
*If you want to set the other circuit, push the Circuit key on the "Setup" screen (1-1), select the circuit, make the setting.
*Same voltage system is same setting in wire system, primary voltage, 2 circuits Measuring existence, Simple measurement.
7.2.2 Input/Output setup－the settings for the external Input/Output. EMU4-LG1-MB is not set.
Screen
1 Transit to the Setup mode
1-1.
（1） Push the Setup key in operation mode.
[Setup]
（2） 1-1 will be displayed.
1 Measure
（1） Push the ▲ or ▼ key, and move the cursor to the "2 I/O".
2
I/O
3 COM.
Push the
（2） 2-1 will be displayed.
Operation
/ Phase
key,and confirm the setting value.
EMU4-AX4 only
）
/ Phase
key.
/ Phase
key, and confirm the setting value.
*In the case N=4 → To 12-1
/ Phase
key, and confirm the setting value.
▼
－ key, and change the number of moving average.
＋
/ Phase
key, and confirm the setting value.
▼
－ key, and change the upper limit, lower limit, and unit.
＋
/ Phase
key, and confirm the setting value.
EMU4-AX4 only
）
/ Phase
key.
EMU4-AX4 only
（
/ Phase
key.
▼
－ key, and change the set value.
＋
/ Phase
key.
EMU4-AX4 only
（
）
/ Phase
key.
or － key, and select the multiplying factor displayed.
＋
/ Phase
key.
▲ or ▼ key, move the cursor to the "1 Save",
/ Phase
key.
/ Phase
key and be sure to determine changes. If without determine, the changes will be discarded.
Operation
/ Phase
key.
）
/ Phase
key.
- 6 -
Note
High SENS mode
[DIF.Ior]：0.00～100.00mA
Low SENS mode
[DIF.Ior]：0～1000mA
[AD CONV.]：Off⇔On⇔
AD CONV....The setting value is set in AD convert per CH.
[Range]：Current ⇔Voltage⇔
[Moving average]：001～100（001）
[Upp]：-32767～32767（4095）
[Low]：-32767～32767（0）
[Unit]：Non ⇔A⇔mA⇔kA⇔V⇔kV⇔W⇔kW⇔MW⇔Hz⇔N⇔
kN⇔Pa⇔kPa⇔MPa⇔C⇔deg⇔%⇔
[N] at the bottom right of the screen represents CH. (N=1 to 4)
Num.Limit...Set any limit.
*If the scaling value over the limit, Number Limit countup.
Limit...Set any scalling value.
You can configure the four different limits for limit A,
limit B, limit C, and limit D.
[Limit A]：Scaling Low
～Scaling Upp
*If scaling setting value is set "Scaling Low > Scaling Upp",
default setting is Scaling Upp.
[N] at the bottom right of the screen represents CH. (N=1 to 4)
[Factor]：x1 ⇔x10⇔x100⇔x1000⇔
Factor...Set up the multiplying factor displayed of Number Limit.
[N] at the bottom right of the screen represents CH. (N=1 to 4)
1 Save
→ Save settings and return to
the operation mode.
2 Not Save → Discard the changes and
return to the operation mode.
3 Cancel
→Continue the setup.
Note
Advertisement
Table of Contents
