LINK light turn-on if the air system connect to air system. HDMI monitor instruction (if installed the HDMI monitor). The monitor shows logo "R2TECK" after ground system connect to the power. After that, the monitor shows progress bar: Start-up / Selfcheck / Link.
Page 4
Wait ground system MOBILE light turn off. Repeat the above 4 steps. IOS App installation: In App store, search the key word “r2teck” and download. Figure1.1.3.1 Connection diagram Attention:When used the ground system is fixed on the ground,its not a portable device.
无锡人人行拍网络科技有限公司 2. Specification Here list the detailed specification about DVLC , as shown in Table 2.1.1. Table 2.1.1List of Parameters Performance Parameter 100mw ground distance ≥ 800m 500mw ground distance ≥ 3000m (double distance in air) Communication distance If change to the wide angel directional patch antenna, the (outdoor, no obstruction) distance will be double.
DVLC use for wireless Full-HD Digital Video transmission. 3.4 Caution The effectiveness of DVLC use is subject to if comply with operate and maintain direction in this manual. Before operating the product, the staff must make sure the operate process and condition is correct.
Page 7
DVLC should not work when it is wet. Have to make sure it is dry when you use it.It should be dried immediately at a ventilated place in case of accidentally wet.
DVL it transmit the video, image and more information by the wireless communication mode. DVLC is perfect for all fields video transmission because of the light weight, low power, long distance, low latency. Please for all fields video transmission because of the light weight, low power, long distance, low latency.
Page 9
无锡人人行拍网络科技有限公司 4.2.2 Air system cable Air system power cable x 1 (standard) Air system power cable x 1 (standard) Air system power cable 12V 4.2.3 Ground system cable Power adapter x 1 (optional) Vehicle power 12V-DC for ground DC for ground system HDMI cable x 1 (optional) Monitor HDMI cabe...
无锡人人行拍网络科技有限公司 5. Port definition 5.1 Air system port 5.1.1 Back side Figure 5.1.1.1 schematic diagram of back side [1]: REClight,mp4 video recording status light Description Operation Light status The recording function is on Turn-on and the recording status is normal. Turn-off The recording function is off.
Page 11
无锡人人行拍网络科技有限公司 connected ground 2.Make sure the air system is system. connected the power; 3.Bind the air system and ground system again; 4. Connect the power again. [4]: POWERlight, Indicate the power supply state of the air system, and the description of each state is as follows.
Page 12
无锡人人行拍网络科技有限公司 [2]: OSD port,When it is necessary to display the OSD information of the flight control system, connect to the data line port of the flight control system for reading OSD information. 5.1.3 Right side port Figure 5.1.3.1 Schematic diagram of right side port [1]: OSD port,When it is necessary to display the OSD information of the flight control system, connect to the data line port of the flight control system for reading OSD information.
无锡人人行拍网络科技有限公司 5.2 Ground system port 5.2.1 Bottom side port Figure 5.2.1.1 schematic diagram of bottom side port [1]: Battery port, For connect with 2S/3S battery. [2]: Fix hole, For fix the ground system on the tripod. [3]: DC power port, For ground system to connect with the DC power, suggest output power is more than 1A.
Page 14
无锡人人行拍网络科技有限公司 Connect the system to the Connect the system to the The ground system does not The ground system does not Other status power again, or contact with power again, or contact with work. the customer service. [3]:Link light,For monitor the status of connect with the monitor the status of connect with the air system.
Page 15
无锡人人行拍网络科技有限公司 5.2.4 Front side port Figure 5.2.4.1 schematic diagram of front side port Figure 5.2.4.1 schematic diagram of front side port [1]: Air vent: Pay attention to not cover the Air vent: Pay attention to not cover the air vent.
无锡人人行拍网络科技有限公司 6. Installation 6.1 Air system installation 6.1.1 Antenna installation Ø Take out two pcs air system antenna. Ø Install them on the air system antenna holes, when you hear a clicking sound indicates completion of installation. Attention: For better transmit result, please make sure the antenna be away from the metal and carbon fiber frame, avoid being blocked by the main body of the aircraft or batteries, antenna should be vertical to the ground.
Page 17
无锡人人行拍网络科技有限公司 Figure 6.2.1.1 schematic diagram of ground system antenna installation schematic diagram of ground system antenna installation 6.2.2 HDMI cable installation One end of HDMI connect to the monitor, the other end of HDMI connect to the ground system. One end of HDMI connect to the monitor, the other end of HDMI connect to the ground system. One end of HDMI connect to the monitor, the other end of HDMI connect to the ground system.
无锡人人行拍网络科技有限公司 7. Bind Function description: Restores the device to factory settings, bind one air system with one ground system and gives the pairthe matching ID code. Operation method: the device LED light shows correctly, press two BIND buttons on air system and ground system together and keep more than 5 seconds, all the LED light turn off, release the button.
无锡人人行拍网络科技有限公司 8. Troubles solution Below is the device maintenances about DVLC, to help the users whom don't have professional testing device and technology to solve the simply troubles. 8.1 Trouble symptoms / diagnosis / solution Table 8.1.1Troublediagnosis and solution Symptoms...
Page 20
无锡人人行拍网络科技有限公司 HDMI cable Change a new HDMI cable. problem Video pause allowed Back to the allowed distance. distance display OSD cable is bad connected. Reconnect OSD cable of the ground system. abnormal Flight control Calibrate the flight control power voltage in battery voltage Power supply is uncalibrated.
无锡人人行拍网络科技有限公司 9. Appendix 9.1 Monitor OSD content Beside the video, on the top side and bottom side of the monitor display the OSD data. Beside the video, on the top side and bottom side of the monitor display the OSD data. Beside the video, on the top side and bottom side of the monitor display the OSD data.
Thanks for purchasing our device again. If you have any suggestion or need technical support, please visit our website or send us the email, also welcome to call us. Wuxi R2TECK Co., Ltd Address:Room307,Building of Cetus,Wuxi software park,111th Linghuavenue,new district ,Wuxi city,Jiangsu Province P.C.:214000...