Advertisement
Advertisement
Related Manuals for Valley-Dynamo All Star Baseball
Summary of Contents for Valley-Dynamo All Star Baseball
- Page 1 O_00011026 - 1 - Mar2018 Revision...
-
Page 2: Table Of Contents
13 – Game Play 14 – Game Parameters 16 – Selected Parts Listing For additional Technical Assistance: Email anytime: techhelp@valley-dynamo.com During business hours (Central US Time): call 972.595.5300 and follow the prompts for Tech support - 2 - Mar2018 Revision... -
Page 3: Warranty
DEALERS AND DISTRIBUTORS – To obtain replacement and an RMA number, contact Valley-Dynamo referencing the Model number and Serial number of the unit and the nature of the problem. Valley-Dynamo will, at its discretion, send replacement parts and/or issue an RMA for the return of failed parts. To avoid billing issues, request an RMA when the failed part is present or readily available. - Page 4 EXCLUSION OF DAMAGES Valley-Dynamo’s sole obligation and liability under this warranty is limited to the repair or replacement of a defective product at our option. Valley-Dynamo shall not, in any event, be liable for any incidental or consequential damages resulting from interruption of service, loss of business or revenue, or for liability in tort relating to this product or resulting from its use or possession.
-
Page 5: Assembly Instructions
Assembly Instructions 1) Position the box as shown in the photo. Not surprisingly, with the arrows pointing upward and the word “TOP” at the top of the box. Remove the lid… 2) …slide the corner protectors up and remove them from the box. - Page 6 3) The box can then be lifted up. Save the box for use as a protective surface to avoid scratching your All Star Baseball unit as it is being assembled. BACK BOX So we are all in agreement on the names of what’s in the box….
- Page 7 5) Remove the legs from the parts box. Each leg should have a leveler installed (if not, install it at this time). Make sure each leg leveler is adjusted to its highest position and screwed “all the way in”. 6) While the Lower Cabinet is still in the upright position, install the two front legs using two 5/8”...
- Page 8 8) …and use the parts box to prop up the cabinet so you can install the rear legs. As with the front legs, the leg bolts will be found installed in the cabinet. Remove the bolts, secure the legs, reinstall and fully tighten the bolts.
- Page 9 Connect the cables from the Back Box to the Lower Cabinet using the color-coordinated markings on each connection. Route the cables so they do not interfere with the base- runner mechanism. The CAT5 network cable from the lower cabinet should be connected to the I/O Board as shown.
- Page 10 To add the balls to the unit, first open the coin door and loosen the latch inside the coin door that secures the control panel Lift the control panel straight up, and then pivot the upper portion toward you, away from the cabinet. - 10 - Mar2018 Revision...
- Page 11 With the control panel pivoted back, you can now slide the game glass gently towards you to open up a gap at the top, just below the back box. Providing enough room to gently place the balls onto the playfield. Reverse the process by sliding the game glass back into place, replacing the control panel,...
- Page 12 Install the power cable and plug in the unit into a grounded, surge-protected outlet. Turn on the power switch located beneath the right front corner of the Lower Cabinet. If there are no problems, you can replace the rear door on the back box.
-
Page 13: Game Play
Game Play COIN PLAY: Insert coins or bills (with optional Bill Acceptor) as indicated on the instruction card. Credit is indicated by the lamp in the backbox. FREE PLAY : Set using parameters on page #15 1 and 2 player start button will illuminate when credit is available. SINGLE PLAYER GAME: Player pushes any lit “pitch”... -
Page 14: Game Parameters
Game Parameters See the following table for the settings that can be changed. Settings are stored in flash memory, so settings are saved even when the power is off. To change settings for the game use the following steps: 1. Open the coin door, the setting are changed with these four buttons located inside the cabinet to the left. - Page 15 Number Setting Default Notes High Score Home Run Derby Balls 1 through 49 Innings per Game Range 1-99. Greater number is Bat coil strength stronger Range 1-99. Greater number is Curve Magnet strength stronger Credits per game 0 = free play Features Attract Delay x 8 = seconds, 0 through 15...
-
Page 16: Selected Parts Listing
Selected Parts List part # description BASE-860200000 BUTTON - CHANGE UP BASE-860200010 BUTTON - CURVE BALL BASE-860200020 BUTTON - FAST BALL BASE-860200030 BUTTON - 1 PLAYER BASE-860200040 BUTTON - 2 PLAYER BASE-860200050 BUTTON - SELECT GAME BASE-860200060 BUTTON - BAT BACKGLASS, PRINTED (ALL AMERICAN) –... - Page 17 Star and Zombie League All Star Games measures 32 ⅛” x 22 ¾” x 3/16” thick In most cases it will be more economical to source this TEMPERED glass locally than to have it shipped from Valley-Dynamo. - 17 - Mar2018 Revision...