Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Summit Commercial BIM100
Summary of Contents for Summit Commercial BIM100
- Page 1 100LB. ICE MACHINE User Manual MODELS: BIM100, SCIM101, ALIM100 Felix Storch, Inc. Summit Appliance Division Write Serial No. of unit here: An ISO 9001:2015 registered company 770 Garrison Avenue Bronx, NY 10474 ________________________________ www.summitappliance.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Important Safety Instructions Precautions Grounding Instructions Location of Parts Installation Instructions Before Using your Ice Maker Installing the Ice Maker Connecting the Water Line Installing the Purification Filter Operation Ice Full Sensor Ice Thickness Sensor Changing the Purification Filter Cleaning Cleaning the Ice Bin Cleaning the Condenser Filler... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION BEFORE USING. WARNING: RISK OF CHILD ENTRAPMENT Child entrapment and suffocation are not problems of the past. Unused or abandoned icemakers are still dangerous, even if they will just “sit in the garage a few days.” •... -
Page 4: Grounding Instructions
GROUNDING INSTRUCTIONS WARNING: Improper use of the grounding plug can result in a risk of electric shock. • This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. •... -
Page 5: Location Of Parts
LOCATION OF PARTS (Front) (Rear) (Interior) -
Page 6: Installation Instructions
INSTALLATION INSTRUCTIONS Before Using the Ice Maker • Remove any exterior or interior packaging. • Attach the four leveling feet to the bottom of the appliance. NOTE: Before connecting the ice maker to a power source, let the appliance stand upright for approximately two hours. -
Page 7: Installing The Purification Filter
• Connect a 3/8” diameter pipe to the tap water line. • The pressure of the tap water line should be maintained at a level between 20psi (1.4bar) and 80psi (5.5bar). The tap water line and drain pipeline should be planned and prepared at the place of installation. -
Page 8: Changing The Purification Filter
Changing the Purification Filter When the purification filter is no longer active, the ice maker will not produce ice. The filter cycle is typically 6 months, but might be shorter, depending on your environment and quality of your water. Replacement filters can be ordered online at summitappliance.com/filter100. To change the filter: 1. -
Page 9: Cleaning The Condenser
Cleaning the Condenser 1. Unscrew the two screws at the bottom of the front panel. 2. Pull down on the front panel to separate it from the appliance. 3. Use a vacuum cleaner to remove dust from the condenser. 4. After cleaning, insert the front cover into the upper holes, and push up and into place. -
Page 10: Troubleshooting
When the first sanitizing procedure is complete, remove the packing down from the ice basin by pulling downward. Remove the water inside the packing down, and insert it back into the ice vessel sheet. Conduct the sanitizing procedure two more times. Once the third sanitizing procedure is complete and all of the components have been reinstalled, set the power switch to the “ICE”... -
Page 11: Technical Specifications
TECHNICAL SPECIFICATIONS Specification Item Unit BIM100, SCIM101, ALIM100 Maximum Ice Making Kg /day 50(110.2) (Based on 10 ℃ ) (Lbs./day) Freezing Capability Ice is made after 30 minutes. Depth 574(22.5) Size mm(inch) (Installed Width 520(20.4) Height) Height 862(33.9) (FOOT included) -
Page 12: Limited Warranty
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship.
Need help?
Do you have a question about the BIM100 and is the answer not in the manual?
Questions and answers