Belshaw Brothers 718LCG Operator's Manual

Donut fryer. open kettle gas fryers

Hide thumbs Also See for 718LCG:

Operator's manual (42 pages)

Table of Contents

Quick Links

The #1 Source for Donut and Bakery Equipment

O P E R A T O R ' S M A N U A L

T E C H N I C A L S U P P L E M E N T

P A R T S A N D E L E C T R I C A L D I A G R A M S

718LCG-724CG-734CG

Donut Fryer • Gas Heated • Electronic Ignition

ITEM NUMBERS



21263-10 (718LCG)



21273-10 (724CG)



21276-10 (734CG)

SERIAL NUMBER

Item Number / Serial Number are listed on a data tag attached to the equipment.

This manual should only be used with the Item Number(s) shown above.

SUPPORT



21264-10 (718LCG)



21281-10 (724CG)



21277-10 (734CG)

USA/Canada 1-800-578-2547

International (+1) 206-322-5474



21267-10 (718LCG)



21282-10 (724CG)



21278-10 (734CG)

Email service@belshaw.com

Web www.belshaw.com

www.belshaw.com

Manufactured

2018

or later

Photo: Belshaw

724CG Gas Fryer

shown with Type F

Depositor and EZMelt

24 Melter-Filter.



21268-10(718LCG)



21287-10 (724CG)



21283-10 (734CG)

Table of Contents

Chapters

Table of Contents

Need help?

Do you have a question about the 718LCG and is the answer not in the manual?

Questions and answers

Summary of Contents for Belshaw Brothers 718LCG

Page 1 Type F Depositor and EZMelt 24 Melter-Filter. 718LCG-724CG-734CG Donut Fryer • Gas Heated • Electronic Ignition ITEM NUMBERS     21263-10 (718LCG) 21264-10 (718LCG) 21267-10 (718LCG) 21268-10(718LCG)     21273-10 (724CG) 21281-10 (724CG) 21282-10 (724CG) 21287-10 (724CG) ...
Page 2 Open Kettle Gas Fryers 718LCG, 724CG & 734CG Operator’s Manual Belshaw Adamatic Bakery Group. 814 44 Street Northwest, Suite 103 Auburn, WA 98001 USA Phone: (206) 322-5474 • Fax: (206) 322-5425 E-mail: service@belshaw.com • www.belshaw.com...
Page 3 BELSHAW-ADAMATIC FREIGHT To unpack the fryer and transport it to the DAMAGE POLICY workstation: Belshaw-Adamatic has made every effort to Use a fork lift to transport the shipping crate insure that your equipment arrives in good to the work station. condition.
Page 4: Table Of Contents
Contents Preface Operation Taking Safety Precautions Filling with Shortening If the Pilot Light Fails to Ignite High Temperature Limit Switch Adding Shortening to the Fryer Fill up to “OIL LEVEL” Marks Cleaning Removing the Shortening Washing Rinsing Donut-Making Helps Tips on Making Quality Cake Donuts Calculating Correct Water Temperature Ratios of Plunger Sizes to Donut Weights Temperature Conversion...
Page 5: Preface
Preface The 718LCG, 724CG, and 734CG Gas Fryers are get spilled on the floor, mop it up designed to fry cake and yeast-raised donut immediately. Materials on the floor can products. Each must be bolted to a flat, dry cause people to slip or fall, resulting in floor.
Page 6: Operation
Operation Taking Safety Precautions * If you have a Belshaw EZMelt shortening melter-filter, warm the In a prominent location, post information about shortening and then transfer it to the what to do if there is a gas leak. Make sure that kettle.
Page 7: If The Pilot Light Fails To Ignite
Above: OMRON Digital Temperature Controller (See diagram above) On the digital If this happens, follow these steps to reset the temperature controller, push the up and down system: arrow keys to adjust the target frying temperature a. Move the on/off switch to the OFF (SV).
Page 8: Fill Up To "Oil Level" Marks
* If you have a Belshaw EZMelt shortening melter-filter, warm the shortening and then transfer it to the kettle. (For EZMelt operating instructions, refer to the EZMelt operator’s manual) * Melt shortening in a pan on the stove and pour it into the kettle. * Very carefully put solid shortening into the kettle.
Page 9: Cleaning
Cleaning For your safety, observe the following warnings 1. Disconnect the machine from the power throughout the entire cleaning process. source. 2. Let the shortening cool to 250°F(120°C). WARNING 3. Place a Belshaw EZMelt Filter under the drain valve of the fryer. (See your EZMelt Thoroughly clean and dry the floor if Operator’s Manual) shortening, water, or other materials are...
Page 10: Washing
WARNING WARNING To avoid fire, serious injury, and Do not use plastic containers. If the equipment damage, do not attempt to burn cleaning solution is not cool enough, the carbon off of the heat tubes. containers will melt; possibly causing you to be burned, and causing cleaning solution to get on the floor.
Page 11 CAUTION WARNING To avoid severe damage to the kettle, never Thoroughly clean and dry the floor if water turn on the heat unless the heat tubes are is spilled. Water on the floor can cause completely covered by liquid. serious injury or loss of life. 2.
Page 12: Donut-Making Helps
Donut-Making Helps Tips on Making Quality If the shortening is too cold, the donuts will spread too rapidly, will form large rings, will Cake Donuts tend to crack open, will be too light in appearance, and will absorb too much •...
Page 13: Calculating Correct Water Temperature
Calculating Correct Water use your own room temperature, dry mix temperature, desired batter temperature, and, if Temperature you are making yeast-raised donuts, estimated temperature increase during mixing. The following is an example of how to calculate the correct water temperature to use. You must Cake Donuts Yeast-Raised Donuts °F...
Page 14 Open Kettle Gas Fryers 718LCG, 724CG & 734CG Technical Supplement Belshaw Adamatic Bakery Group. 814 44 Street Northwest, Suite 103 Auburn, WA 98001 USA Phone: (206) 322-5474 • Fax: (206) 322-5425 E-mail: service@belshaw.com • http://www.belshaw.com...
Page 15 Table of Contents Preface Installation Conforming to Codes Selecting a Workstation Unpacking the Fryer Initial Cleaning Assembling the Fryer Installing the Fryer Moving the Fryer Mounting the Drain Tray Assembling the Frying Screen Handles ...
Page 16: Preface
Preface The 718LCG, 724CG, and 734CG Gas Fryers are get spilled on the floor, mop it up designed to fry cake and yeast-raised donut immediately. Materials on the floor can products. Each must be bolted to a flat, dry cause people to slip or fall, resulting in floor.
Page 17: Installation
Installation In a prominent location, post instructions to be pressure testing of the gas supply piping followed in the event the user smells gas. Obtain system at test pressures equal to or less than this information by consulting your local gas 13.0 IWC (3.45 kPa).
Page 18: Unpacking The Fryer
The workstation should allow at least 2”/5 cm a. Slide the flange on the bottom of the flue clearance between the machine and all stack underneath the retaining strip on construction, whether combustible or the flue base. The mounting holes must noncombustible.
Page 19: Installing The Fryer
holes in the heat shield and the fryer cabinet b. If the fryer is not level, lift the fryer must line up. See Figure 1-2. using a fork lift or pallet jack, and turn the legs to adjust them. c. Using the fork lift or pallet jack, lower the fryer to the floor.
Page 20: Moving The Fryer
must use a compound that resists the Allow the machine and the shortening to action of liquefied petroleum (LP) gases. cool. d. Bleed the gas lines of all air. WARNING e. Check all gas connections and fittings for leaks using a gas leak detector, a Do not touch hot shortening.
Page 21: Mounting The Drain Tray
Mounting the Drain Tray 7. Slide the drain tray hinge shaft through the The drain tray is mounted on the right side of the holes in the mounting brackets and the drain fryer in the factory. To move the drain tray on tray.
Page 22: Assembling The Frying Screen Handles
Assembling the Frying Screen Handles (Be aware that you may be using detachable handles rather than fixed handles, particularly when making raised donuts using screens which are placed inside a proofer. In this case, your handles should NOT be attached to screens.) Frying Screens come with handles and hardware unassembled.
Page 23: Maintenance
Maintenance Open Kettle Temperature Controller Programming procedure (Service Bulletin SB-0439-R3) This service bulletin covers the proper procedure for programing the Omron E5CC-RX3DM-000 temperature controller in an open kettle fryer. The Belshaw part number is TJ-0184C-2. This controller is programmed and protected so the operator cannot change the setup parameters. You must first unlock the controller to adjust the settings.
Page 24 SB-0439 R3 02/06/15 Century and Open kettle fryer Temperature Controller Programming procedure This service bulletin covers the procedure for programing the TJ-0184C-2 (Omron E5CC-RX3DM-000) temperature controller used on Century and Open kettle fryers. The TJ-0184C-2 controller comes per-programmed and protected so the operator cannot change the setup parameters. To change any setting you must first unlock the controller.
Page 25 SB-0439 R3 02/06/15 To change operator level parameters: (Must be unlocked) 1. Press the O key for less than 1 second 2. Press the M key to move to the next parameter 3. Press the U or D to change the parameter 4.
Page 26 SB-0439 R3 02/06/15 To change advanced level parameters: (Must be unlocked) 1. Unlock the controller 2. Press the O key for more than 1 second to adjust intial parameters 3. Press the M key until you get to parameter amov 4.
Page 27: Troubleshooting
Troubleshooting If you have a problem with your fryer that you CAUTION cannot solve, call your dealer or another qualified technician. If you perform repairs yourself or have If your dealer cannot help you, please call them performed by anyone other than a Belshaw Bros.
Page 28: Pilot Module
Step 1: Perform Visual Inspection about the Honeywell S8600 Intermittent Pilot Make sure the fryer’s on/off switch is in the Module. The Belshaw 718LCG, 724CG, and OFF position. Make sure all wiring 734CG gas fryers all use this module. Fryers connections are clean and tight.
Page 29: Main Burner Operation
to spark as long as the fryer’s thermostat calls for Compare this time with the shutoff time that heat or until the pilot lights. is stamped on the module. They should be the same. The S8600H, which is used on propane fryers, provides 100 percent shutoff and safety lockout.
Page 30 START Thermostat calls for heat. TRIAL FOR First main valve opens. IGNITION Gas flows to pilot burner. Igniter-sensor sparks. Pilot burner lights. Pilot burne r does not light, or Module sense s flame current. mod ule d oes not sense flame current. Module S8600H Module S8600 F System locks out.
Page 31: Step 5: Check Normal Operation
Step 5: Check Normal Operation models must be reset by setting the thermostat below 200°F/93°C for at least 1. Move the on/off switch to ON. one minute before continuing. On retry Set the temperature controller to 200°F models, wait for retry or reset at the (93°C) or higher.
Page 32 A common ground, usually supplied by the pilot Check the table below. burner bracket, is required for the module and the pilot burner/igniter-sensor. Check for good metal-to-metal contact between the pilot burner bracket and the Arc Length What To Do main burner.
Page 33 short to ground. Replace the igniter- sensor if necessary. Appearance Cause e. At the gas control, disconnect the main valve wire from the TH or MV terminal. small blue flame lack of gas due to clogged orifice filter f. Connect the fryer to the power source and move the on/off switch to the ON lack of gas due to position.
Page 34 Go To Pages Listed Below MARK FOR YOUR NAT GAS/ FINAL MANIFOLD FRYER ITEM NUMBER MODEL VOLTS PROPANE ASSEMBLY PIPING ELECTRICAL  21263-10 14-15 20-27 718LCG 120V 21264-10 14-15 20-27  718LCG 120V  21268-10 14-15 28-35 718LCG 208-240V  21267-10 14-15 28-35...
Page 35 USE THIS DRAWING ONLY FOR 718G-1303TAB MODEL: 718LCG ITEM NUMBERS: 21263-10, 21264-10, 21267-10, 21268-10 TO IDENTIFY MODEL / ITEM NUMBER, SEE DATA TAG INSIDE FRYER. © Belshaw Adamatic Bakery Group, Auburn, WA 98001 USA. All Rights Reserved. 06/18 DIAGRAMS PAGE...
Page 37 USE THIS DRAWING ONLY FOR 718G-2003TAB MODEL: 718LCG ITEM NUMBERS: 21263-10, 21264-10, 21267-10, 21268-10 TO IDENTIFY MODEL / ITEM NUMBER, SEE DATA TAG INSIDE FRYER. © Belshaw Adamatic Bakery Group, Auburn, WA 98001 USA. All Rights Reserved. 06/18 DIAGRAMS PAGE...
Page 39 USE THIS DRAWING ONLY FOR 724G-1303TAB MODEL: 724CG ITEM NUMBERS: 21273-10, 21281-10, 21282-10, 21287-10 TO IDENTIFY MODEL / ITEM NUMBER, SEE DATA TAG INSIDE FRYER. © Belshaw Adamatic Bakery Group, Auburn, WA 98001 USA. All Rights Reserved. 06/18 DIAGRAMS PAGE...
Page 41 USE THIS DRAWING ONLY FOR 724G-2003TAB MODEL: 724CG ITEM NUMBERS: 21273-10, 21281-10, 21282-10, 21287-10 TO IDENTIFY MODEL / ITEM NUMBER, SEE DATA TAG INSIDE FRYER. © Belshaw Adamatic Bakery Group, Auburn, WA 98001 USA. All Rights Reserved. 06/18 DIAGRAMS PAGE...
Page 43 USE THIS DRAWING ONLY FOR 734G-1303TAB MODEL: 734CG ITEM NUMBERS: 21276-10, 21277-10, 21278-10, 21280-10 TO IDENTIFY MODEL / ITEM NUMBER, SEE DATA TAG INSIDE FRYER. © Belshaw Adamatic Bakery Group, Auburn, WA 98001 USA. All Rights Reserved. 06/18 DIAGRAMS PAGE...
Page 45 USE THIS DRAWING ONLY FOR 734G-2003TAB MODEL: 734CG ITEM NUMBERS: 21276-10, 21277-10, 21278-10, 21280-10 TO IDENTIFY MODEL / ITEM NUMBER, SEE DATA TAG INSIDE FRYER. © Belshaw Adamatic Bakery Group, Auburn, WA 98001 USA. All Rights Reserved. 06/18 DIAGRAMS PAGE...
Page 47 718G-1517TAB USE THIS DRAWING ONLY FOR MODEL: 718LCG ITEM NUMBERS: 21263-10, 21264-10, 21267-10, 21268-10 TO IDENTIFY MODEL / ITEM NUMBER, SEE DATA TAG INSIDE FRYER. © Belshaw Adamatic Bakery Group, Auburn, WA 98001 USA. All Rights Reserved. 06/18 DIAGRAMS PAGE...
Page 49 724G-1517TAB USE THIS DRAWING ONLY FOR MODEL: 724CG ITEM NUMBERS: 21273-10, 21281-10, 21287-10, 21282-10 TO IDENTIFY MODEL / ITEM NUMBER, SEE DATA TAG INSIDE FRYER. © Belshaw Adamatic Bakery Group, Auburn, WA 98001 USA. All Rights Reserved. 06/18 DIAGRAMS PAGE...
Page 51 734G-1517TAB USE THIS DRAWING ONLY FOR MODEL: 734CG ITEM NUMBERS: 21277-10, 21276-10, 21278-10, 21280-10 TO IDENTIFY MODEL / ITEM NUMBER, SEE DATA TAG INSIDE FRYER. © Belshaw Adamatic Bakery Group, Auburn, WA 98001 USA. All Rights Reserved. 06/18 DIAGRAMS PAGE...
Page 53 724G-1718_CV FOR 120V GAS FRYERS PAGE 1 OF 4 MODEL: 718LCG ITEM NUMBERS: 21263-10, 21264-10 MODEL: 724CG ITEM NUMBERS: 21273-10, 21281-10 MODEL: 734CG ITEM NUMBERS: 21276-10, 21277-10 TO IDENTIFY MODEL AND ITEM NUMBER, SEE DATA TAG INSIDE FRYER. IMPORTANT The electrical diagrams in this manual are for models produced 2018 and later with an ‘Omron’...
Page 55 724G-1718_CV FOR 120V GAS FRYERS PAGE 2 OF 4 MODEL: 718LCG ITEM NUMBERS: 21263-10, 21264-10 MODEL: 724CG ITEM NUMBERS: 21273-10, 21281-10 MODEL: 734CG ITEM NUMBERS: 21276-10, 21277-10 TO IDENTIFY MODEL AND ITEM NUMBER, SEE DATA TAG INSIDE FRYER. IMPORTANT The electrical diagrams in this manual are for models produced 2018 and later with an ‘Omron’...
Page 57 724G-1718_CV FOR 120V GAS FRYERS PAGE 3 OF 4 MODEL: 718LCG ITEM NUMBERS: 21263-10, 21264-10 MODEL: 724CG ITEM NUMBERS: 21273-10, 21281-10 MODEL: 734CG ITEM NUMBERS: 21276-10, 21277-10 TO IDENTIFY MODEL AND ITEM NUMBER, SEE DATA TAG INSIDE FRYER. IMPORTANT The electrical diagrams in this manual are for models produced 2018 and later with an ‘Omron’...
Page 59 724G-1718_CV FOR 120V GAS FRYERS PAGE 3 OF 4 MODEL: 718LCG ITEM NUMBERS: 21263-10, 21264-10 MODEL: 724CG ITEM NUMBERS: 21273-10, 21281-10 MODEL: 734CG ITEM NUMBERS: 21276-10, 21277-10 TO IDENTIFY MODEL AND ITEM NUMBER, SEE DATA TAG INSIDE FRYER. IMPORTANT The electrical diagrams in this manual are for models produced 2018 and later with an ‘Omron’...
Page 61 724G-1719_CV PAGE 1 OF 4 FOR 208-240V GAS FRYERS MODEL: 718LCG ITEM NUMBERS: 21267-10, 21268-10 MODEL: 724CG ITEM NUMBERS: 21282-10, 21287-10 MODEL: 734CG ITEM NUMBERS: 21278-10, 21280-10 TO IDENTIFY MODEL AND ITEM NUMBER, SEE DATA TAG INSIDE FRYER. IMPORTANT The electrical diagrams in this manual are for models produced 2018 and later with an ‘Omron’...
Page 63 724G-1719_CV PAGE 2 OF 4 FOR 208-240V GAS FRYERS MODEL: 718LCG ITEM NUMBERS: 21267-10, 21268-10 MODEL: 724CG ITEM NUMBERS: 21282-10, 21287-10 MODEL: 734CG ITEM NUMBERS: 21278-10, 21280-10 TO IDENTIFY MODEL AND ITEM NUMBER, SEE DATA TAG INSIDE FRYER. IMPORTANT The electrical diagrams in this manual are for models produced 2018 and later with an ‘Omron’...
Page 65 724G-1719_CV PAGE 3 OF 4 FOR 208-240V GAS FRYERS MODEL: 718LCG ITEM NUMBERS: 21267-10, 21268-10 MODEL: 724CG ITEM NUMBERS: 21282-10, 21287-10 MODEL: 734CG ITEM NUMBERS: 21278-10, 21280-10 TO IDENTIFY MODEL AND ITEM NUMBER, SEE DATA TAG INSIDE FRYER. IMPORTANT The electrical diagrams in this manual are for models produced 2018 and later with an ‘Omron’...
Page 67 724G-1719_CV PAGE 4 OF 4 FOR 208-240V GAS FRYERS MODEL: 718LCG ITEM NUMBERS: 21267-10, 21268-10 MODEL: 724CG ITEM NUMBERS: 21282-10, 21287-10 MODEL: 734CG ITEM NUMBERS: 21278-10, 21280-10 TO IDENTIFY MODEL AND ITEM NUMBER, SEE DATA TAG INSIDE FRYER. IMPORTANT The electrical diagrams in this manual are for models produced 2018 and later with an ‘Omron’...
Page 69 Belshaw Adamatic Bakery Group Limited Warranty / Return Policy Subject to the terms and limitations set forth in this limited warranty (“Limited Warranty”), Belshaw Adamatic Bakery Group (also referred to as “the Manufacturer”) warrants to the original purchaser (“Purchaser”) of Manufacturer’s equipment and parts (“Products”), Belshaw Adamatic Bakery Group’s manufacture and assembly of Products to be free from defects in workmanship and material which would result in product failure under normal use and service.
Page 70 Warranty Claims In case of warranty claims relating to your Product, you must follow the instructions below. Report Claims to Your Authorized Distributor or Dealer or to Belshaw Adamatic Bakery Group As soon as you discover a problem, contact the Distributor or Dealer from whom you purchased the Product or Belshaw Adamatic Bakery Group.
Page 71 The #1 Source for Donut and Bakery Equipment www.belshaw.com BELSHAW ADAMATIC BAKERY GROUP 814 44th Street NW, Suite 103 Auburn, WA 98001 USA 1-800-BELSHAW 1-800-578-2547 (USA/Canada) (+1) 206-322-5474 (Worldwide) service@belshaw.com an Ali Group Company The Spirit of Excellence...

This manual is also suitable for:

724cg 734cg 21263-10 21264-10 21267-10 21268-10 ... Show all

Belshaw Brothers 718LCG Operator's Manual

Table of Contents

Preface

1 Operation

2 Cleaning

3 Donut-Making Helps

Table of Contents

Preface

1 Installation

2 Maintenance

3 Troubleshooting

4 Pilot Module

Quick Links

Chapters

Need help?

Questions and answers

Summary of Contents for Belshaw Brothers 718LCG

Page 4: Table Of Contents

Page 5: Preface

Page 6: Operation

Page 7: If The Pilot Light Fails To Ignite

Page 8: Fill Up To "Oil Level" Marks

Page 9: Cleaning

Page 10: Washing

Page 12: Donut-Making Helps

Page 13: Calculating Correct Water Temperature

Page 16: Preface

Page 17: Installation

Page 18: Unpacking The Fryer

Page 19: Installing The Fryer

Page 20: Moving The Fryer

Page 21: Mounting The Drain Tray

Page 22: Assembling The Frying Screen Handles

Page 23: Maintenance

Page 27: Troubleshooting

Page 28: Pilot Module

Page 29: Main Burner Operation

Page 31: Step 5: Check Normal Operation

This manual is also suitable for:

Belshaw Brothers 718LCG Operator's Manual

Table of Contents

Preface

1 Operation

2 Cleaning

3 Donut-Making Helps

Table of Contents

Preface

1 Installation

2 Maintenance

3 Troubleshooting

4 Pilot Module

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Belshaw Brothers 718LCG

Summary of Contents for Belshaw Brothers 718LCG

This manual is also suitable for:

Table of Contents