Advertisement
Quick Links
CFN ISLANDER II
WITH KEY OPTION
CONVERSION MANUAL
C36053
REV. 04/15/03
Copyright 2003 by Gasboy International LLC All rights reserved.
The information in this document is confidential and proprietary. No further disclosure shall be made without
permission from Gasboy International LLC. Gasboy International LLC believes that the information in this document
is accurate and reliable. However, we assume no responsibility for its use, nor for any infringements of patents or
other rights of third parties resulting from its use. We reserve the right to make changes at any time without notice.
GASBOY INTERNATIONAL LLC LANSDALE, PA
Advertisement
Related Manuals for Gasboy CFN ISLANDER II
Summary of Contents for Gasboy CFN ISLANDER II
- Page 1 The information in this document is confidential and proprietary. No further disclosure shall be made without permission from Gasboy International LLC. Gasboy International LLC believes that the information in this document is accurate and reliable. However, we assume no responsibility for its use, nor for any infringements of patents or other rights of third parties resulting from its use.
-
Page 3: Using This Manual
USING THIS MANUAL These instructions are provided to assist the system operator in the conversion of a GASBOY CFN Islander II (mag or optical) system, or satellite islander (mag or optical) reader to a key version. The instructions contain: •... - Page 4 Islander II With Key Option Conversion CONTENTS OF THE CONVERSION KIT 04/15/03...
- Page 5 Islander to FleetKey Conversion CONTENTS OF THE CONVERSION KIT (C05898) Item Part No. Description C04371 Trim edge material (2”) C36030 PCB I/F mounting brkt. C04037 2 Screws, #8-32 x 3/8 C05159 Key I/F PCB assembly C04125 2 F/Fstandoffs, #8-32 x 1 C01166 3 Split lock washers, #6 C04039...
-
Page 6: Conversion Instructions
Islander II With Key Option Conversion CONVERSION INSTRUCTIONS Use the following instructions to convert your system. The first two subsections detail removal of your old Mag or Optical card reader unit. The next section details installation of the new key unit(s). - Page 7 Islander to FleetKey Conversion 4. Still inside the head, remove the two screws which secure the optical reader bracket to the inside face of the unit (the same two screws help secure the bottom of the external card reader cover assembly). Remove the entire optical reader assembly from the head. 5.
- Page 8 Islander II With Key Option Conversion INSTALLATION OF KEY SYSTEM 1. From the outside of the unit, insert the two threaded studs of the conversion kit single or dual key adapter bracket into the two mounting holes in the face of the unit where the mag or optical card reader was mounted.
- Page 9 Islander to FleetKey Conversion PARTIAL FRONT VIEW PARTIAL INTERIOR SIDE VIEW 04/15/03...
- Page 10 Turn on the power for the Islander unit again. If the unit still will not power up, contact Gasboy Technical Service at (800)444-5529. 2. Using a calibrated multimeter, measure the +5 VDC between TPI (+) and TP2 (-). The voltage should be +5.05 ±...
- Page 11 Islander to FleetKey Conversion CONFIGURING THE SITE CONTROLLER A Key option is available for Islander II sites. The following configuration adjustments must be made to the Site Controller configuration for this option. SYSTEM PARAMETERS (SYS PAR) The following setting must be used to configure the Site Controller to accept keys. •...
- Page 12 Islander II With Key Option Conversion • Miles-per-gallon package - page 13 The Key option on the CFN allows the odometer to be stored on the key for reasonableness check. If you are using this option, when the user enters the odometer, it is verified at the reader against the odometer stored on the key.
- Page 13 HQÂGA Â ↵ Gs“5Â !"#$ Â ↵ Â Upon completion of this Configuration section, your converted Islander with Key option system should be working and fully operational. If you have any questions, please call Gasboy Technical Services at 1-800-444-5529. 04/15/03...