Page 13
Jeder Endpoint wird durch seine interne EoC MAC-Adresse identifiziert, die nur innerhalb des Ethernet over Coax-Netzwerks gültig und für die angeschlossenen Ethernet-Geräte unsichtbar ist! ∂ ∂ ∂ ∂ ∂...
Page 16
IPv4/6 Link ∂ ∂ ∂ ∂ RADVD: IPv6-Einstellung wird von einem RADVD Server angefragt 1. TFTP-Parameter zur automatischen Konfiguration von NMU,Master und EP 2. Automatische Aktualisierung der EP Treiber aktivieren/deaktivieren...
Page 20
Link leuchtet grün – EP bereit Link leuchtet gelb – EP wird konfiguriert Link leuchtet rot – EP nicht erkannt / Konfiguration fehlgeschlagen Link ist grau – EP ist abgeschaltet Hintergrund in Pink – unzulässiger EP...
Page 21
Hintergrund in gelb – neuer Treiber für Aktualisierung Speichern aktueller Einstellungen des Masters/aktuellen EP/Standard-EP Benutzerdefiniertes EP-Standardprofil Löschen des veralteten EP-Profils Link Del EP...
Page 28
Betriebsanleitung | EoC 10-01 | Ethernet over Coax | Master 3.10. EP-WiFi-Einstellungen Konfiguration der WiFi-Eigenschaften des WiFi-EP-Geräts. 3.10.1. Einrichtung Netzwerk TCP/IP (WIFI:NET) Konfiguration der TCP/IP-Eigenschaften. Betriebsart: Bridge (Static IP) Im Auslieferungszustand ist der statische Bridge-Modus des EP aktiviert und der EP hat eine IP-Adresse aus Nullen (0.0.0.0).
Page 29
WIFI-Dienst Client-Isolierung (AP Isolation) Start-Betriebsart (Einzel-SSID,Multi-SSID und Multi-SSID mit VLAN) ∂ ∂ ∂ Beachten Sie, dass „Multi-VAP“ nur in der Betriebsart „Bridge“ und nicht in der Betriebsart „NAT „ funktioniert. Funk-Betriebsart Maximale TX-Leistung ∂ ∂ ∂ ∂ Kanal SSID verbergen...
Page 30
Nur in der Betriebsart Bridge möglich! SSID Sicherheitsbetriebsart (Security Mode) ∂ ∂ ∂ WiFi Sicherheitsschlüssel (Pre-Shared Key) VLAN ID WPA-Einstellung RSSI (Signalstärke) ∂ ∂ ∂ WIFI...
Page 31
RECFG Online-Diagnose – zwischen Master und EP...
Page 58
IPv4 Link: Off or Static or DHCP IP/Subnet Mask/Default Gateway/DNS IPv6 Link: Off or Static or DHCP or RADVD DHCP Option 82 and Snooping 1. TFTP Parameters to Auto Config NMU/Master/EP *.nmu *.dev 2. Enable/Disable Auto Upgrade of EP's EoC/WiFi Driver...
Page 62
Link in Green – EP is ready Link in Yellow – EP is being configuring Link in Red – unrecognized/configure-failed EP Link in Gray – EP is power off Background in Pink – banned EP Host Limit...
Page 63
Background in Yellow – new driver to upgrade Store current Master/current EP/default EP settings User Defined EP Default Profile Delete the Obsolete EP Profile Link Del EP...
Page 70
Operation Instructions | EoC 10-01 | Ethernet over Coax | Master 3.10. EP WiFi Settings To configure the WiFi properties of WiFi EP device. 3.10.1. Network TCP/IP Setup (WIFI:NET) Configure TCP/IP properties. Operation mode: Bridge (Static IP) Default is Bridge mode and EP has null IP Address (0.0.0.0). EP works as WLAN Access Point (AP) Bridge. May assign IP/Subnet Mask to WiFi interface if preferred.
Page 71
WIFI Service Client Isolation (AP Isolation) Start Mode (Single SSID/Multi-SSID/Multi-SSID with VLAN) ∂ ∂ ∂ Radio Mode Maximum TX Power ∂ ∂ ∂ ∂ Channel Hide SSID...