Dacor DRW24980RAP/LAP Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Dacor Manuals
  4. Wine Cooler
  5. DRW24980RAP/LAP
  6. Installation instructions manual
Dacor DRW24980RAP/LAP Installation Instructions Manual

Dacor DRW24980RAP/LAP Installation Instructions Manual

Built-in wine cellar
Hide thumbs
Table of Contents

Advertisement

Quick Links

Installation Instructions
Built-In Wine Cellar
DRW24980RAP/LAP

Advertisement

Table of Contents
loading

Related Manuals for Dacor DRW24980RAP/LAP

Summary of Contents for Dacor DRW24980RAP/LAP

  • Page 1 Installation Instructions Built-In Wine Cellar DRW24980RAP/LAP...

  • Page 2: Table Of Contents

    Contents Before You Begin Important Customer-Service Information If You Need Help Important Safety Instructions State of California Proposition 65 Warning (US only) General Safety Precautions Safety and Warning Information Installation Safety Installation Specifications Installation Options Product Specifications Custom Panel Specifications Handle Specifications Installation Installation Requirements...
  • Page 3 Installation Instructions 1. Uncrating the Wine Cellar 2. Moving the Wine Cellar 3. Installation Preparation 4. Attaching the Anti-tip-Bracket 5. Removing Upper Door Cover, Kickplate 6. Attaching Insulators on the Side of the Wine Cellar - Single Installation 7. Attaching insulators on the side of the freezer or fridge or Wine Cellar - Side-by-side (Pair) Installation 8.

  • Page 4: Before You Begin

    Before You Begin Important Installer • To promote safety and minimize problems, read this manual thoroughly before starting the installation. Leave this manual with the user. • Write the appliance’s model/serial numbers in this manual for service/ maintenance reference. • Model/serial numbers are on the data label in the Wine Cellar compartment.

  • Page 5: Customer-Service Information

    Customer-Service Information If You Need Help If you have questions or problems with installation, contact your Dacor® dealer or the Dacor Customer Assurance Team. If your Dacor appliance is under warranty, call Dacor Distinctive Service. Have the appliance’s model/serial numbers available when you call.

  • Page 6: Important Safety Instructions

    Use common sense and caution when installing, maintaining, or operating this or any other appliance. Always contact the Dacor Customer Assurance Team about problems and conditions that you don’t understand. See Customer-Service Information. Safety symbols and labels These alerts are meant to bring attention to important areas in the manual.

  • Page 7: General Safety Precautions

    WARNING - R600a Refrigerant This appliance contains isobutane refrigerant, R600a, a natural gas with high environmental compatibility; however, it is also flammable. Please adhere to the warnings below • When handling, installing and operating the appliance, care should be taken to avoid damage to the refrigerant tubing.
  • Page 8 Important Safety Instructions To avoid the possibility of explosion or fire, do not store or use combustible, flammable or explosive vapors and liquids (such as gasoline) inside or in the vicinity of this or any other appliance. Also keep items that could explode, such as aerosol cans away from cooktop burners, ovens and range hoods.
  • Page 9 WARNING • To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: • If you receive a damaged product, immediately contact your dealer or builder. Do not install or use a damaged appliance.
  • Page 10 Important Safety Instructions • If the power cord is damaged, it must be replaced by the manufacturer or a qualified service technician in order to avoid a safety hazard. Do not tamper with the controls. • Clean this appliance regularly as instructed in the Care and Cleaning section of the User manual.

  • Page 11: Safety And Warning Information

    Safety and Warning Information Installation Safety WARNING • Before installing the wine cellar, connect it to a power outlet and turn the wine cellar ON to make sure the wine cellar is working. • Choose a location away from a heater, boiler, or direct sunlight. •...
  • Page 12 Safety and Warning Information DANGER Explosion Risk Keep flammable materials and vapors - such as gasoline - away from the wine cellar. Failure to do so can result in death, explosion, or fire. English...

  • Page 13: Installation Specifications

    Installation Specifications WARNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. WARNING Electrical and grounding connections must comply with the applicable portions of the national electrical code and/or other local electrical codes. This appliance comes with an electrical cord with a three-prong grounding plug for a 115 Vac, 15 Amp.

  • Page 14: Installation Options

    Installation Options There are many different installation options. These are limited only by the design of the kitchen. Individual appliance Side-by-Side (Pair) English...
  • Page 15 If a 115 degree door opening angle is desired, Distance of “F” (16 page) for a partition thickness is recommended. • Partition thickness is dependent on handle depth. Dimension above is acceptable for Dacor handles. 1 1/4” (32 mm) 1 9/16” (40 mm) 1 9/16”...

  • Page 16: Product Specifications

    Product Specifications 115° 90° Callout 24” 23 3/4” (603 mm) B (With Panel) 25” (635 mm) B1 (Without Panel) 23 13/16” (605 mm) 83 3/8” (2118 mm) 23 5/8” (600 mm) 24 7/8” (631 mm) 27 9/16” (701 mm) 50 3/4” (1289 mm) 13 11/16”...

  • Page 17: Custom Panel Specifications

    Custom Panel Specifications Callout 24” 23 3/4” (603 mm) 3 9/32” (83.5 mm) 17 5/32” (436 mm) 79 7/8” (2029 mm) 7 23/32” (196 mm) 62 25/32” (1594.5 mm) 9 3/8” (238.5 mm) Panel Thickness 3/4” (19 mm) Max Weight 55.0 lb (25 kg) Do not exceed the max load that the custom panel can endure.

  • Page 18: Handle Specifications

    Countersunk screw Handles are not provided with custom panel models. Selected handle kits are available through your Dacor dealer. Dacor Custom does not advise the use of single pull panel knobs. Appliance...
  • Page 19 Attach the Dacor Handle WARNING Follow these instructions to attach the Dacor handle. Otherwise, the handle may be damaged or malfunction. 1. Put the reinforced handle support on the rear of the door panel, and then put the handle on the front of the door panel.

  • Page 20: Installation

    Installation WARNING Do not install the appliance: • outdoors, • in an environment with dripping water. Appliance is very heavy : Wine Cellar 24” approx. 397 lb / 180 kg Installation room The appliance should be installed in a dry, ventilated room. Secure installation The appliance is very heavy and has a tendency to tilt forwards when the appliance door is opened.

  • Page 21: Installation Requirements

    Installation Requirements Installation Preparation Cabinet installation parts Using the table on next page, verify that all installation parts are present as you unpack the appliance. A2-1 A2-2 Check the installation parts when unpacking. PARTS SINGLE-INSTALLATION PAIR-INSTALLATION LEVER A2-1 LOWER BRACKET A2-2 UPPER BRACKET KICKPLATE...
  • Page 22 Installation Requirements Door installation parts Using the table below, verify that all door-installation parts are present as you unpack the appliance. Check the installation parts when unpacking. PARTS SINGLE-INSTALLATION PAIR-INSTALLATION A’ LOWER DOOR CAP B’ C’ DOOR SIDE TRIM D’ PANEL BRACKET Screw and Nut M6x12...
  • Page 23 Tools required Tool Tool Electric Screwdriver Protective Floor Mat Measuring Tape Stepladder Flat/Slot Head Appliance Dolly Screwdriver Cutter (Scissors) Cutter Adjustable Wrench Level Phillips Head Star Head Screwdriver Screwdriver Ratchet Combination Wrench 3/8” (10 mm), 3/8” (10 mm), 1/2” (13 mm) 1/2”...

  • Page 24: Grounding The Wine Cellar

    Installation Requirements Grounding the Wine Cellar CAUTION Electrical and grounding connections must comply with the applicable portions of the national electrical code and/or other local electrical codes. This appliance comes with an electrical cord with a three-prong grounding plug for a 115 Vac, 15 Amp.

  • Page 25: Cabinet Special Requirements

    Cabinet Special Requirements A : Cabinet Width B : Cabinet Depth Electric supply location C : Cabinet Height D : Electrical supply width location E : Electrical supply height location 5” (127) Callout 24” 24” (610 mm) 25” (635 mm) 84”...

  • Page 26: Installation Instructions

    Installation Instructions 1. Uncrating the Wine Cellar Check the appliance for transit damage. Do not install the appliance if it is visibly damaged. If in doubt, contact your dealer. 1. Remove the PP-banding, cardboard crate, EPS, and Pe-bag. 2. Remove the brackets from the pallet by unscrewing the bolts (five per bracket). M6x10 10 ea Unscrew the bolts...

  • Page 27: Moving The Wine Cellar

    2. Moving the Wine Cellar WARNING The appliance is very heavy. When moving the , all personnel must take care not to injure themselves or the appliance. Secure the to a suitable means of transport (preferably an appliance dolly), and move the near its installation cabinet.

  • Page 28: Installation Preparation

    Always wear safety glasses and other necessary protective devices or apparel when installing or working with anchors. Dacor does not recommend that you anchor the anti-tip bracket in light-weight masonry (e.g., block, brick) or in new, uncured concrete. Make sure the wall or the cabinet that the brackets are studded in has enough strength to withstand the safety load.
  • Page 29 For 36” models, use 2 anti-tip brackets. Spacer (wood) 2” (50) Appliance Appliance Option Cabinet height 83 1/2” (2121 mm) 79 13/32” (2017 mm) 83 3/4” (2127 mm) 79 5/8” (2023 mm) 84” (2134 mm) 79 7/8” (2030 mm) 84 1/4” (2140 mm) 80 1/8”...
  • Page 30 Installation Instructions Anti-tip bracket considerations 1. Bracket positioning: follow the cabinet- specific height table. 2. Screws: Tighten all 3 screws on the Wall brackets. 3. Push the product up against the rear wall of the cabinet. 4. Spacer: If using the spacer, you must Anti-Tip-Bracket follow the positioning specifications of the bracket (see the table above).

  • Page 31: Removing Upper Door Cover, Kickplate

    5. Removing Upper Door Cover, Kickplate You need to remove the upper door cap and kickplate before you adjust the custom door panel. Upper Door Cover Kickplate Upper Door Cover M5x16 2 ea Kickplate M4x8 2 ea English 31...
  • Page 32 Installation Instructions 1. Remove the inner cover on the inner part of the upper door cover. 2. Disconnect the humidity sensor connector. 3. Remove the 2 screws fixing the upper door cover. 4. Remove the upper door cover from the fixers.
  • Page 33 • Kickplate : For side-by-side installation, remove the grill cover. This is not applicable for standard one installation. 1. Push open the cover.Remove the screws on side and remove grill cover. WARNING Do not use impact drill. Can cause damage. 2.

  • Page 34: Attaching Insulators On The Side Of The Wine Cellar - Single Installation

    Installation Instructions 6. Attaching Insulators on the Side of the Wine Cellar - Single Installation Check your model first, and then attach the insulators by referring to the figure below. Attach the insulators to cover the screws on the chassis spacers. Align the insulators with the end of the center chassis spacer.

  • Page 35: Side-By-Side (Pair) Installation

    Attaching insulators on the side of the freezer or fridge Wine Cellar - Side-by-side (Pair) Installation Attach 2 insulators on any one side of the freezer or the fridge. The insulators are different in size according to the type. Check your model first, and then attach the insulators by referring to the figures below.
  • Page 36 Installation Instructions 2. When a freezer is on the right-hand side See the figures below for the layout after the insulator is attached. Top View 18”/24”/30”/36” 24” Rear Wine cellar Freezer 1/8” Front (3 mm) Side View Fridge or Wine cellar Freezer English...
  • Page 37 Repositioning the Center Chassis Spacers 1. Remove the set’s center chassis spacer. 2. Re-attach the spacers 7/16 in. (10 mm) back from their original position (see graphic below). Chassis 7/16” (10 mm) Center Chassis Spacers English 37...

  • Page 38: Connecting The Two Chassis

    Installation Instructions 8. Connecting the Two Chassis 1. Making the upper connection. - Attach the rectangular bracket to the protruding tabs on the top of each chassis (see the graphic). - Attach the lever to connect the two chassis. 2. Making the lower connection. - Insert the bracket in the groove at the bottom of the two chassis.

  • Page 39: Adjusting The Door Opening Angle

    9. Adjusting the oor Opening Angle By factory default, the door opens by 115 degrees. You can use the limiter pin to adjust the opening angle down to 90 degrees, depending on the installation conditions. • Open the door to less than 90 degrees, and then completely insert the limiter pin through the top and bottom holes of the top hinge as shown in illustrations (1) and (2).

  • Page 40: Moving The Wine Cellar Into Its Enclosure

    Installation Instructions 10. Moving the Wine Cellar Into Its Enclosure • According to the type of cabinet, a jig (positioning aid) can be used to align the s custom door panel with cabinet by marking vertical line on the cabinet. Overlay Frameless Jig (positioning aid)
  • Page 41 CAUTION As you push the wine cellar into its enclosure, take care not to damage the power cord. Also, arrange the power cord behind the appliance to ensure that it is not stepped on or over. WARNING While moving the wine cellar, take care not to harm assisting personnel or the itself.

  • Page 42: Removing Two Levers

    Installation Instructions 11. Removing Two Levers • To facilitate leveling on the wine cellar, remove the top and bottom levers to unpair the chassis. • To disassemble lower lever, use a screwdriver by force. Lever Bracket Bracket Lever English...

  • Page 43: Leveling The Wine Cellar

    12. Leveling the Wine Cellar Using your drill and the bit shown 10 mm bit wine cellar below, engage each of the ’s adjuster shafts in turn, and level the , CCW Adjust the gap between the furniture top cover to 1/8 in. (3 mm).
  • Page 44 Installation Instructions Front Rear Adjustable shaft (10 mm) Max 3/4”, 20 mm Jack type (height adjustment) English...

  • Page 45: Attaching Two Levers

    13. Attaching Two Levers • Attach the top and bottom levers to pair the chassis. Lever Bracket Bracket Lever English 45...

  • Page 46: Attaching The Wine Cellar's Top Cover

    Installation Instructions 14. Attaching the Wine Cellar’s Top Cover The light intensity sensor is attached to the top cover. The wine cellar does not use the light intensity sensor, therefore do not connect the sensor connector. 1. Connect the wires for electric parts Product top view from around the Auto Door Open kit, and then insert the wires in the...

  • Page 47: Securing The Wine Cellar

    15. Securing the Wine Cellar Secure the to its enclosure with (TH) M4x16 screws (6 screws per side, as shown in the graphic). CAUTION Make sure the appliance is level. If the appliance is not level, the wine rack may slide in or out.

  • Page 48: Attaching The Custom-Door-Panel Brackets

    Installation Instructions 16. Attaching the Custom-Door-Panel Brackets Attach the panel brackets to the top and bottom of the panel. Custom Panel: STS Drive 10 screws each to the top and bottom brackets as shown in the graphic. (The other holes on each side of the bracket are for a different application.) (FH) M4x14 20 ea UPP : 10 ea / LOW : 10 ea Screw Hole...
  • Page 49 Custom Panel: Recessed Back, Other If, by the nature of its design, the panel cannot be attached at the center of the bracket, use the whichever suitable screw holes on the sides of the bracket to attach the panel. Front 3/4”...

  • Page 50: Hanging A Custom Panel

    Installation Instructions 17. Hanging a Custom Panel WARNING If you install a custom panel before fixing the appliance to the cabinet, the custom panel can tip over. To prevent this, you must follow the installation instructions. • Hang the panel bracket on the height adjustment screw. (See the graphic.) English...

  • Page 51: Preparing The Panel For Adjustment

    18. Preparing the Panel for Adjustment 1. Fix the custom panel temporarily onto the side of the door by tightening the screw in the center of the panel. 2. Loosen—but do not remove—the six screws on the side of the door so you can adjust the custom panel vertically.

  • Page 52: Aligning The Panel

    Installation Instructions 19. Aligning the Panel NOTE Each custom panel comes with 12 dedicated screws for fine-tuning. Use a minimum number of screws to fine-tune the custom panel with the cabinet. Once fine-tuning is complete, fix the custom panel with the top nut. There are two panel-adjustment mechanisms at the top and two at the bottom of the door.
  • Page 53 The gap between the glass door and the panel must be same on all sides (top, Glass Door bottom, left, and right) or the difference should be no more than 2/32" (2 mm). (For example, if A is 2 mm, B should not exceed 4 mm.) Panel Top of the Door...
  • Page 54 Installation Instructions 1. Engage Double Threaded Bolt (see the graphic) to shift the panel up and down. 2. Engage a side screw (see the graphic) to shift the panel side to side. CAUTION Be careful not to damage the wires when fastening the side screw. 3.
  • Page 55 Top of Door Up/Low Left/Right Front/Rear Bottom of Door Left/Right Front/Rear Attaching the Panel to the Door 1. Screw nuts snugly onto the double-threaded bolts. 2. Fasten the screws to assemble the panel and the door as shown in the figure. Two nuts per set Six screws per side Six screws per side...

  • Page 56: Attaching The Door's Interior Covers

    Installation Instructions 20. Attaching the Door’s Interior Covers Upper Door Cover 1. Connect the humidity sensor connector, and then arrange the wires as shown in the figure. 2. Assemble the inner cover. 3. Insert both side rings of the door cap of the upper door cover into the fixer.
  • Page 57 4. Fasten the 2 screws to fix the upper Upper door cover door cover. Upper door cover M5x16 2 ea English 57...
  • Page 58 Installation Instructions Lower Door Cover 1. Attach the air guide to the lower door cover (2 screws per set). 2. Attach the lower door cover by driving the screws from the front (2 screws per set). 3. Attach the caps over the screw holes. Lower Door Cover Caps Lower Door Cover...

  • Page 59: Attaching Grill, Kickplate And Toe Kickplate (Optional)

    21. Attaching Grill, Kickplate and Toe Kickplate (optional) Attaching grill • Drive the screws tightly on both sides to attach the grill. Otherwise, the door may not close fully. Attaching kickplate • Drive the screws on both sides to attach the kickplate. Kickplate M4x8 2 ea Kickplate...
  • Page 60 • The height of the product can be adjusted between 83 3/8” ~ 84 3/8”. • If you want to use the provided Dacor toe kickplate (4”), note that it was designed for a product height of 83 7/8” and cabinet height of 84”.

  • Page 61: Attaching The Wine Cellar Trim

    22. Attaching the Wine Cellar Trim 1. Cabinet-side trim: Attach the trim between the and the cabinet. WARNING Please check again if there is any problem after installation. Top View Chassis spacer Cabinet- side trim 2. Door-side trim: Attach trim to the door’s side bracket. •...

  • Page 62: Attaching Trim Top Cover

    Installation Instructions 3. (Side-by-side installation only) Center trim: Attach the trim between the chassis. WARNING Please check again if there is any problem after installation. Center trim 23. Attaching Trim Top Cover Attach the Trim Top Cover on the bottom of the Top Cover. •...

  • Page 63: Assembling The Wine Rack

    24. Assembling the Wine Rack 1. Remove the packaging of the bottom wine shelf, and then place it on the bottom of the wine cellar. 2. Remove the rail English 63...
  • Page 64 Installation Instructions 3. Hold the front part of the wine rack and the rail, and then push the wine rack so that the hook on the back of the rail is inserted into the hole on the back of the wine rack as shown in the figure.
  • Page 65 5. Place 3 Bottle Presenter on the wine Bottle Presenter rack of the Presentation Zone. 3 ea 6. Slide in the wine rack until you hear a clicking sound. English 65...

  • Page 66: Disassembling The Wine Rack

    Installation Instructions WARNING • Make sure the appliance is level. If the appliance is not level, the wine rack may slide in or out. • Make sure the wine rack is firmly fixed. 25. Disassembling the Wine Rack 1. Pull the wine rack. 2.

  • Page 67: Adjusting The Door Spring

    26. Adjusting the Door Spring Adjust the tension of the door spring according to the product size. With a star-head screwdriver, turn the adjusting screw. I = maximum spring tension 0 = no spring tension 27. Cleaning Remove the protective vinyl. English 67...

  • Page 68: Installation Checklist

    • Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor appliance cannot be overemphasized. Installation Checklist Has the unit been inspected for cosmetic damage?
  • Page 69 Memo...
  • Page 70 Memo...
  • Page 71 Memo...
  • Page 72 DA68-03621J-01 Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745 ∙ Phone: (800) 793-0093 ∙ Fax: (626) 403-3130 ∙ www.dacor.com...

Table of Contents