Product Description And Specifications; Product Features; Auxiliary Handle - Bosch Professional TSH 5000 Plus Manual

OBJ_BUCH-1466-004.book Page 3 Wednesday, December 16, 2015 1:47 PM
Hammer Safety Warnings
 Wear ear protectors. Exposure to noise can cause hear-
ing loss.
 Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
 Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an
electric shock.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for chiselling work in concrete, brick,
masonry and asphalt as well as for driving in and compacting,
when using the respective accessories.

Product Features

The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Dust protection cap
2 Locking sleeve
Bosch Power Tools
3 Lock-on button for On/Off switch
4 On/Off switch
5 Handle (insulated gripping surface)
6 Auxiliary handle (insulated gripping surface)
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Demolition Hammer
Article number
Rated power input
Impact rate
Impact energy per stroke
according to EPTA-Procedure
05/2009
Tool holder
Lubrication
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Assembly
 Before any work on the machine itself, pull the mains
plug.

Auxiliary Handle

 Operate your machine only with the auxiliary handle 6.
The auxiliary handle 6 can be set to any position for a secure
and low-fatigue working posture.
– Turn the bottom part of the auxiliary handle 6 in counter-
clockwise direction and swivel the auxiliary handle 6 to the
desired position. Then retighten the bottom part of the
auxiliary handle 6 by turning in clockwise direction.
Changing the Tool
The Hex tool holder allows for simple and convenient tool-free
changing of the application tool.
The dust protection cap 1 largely prevents the entry of drilling
dust into the tool holder during operation. When inserting the
tool, take care that the dust protection cap 1 is not damaged.
 A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
Inserting (see figure A)
– Clean and lightly grease the shank end of the tool.
– Push back the locking sleeve 2 and insert the tool in a twist-
ing manner into the tool holder. Release the locking sleeve
2 again in order to lock the tool.
– Check the latching by pulling the tool.
English | 3
TSH 5000 Plus
3 611 C38 180
W 1025
-1
min 2750
J 6.8
17 mm
Hex
Grease lubrication
kg 5.5
/II
1 609 92A 2G8 | (16.12.15)