Advertisement
Quick Links
1
Installation Instructions for 41492
2D Analog 6 Gauge Panel Kit w/Chrome Billet
* Always disconnect the battery before attempting any electrical work on your vehicle. *
KIT COMPONENTS
◊ One (1) Assembled Analog Circuit Board (with Speedometer, Tachometer, Voltmeter, Water
Temp., Fuel Level and Oil Pressure Gauges – with lens and two attached mounting
brackets.
◊ One (1) Temperature Sending Unit (41690)
* 1/8" NPT, 0-255 Deg., 1/2" NPT Bushing
◊ One (1) Pressure Sending Unit (41608)
* 1/8" NPT, 0-100 PSI Oil Pressure
◊ One (1) Universal Speedometer Sensor (41610)
* 7/8" NPT Industry Standard threads
PANEL MOUNTING INSTRUCTIONS
Carefully remove existing gauges. You may need to alter the dashboard in your vehicle to accommodate
this new Analog panel. Remove the two mounting brackets from the back of the new panel and reinstall
them on the backside of your vehicle's dashboard.
WIRING INSTRUCTIONS
Note: Automotive circuit connectors are the preferred method of connecting wires. However, you may
solder if you prefer.
Ground – Black--This is the main ground for the display system. A wire should be run from this
board to the vehicle engine block for the best ground. Use 18 or 14 AWG or larger wire to ensure
sufficient grounding. Proper vehicle grounding is extremely important for any gauges (or electronics) to
operate correctly. The engine block should have heavy ground cables to the battery, frame, and firewall.
Failure to properly ground the engine block, senders, or digital dash can cause incorrect or erratic
operation.
Power – Pink--Connect the power terminal to accessory +12V power from the fuse panel or vehicle wiring
harness. Using a 5-amp fuse or an inline 5-amp fuse holder. This terminal should have power when the key
is on or in accessory position. Use 18 AWG wire to ensure the system receives a sufficient power feed.
Power - Red--Connect the power terminal to accessory +12V power from the fuse panel or vehicle wiring
harness. Using a 5-amp fuse or an inline 5-amp fuse holder This terminal should have power when the key
is on or in accessory position. Use 18 AWG wire to ensure the system receives a sufficient power feed.
1-800-345-4545 jegs.com
Advertisement
Related Manuals for Jegs 41492
Summary of Contents for Jegs 41492
- Page 1 Installation Instructions for 41492 2D Analog 6 Gauge Panel Kit w/Chrome Billet * Always disconnect the battery before attempting any electrical work on your vehicle. * KIT COMPONENTS ◊ One (1) Assembled Analog Circuit Board (with Speedometer, Tachometer, Voltmeter, Water Temp., Fuel Level and Oil Pressure Gauges –...
- Page 2 UPSIDE DOWN! Both switches in the ON position for Ford/Chrysler For GM - #1 toggle is ON # 2 toggle is OFF. Both switches in the OFF position for VDO For Universal/Stewart Warner #1 toggle is OFF 1-800-345-4545 jegs.com...
- Page 3 (we prefer this to be high output). The other wire (Low output) Ground at the Engine block. To find High and Low output wire color or pin location will need to be looked up by Vehicle vin or Model and year or (Consults Pinout Chart). 1-800-345-4545 jegs.com...
- Page 4 Speedometer - White (JEGS- Speed Sender) - Disconnect the mechanical speedometer cable from the transmission and thread the new electronic sensor onto the transmission. This panel comes with a 3-wire sensor. If you are using this sensor, the white wire is the speed signal; connect this to the speed signal wire on your gauge.
- Page 5 However, once it finishes scrolling one time, the memory is ready to record new data and will begin recording again once the vehicle starts to move. The highest speed measured over multiple runs will be retained in memory. 1-800-345-4545 jegs.com...