vacuubrand VAP 5 Instructions For Use Manual
Technology for vacuum systems, vacuum gauges
Hide thumbs
Also See for VAP 5:
- Instructions for use manual (17 pages) ,
- Instructions for repair (72 pages)
Advertisement
Documents are only to be used and distributed completely and unchanged. It is strictly the users´ responsibility to check
carefully the validity of this document with respect to his product. manual-no.: 999039 / 16/12/2009
page 1 of 17
Technology for Vacuum Systems
Instructions for use
VAP 5
DVR 5
Vacuum gauges
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for vacuubrand VAP 5
Summary of Contents for vacuubrand VAP 5
- Page 1 1 of 17 Technology for Vacuum Systems Instructions for use VAP 5 DVR 5 Vacuum gauges Documents are only to be used and distributed completely and unchanged. It is strictly the users´ responsibility to check carefully the validity of this document with respect to his product. manual-no.: 999039 / 16/12/2009...
- Page 2 2 of 17 Dear customer, Your VACUUBRAND vacuum gauge shall support you at your work for a long time without any trouble and with full load output. Thanks to our large practical experience we attained much information how you could add to an efficient application and to personal safety.
-
Page 3: Table Of Contents
page 3 of 17 Contents Safety information! ....................4 Technical data ......................6 Use and operation ..................... 7 Troubleshooting ...................... 10 Cleaning the gauge head ..................11 Readjustment ......................11 Calibration in the factory ..................13 Notes on return to the factory ................14 Health and safety clearance form ................15 Attention! Important notes! Not permitted! Misuse may cause damage. -
Page 4: Safety Information
☞ The product is equipped with a short circuit proof transformer with an integrated overload protection (no fuses). Operate the equipment only in combination with VACUUBRAND genuine accessories. Obey all other relevant safety requirements (e. g. accident prevention regulations for working in laboratories and explosion protection guidelines) and provide protective measures. - Page 5 page 5 of 17 Ensure that maintenance is done only by suitably trained and supervised technicians. Ensure that the maintenance technician is familiar with the safety procedures which relate to the equipment processed by the vacuum system and that the equipment if necessary is approximately decontaminated before starting maintenance.
-
Page 6: Technical Data
page 6 of 17 Technical data v i t < ) t i c i f f i c < ° 0 ° 0 ° 0 ° 0 ° 0 ° 0 ° 0 ° 0 ~, + ~, + "... -
Page 7: Use And Operation
page 7 of 17 Use and operation Display after switching on together with display ”CAL” adjustment mode (internal check and adjustment routine) warning symbol selectable pressure units Rear side rating plate serial interface (only DVR 5) mains switch key-button for digital adjustment and electronic scale conversion (pressure unit) - Page 8 Description VAP 5 The vacuum gauge VAP 5 relies on the fact that the thermal conductivity of the residual gas in the vacuum chamber is a measure for the gas pressure. The thermal conductivity of gases is proportional to the pressure within a certain range and is related to the molecular mass.
- Page 9 page 9 of 17 Interface parameters Interface parameters at the COM port have to be set as follows (the interface parameters at the DVR 5 cannot be changed): s t i s t i s t i y t i Via the interface the actual pressure value can be read out.
-
Page 10: Troubleshooting
page 10 of 17 Troubleshooting a l i i t c . r i , f f l i t i t c . r i " " r i t c i t c t l i i t c t l i , t l y l t... -
Page 11: Cleaning The Gauge Head
page 11 of 17 Instructions for repair with directions for repair and spare parts list is available on request. ☞ The instructions are for trained service people. Cleaning the gauge head The gauge itself is maintenance-free. ➨ ➨ ➨ ➨ ➨ Only VSP 5: Using small screw driver or pencil tip, release locking ring in gauge head connection and remove protective filter with shim, keep locking ring. - Page 12 page 12 of 17 Adjustment under vacuum: ➨ ➨ ➨ ➨ ➨ Evacuate gauge head to a pressure < 5 x 10 mbar. Status indication vacuum is displayed. Note: Adjustment under vacuum with an actual pressure > 5 x 10 mbar reduces the accuracy of the measurement.
-
Page 13: Calibration In The Factory
Calibration in the factory Control of measuring equipment The VACUUBRAND DKD calibration laboratory is accredited by the Physikalisch-Technische Bundesanstalt (PTB; German national institute for science and technology and the highest technical authority of the Federal Republic of Germany for the field of meteorology and certain sectors of safety engineering) for the... -
Page 14: Notes On Return To The Factory
page 14 of 17 Notes on return to the factory Repair - return - DKD calibration Safety and health of our staff, laws and regulations regarding the handling of danger- ous goods, occupational health and safety regulations and regulations regarding safe disposal of waste require that for all pumps and other products the “Health and safety clearance form“... -
Page 15: Health And Safety Clearance Form
Tel.: +49 9342 808-0 - Fax: +49 9342 808-450 -Technology for Vacuum Systems- E-Mail: info@vacuubrand.de © 2003 VACUUBRAND GMBH + CO KG Printed in Germany Web: www.vacuubrand.com Documents are only to be used and distributed completely and unchanged. It is strictly the users´ responsibility to check... - Page 16 Vakuum-Controller / Vacuum controller / Régulateur de vide DVR 5 (230V; 682910, 682911, 682912) VAP 5 (230V; 682850, 682858, 682881, 682880) Hiermit erklären wir, dass das oben bezeichnete Gerät in Konzeption und Bauart sowie in der von uns in Verkehr gebrachten Ausführung den grundlegenden Anforderungen der zutreffenden, aufgeführten EU- Richtlinien entspricht.
- Page 17 Tel.: +49 9342 808-0 - Fax: +49 9342 808-450 -Technology for Vacuum Systems- E-Mail: info@vacuubrand.de © 2009 VACUUBRAND GMBH + CO KG Printed in Germany Web: www.vacuubrand.com Documents are only to be used and distributed completely and unchanged. It is strictly the users´ responsibility to check...
Need help?
Do you have a question about the VAP 5 and is the answer not in the manual?
Questions and answers