Advertisement

Synel Americas
480-37 4-7700
8665 E Hartford Dr Suite 100
www.synel-americas.com
sales@synel-americas.com
Scottsdale, AZ. 85255
V Feb 2020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 785 and is the answer not in the manual?

Questions and answers

Summary of Contents for Synel 785

  • Page 1 Synel Americas 480-37 4-7700 8665 E Hartford Dr Suite 100 www.synel-americas.com sales@synel-americas.com Scottsdale, AZ. 85255 V Feb 2020...
  • Page 2: Technical Specifications

    (1 too many). The terminal utilizes a high resolution 500 dpi finger template. External Readers: The TA-785 has two reader ports to connect external devices such as a Bar code Gun or an Access Control Swipe Reader that could be mounted outside a door.
  • Page 3: Internal Components

    Host – RS-232 / RS-485 Communications 1.4 Internal Components The TA-785 has two back-up battery modules, one for the real time clock memory and the other for operation during a power failure. The standard memory back-up module is a lithium battery, which will keep the internal clock running and the memory intact, for 30 days during a power failure.
  • Page 4 During a power failure, the user presses the battery key to activate the terminal. Data can then be entered and stored in the TA-785 memory. The time-out will cause the terminal to shut down automatically after the last use of the terminal, until the battery key is pressed again.
  • Page 5: Unpacking And Installation

    Note: Do not throw away the box or packing materials. Check the box and the contents for any signs of damage that may have happened during shipment. Carefully unpack and check the contents. The TA-785 package contains: 1 TA-785 terminal Mounting panel/back plate 10 meter serial cable.
  • Page 6: Mounting The Terminal

    2.2 Mounting the Terminal Make sure the unit is unplugged and that it is not connected to the network/PC. Caution: The terminal should not be mounted where it will be exposed to extreme heat or cold, water, steam, violent vibrations, high electromagnetic radiation including high voltage power lines and electrical equipment.
  • Page 7: Terminal Configuration

    3.0 Terminal Configuration The TA-785 Terminal can be connected to the host computer using either RS-232(Direct), RS-485(LAN), Ethernet including Wi-Fi or Modem connections. 3.1 Entering Technician Mode The TA-785 Terminal contains a built in configuration program called Technician mode.
  • Page 8: Communication And Configuration

    The terminal can be connected to one of the following communication networks: Ethernet (optional card) - For this type of communication, an IP address is defined for every TA-785 terminal, enabling communication with each terminal in any 10/100 Ethernet network.
  • Page 9: Network Connection

    FPU - Setting the fingerprint unit mode 3.3.1.1 RS-232 Connection The TA-785 terminal can be connected to the host computer via RS-232 with the DB9 Serial Adapter and a serial cable. The maximum supported cable length for the serial cable is currently 50’.
  • Page 10 3.3.3 Ethernet Settings For this type of communication an IP address is defined for every TA-785 terminal enabling communication with each terminal in any 10/100 Ethernet network. Unless otherwise noted, the default settings in bold on the right should always be used.
  • Page 11 Baud rates are: 1200, 2400 and 4800, 9600 and 19200 • Adjust station ID: The Station ID is the TA-780/785’s unique identifier for multi-terminal communication. Any number from 0 to 31 may be used as the ID, but it must match the ID in the software. •...
  • Page 12 • Set/Reset/Exit: Select S to continue and setup the Wi-Fi settings.  Reset Use this menu to reset the Wi-Fi card and to change the password.  Exit Use this menu option to exit out of the Network Connection settings. ...
  • Page 13 User Name  User Password  • WPA PSK: Set by drilling down and selecting the parameters.  WEP PSK Password – enter password.  TKIP  WEP PSK Password – enter password.  CCMP  WEP PSK Password – enter password. ...
  • Page 14: Terminal Maintenance

    4.0 Terminal Maintenance 4.1 Recovery from Memory Error MEM CRASH If there is a memory error, a message will appear on the terminal screen. You will need to clear the NO PROG terminal’s memory and return the terminal to the (No Programming) state according to the procedure below.
  • Page 15 5.0 Field Upgrades and Servicing One of the many features of the TA-785 terminal is the ability to do field upgrades and servicing. This section provides an explanation on how to perform the following upgrades: • Internal Ethernet Card installation •...
  • Page 16 Line up the pins to the connectors on the board. Slide the pins into the connectors until the board rests on the two screw mounts. Use the image below as a reference for proper card placement. Type B Type F Insert the two screws for the Ethernet card.
  • Page 17 5.3 Procedure – Internal Wi-Fi Card Installation NOTE: Refer to the section 3.3.4 for additional information on configuration settings for this option. Unplug the power cord from the bottom of the Terminal and allow the unit to shut down after the battery backup takes over.
  • Page 18: Main Power Connector

    5.4 Procedure – POE Card Installation Warning: These functions should only be performed by qualified personnel only. It requires working with an open unit. Make sure to unplug the unit wherever the instructions call for it. Failure to take the proper precautions may result serious injury or death.
  • Page 19 Remove the main board from the unit. Remove the screws from the plastic protection cover on the power board. Warning: Be very careful when handling the power board, failure to take proper precautions may result in serious injury or death. Remove the power cable by loosening the 3 screws for the black, white and green wires and pulling them from the connectors.
  • Page 20 5.5 Procedure – Finger Reader Installation Unplug the power cord from the bottom of the Terminal and allow the unit to shut down after the battery backup takes over. This will last about 20 seconds. Unscrew and remove the front panel; there are 5 screws on the back side of the terminal. Pop out and replace the plug with the holder for the finger reader.
  • Page 21 5.6 Procedure – Proximity Reader Installation Unplug the power cord from the bottom of the Terminal and allow the unit to shut down after the battery backup takes over. This will last about 20 seconds. Unscrew and remove the front panel; there are 5 screws on the back side of the terminal. Using the image below as a guide, attach the proximity reader into the unit using the two screws that came with the kit.
  • Page 22 The Setup should now look like the image below. Replace the front panel, insert the screws inserting the 5 screws and being careful not to over tighten them. Plug the Terminal back into a power source and make sure that the date/time appears in the terminal display - 21 -...
  • Page 23: Supervisor Mode

    Appendix – A Supervisor Mode You can assign multiple badge numbers to enter into Supervisor mode, but you cannot use these numbers to clock in with. A.1 Enrolling Employees into the Terminal NOTE: The clock is programmed initially with a supervisor badge of 11111. This badge number will normally be cleared the first time you program the clock if you use different badge numbers or badge lengths for supervisors.
  • Page 24 NOTE: Do not use [CLEAR] to go back in the menus, or to exit out of supervisor mode. This may clear out what changes or additions you made in supervisor mode. A.1.2 Deleting an Employee Template from the terminal Use the following steps to remove a user from the terminal. Step 1.
  • Page 25: Diagnostics Mode

    A.2 Adding Transactions Use the following steps to add transactions into the terminal: NOTE: The clock is programmed initially with a supervisor badge of 11111. This badge number will normally be cleared the first time you program the clock if you use different badge numbers or badge lengths for supervisors.
  • Page 26 Appendix – B Proximity Setup B.1 Setting up the Proximity Reader The proximity reader has the opportunity to read the badges several different ways depending on the badge type. Use the following steps to setup the clock to identify the badge. Step 1.
  • Page 27: Error Message

    Appendix – C Error Messages Code Error Message UNKNOWN ERROR NO FINGER DETECT FPU IS BUSY SUCCESS SCAN SUCCESS SCAN FAILED TMPL NOT FOUND TMPL NOT MATCHED TRY AGAIN TIME OUT FPU MEMORY FULL USER ID EXISTS CHECK USER ID ADD NEW TEMPLATE OVR FINGER LIMIT CONTINUE...
  • Page 28: Internal Wiring Diagrams

    Appendix – D Internal Wiring Diagrams D.1 Bells and Access D 1.1 Signal Control With the TA-780’s internal relay, the terminal can control a 30 VDC, 1 Amp dry-contact circuit. The signal control relay can be turned on by both a specific employee badge/number for access control or by time of day for bell ringing.
  • Page 29 Appendix – E External Wiring Diagrams E.1 RS-232 RS-232 uses the DB9 Serial Adapter and a serial cable. Note: Supported distances for cabling is currently 50 feet. - 28 -...
  • Page 30: External Connectors

    Appendix – E External Connectors HOST RJ-45 (8-pin) RS-232 Signal Value Remarks RS-485 (-TRX) 0-5 Volt RS-485 (+TRX) 0-5 Volt RS – 232 (TXD) -/+15Vdc Standard RS-232 levels RS – 232 (RXD) -/+15Vdc Standard RS-232 levels RJ-45 (8-pin) Ethernet Signal Value Remarks Transmit data...
  • Page 31: Barcode Reader

    Barcode Reader Signal Value Remarks Data(-) For RS-422 Led 1 Led 2 Led 3 DATA Data +, For RS – 422 - 30 -...

Table of Contents

Save PDF