Advertisement
Quick Links
INSTALLATION GUIDE
NI PXI-2585/2586
Connector and Backshell Kit
Introduction
Caution
When hazardous voltages (>42.4 V
safety low-voltage (≤42.4 V
Caution
If your cable assemblywill be used in high-voltage applications (>42.4V
you must use UL style 2464 approved cable.
This document describes how to create and install a cable that connects
high current signals to the NI PXI-2585 or NI PXI-2586 switch module.
The connector and backshell kit for the PXI-2585/2586 switch module
contains all of the components necessary to build a cable assembly that is
safe for use with the entire operating range of the PXI-2585/2586 series of
products. Read through this installation guide carefully to ensure that the
cable you build is safe to use with your switch module.
/60 VDC) cannot be connected to any other solder cup pin.
pk
The PXI-2585/2586 connector and backshell kit contains the following:
•
Empty metal backshell
•
Solder cup pins (Qty. 22)
•
0.050 in. Allen wrench
•
Polyimide tape
You must supply the following items to complete the construction of the
cable:
•
Soldering iron
•
16 AWG stranded wire
•
Specifications for the module with which the cable will be used
/60 VDC) are present on any solder cup pin,
pk
/60VDC),
pk
Advertisement
Related Manuals for National Instruments NI PXI-2585
Summary of Contents for National Instruments NI PXI-2585
- Page 1 NI PXI-2585/2586 Connector and Backshell Kit This document describes how to create and install a cable that connects high current signals to the NI PXI-2585 or NI PXI-2586 switch module. Introduction The connector and backshell kit for the PXI-2585/2586 switch module...
- Page 2 The NI PXI-2585/2586 Specifications contains the pinout diagram necessary to Note build the cable. Visit for the most current specifications for your ni.com/manuals PXI-2585/2586 switch module. You must install this connector and backshell assembly according to local safety Caution codes and standards and according to the specifications provided by the connector manufacturer.
- Page 3 Remove the set screws from the knobs of the jack screws using the Allen wrench. Loosen the strain-relief bracket until it is fully open. Remove the metal backshell from the plastic connector. © National Instruments Corporation NI PXI-2585/2586 Connector and Backshell Kit...
- Page 4 Take care to insert the pin into the correct connector position. Once the pin is Note inserted, it can only be removed from the connector with an extraction tool. Extraction tools must be purchased separately. NI PXI-2585/2586 Connector and Backshell Kit ni.com...
- Page 5 The polyimide tape must be installed per these instructions or your cable will only Caution be rated to 42.4 V /60 VDC. 1 Polyimide Tape Figure 4. Connector Wrapped with Polyimide Tape © National Instruments Corporation NI PXI-2585/2586 Connector and Backshell Kit...
- Page 6 Replace the jack screw shaped like a socket nearest to pin “U” of the connector. Insert the male jack screw nearest to pin “A” of the connector to ensure proper mating. Accessories Table 1. Optional Third-Party Accessories for the NI PXI-2585/2586 Connector and Backshell Kit Accessory Manufacturer...
- Page 7 National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.