Related Manuals for Sony DEP-100
Summary of Contents for Sony DEP-100
- Page 1 DIGITAL EFFECTS PROCESSOR DEP-100 INSTALLATION MANUAL 1st Edition Serial No. 10001 and Higher...
- Page 2 ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
-
Page 3: Table Of Contents
Information of LEDs on Board ............. 2-2 (E) 2-4. ISR ......................2-3 (E) 2-4-1. Functions Overview ............. 2-3 (E) 2-4-2. Usage of ISR Functions ............2-3 (E) 2-4-3. Supported Commands ............2-4 (E) 2-4-4. Functions of Commands ............2-4 (E) 1 (E) DEP-100... -
Page 4: Manual Structure
Manual Structure Purpose of this manual This manual is the installation manual of the DEP-100 Digital Effects Processor. This manual is intended for use by trained system and service engineers, and describes the information regarding installation. Contents The following is a summary of all the sections for understanding the contents of this manual. -
Page 5: Installation
0.5 A (at 240 V) A switching regulator is used for the power supply of the DEP-100. The voltage within the range of 100 V to 240 V Power cord for the customer in Europe except the can be used without changing the supply voltage. -
Page 6: External Dimensions And Installation Space
To prevent the temperature rise inside the DEP-100, pay careful attention to circulation of air in the place where the DEP-100 is installed. The rear side of the DEP-100 should be at least 20 cm away from walls for ventilation and maintenance. Mass : 13.5 kg 866.2... -
Page 7: Matching Connectors And Cables
When connecting cables to various connectors on the rear panel at the time of installing or servicing, connect the following connectors/cables or their equivalents. DEP-100 Matching Connector/Cable Panel indication Connector/cable Sony Part No. ANALOG I/O BNC 75 Z, male 1-560-069-11 REF.VIDEO MONITOR OUT... -
Page 8: Input And Output Signal Of Connector
TTL Level, 10 k Z Output Connector 2 MONITOR OUT BNC x 1 Analog composite video 1.0 V p-p, 75 Z, sync negative 3 PROGRAM OUT BNC x 4 Component digital (270 Mbps) Conform to SMPTE 259M & ITU-R BT.656 1-4 (E) DEP-100... - Page 9 D-sub 9-pin connector (RS-232C interface) Mouse control 8 ISR D-sub 25-pin connector (RS-232C interface) For ISR (Interactive Status Reporting) 9 REMOTE-OUT D-sub 9-pin connector (RS-422A interface) Remote control !/ REMOTE-IN D-sub 9-pin connector (RS-422A interface) Remote control 1-5 (E) DEP-100...
- Page 10 RTS; Request to Send (Output) CTS; Clear to Send (Input) SPARE DSR; Data Set Ready (Input) Signal Ground RM TX (+) DCD; Data Carrier Detect (Input) RM RX (_) 9 to 19 DTR; Data Terminal Ready (Input) 21 to 25 1-6 (E) DEP-100...
-
Page 11: Switch Setting On Connector Panel
1-7. Switch Setting on Board 1-6. Switch Setting on Connector Panel 1-7. Switch Setting on Board Be sure to set the following switch when the DEP-100 is installed. There is no switch on the SEC-54 and VSW-61 boards. 75 Z Z Z Z Z termination switch of REF. VIDEO INPUT... -
Page 12: Rack Mounting
1-8. Rack Mounting For the switches described “Unassigned” and “Factory use” , do not change the factory settings. The DEP-100 can be mounted in a 19-inch standard rack. S700-1: Unassigned To prevent falling the rack, fix it on the horizontal firm S700-2, -3: Factory use floor with bols. - Page 13 1-8. Rack Mounting 4. Attach the inner rails to the DEP-100 using the six Procedures screws (B4 x 8) supplied with the DEP-100. 1. Turn the power off. 2. Remove the four feet from the bottom of the DEP-100. Inner rail...
- Page 14 Height of the unit mounted in rack Outer rail Stopper Inner rail . Be sure to mount the DEP-100 in the rack with two or more persons. Trying to handle this job by one-person could occur to injury. . Be careful not to get caught your hand and finger in the rack mount rail when installing the unit in the rack.
-
Page 15: Service Overview
. Filter (3U): 3-608-795-01 6. After cleaning, fasten the filter to the tapes. 2-2. Periodic Replacement If the DEP-100 is kept on operating with too dusty of the filter, the temperature inside the unit getting rise. This may cause a fire. -
Page 16: Information Of Leds On Board
Factory use D703 to D706 (red) (A-10): Unassigned A Side(Component side) D707 (red) (A-10): SYSTEM CONTROL ERROR indicator Lights up when CPU does not run normally. D708 (green) (A-11): SYSTEM CONTROL STATUS indicator Blinks when CPU runs normally. 2-2 (E) DEP-100... -
Page 17: Isr
Reporting) function. tion of a personal computer in which this program software Using this function, the status of the DEP-100 and the can be used, please consult with your local Sony’s sales/ contents of a generated error can be intensively monitored service office. -
Page 18: Supported Commands
The DEP-100 supports the following commands. For more detailed information of each command, refer to This command is used to reset the ISR processor (soft- the ISR PROTOCOL manual. ware). When reset processing is complete, the DEP-100 returns Common Command Description “*ATN: OPC;”. *RST;... - Page 19 This command response to “*IDN?” command. requests the contents of the command error buffer. When the setting is complete, the DEP-100 returns “*ATN: OPC;”. LDSW TYPE; module (Load Software) This command is used to download the software module.
- Page 21 The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any...
- Page 22 Printed in Japan Sony Corporation DEP-100 (SY) J, E 1997. 10 08 Broadcast Products Company 3-193-433-01 ©1997 Published by Broadcast Products Company...