Summary of Contents for Nilfisk Egholm City Ranger 2200
Page 1
’ peratOr s manual LAWN EDGER City Ranger 2200...
Page 2
Introduction Dear Customer Congratulations with your Nilfisk-Egholm product. The City Ranger 2200 is a Danish designed and manufactured product, which offers a very flexible way of maintaining outdoor areas. Optimal use of your Nilfisk-Egholm Lawn Edger To ensure optimal performance of your Nilfisk-Egholm Lawn Edger, please read this manual carefully before using the machine.
Do not drive on slopes with an incline of more than 10°. (Picture 4) Warning! Rotating parts! Máx. 10° Do not drive on slopes with an incline of more than 10° Operator’s Manual City Ranger 2200 Lawn Edger...
+45 97 81 12 05 Telephone: hereby declares that Machine: Lawn Edger 2200 22VKS1 Type: · has been manufactured in conformity with the provisions of the Machinery Directive 2006/42/EU Place: Lemvig Date: Signature: Knud Olsen, Senior Engineer Operator’s Manual City Ranger 2200 Lawn Edger...
520 mm Offset 150 mm Technical data: Type 22VKS1 Weight of Lawn Edger 50 kg Ground clearance below blade, lifted 140 mm Max. cutting depth 95 mm Attention: Specifications may change without notice. Operator’s Manual City Ranger 2200 Lawn Edger...
7. Push the lock button down to release the support strut; pull the strut up until the lock clicks into place. (Picture 3) Disassembly: Follow the procedure for fitting only in reverse order. Support strut Locked Operator’s Manual City Ranger 2200 Lawn Edger...
Make sure no one is standing too close to the machine while it is in use. N.B! When turning, the rear of the machine swings out, so there is a risk of crushing or collision. Operator’s Manual City Ranger 2200 Lawn Edger...
3. Stop the machine. Arrow Handle 4. Loosen the blade’s sideways grip. (Picture 3) 5. Adjust the blade’s position as desired. The blade must not be positioned beyond the arrow. (Picture 3) 6. Re-tighten the handle. Operator’s Manual City Ranger 2200 Lawn Edger...
Removing the bolt end piece and tighten again. 7. Refit the guard. Blade for cutting away from the machine. (Picture 3) Blade for cutting towards the machine. (Picture 4) Sharp edge Sharp edge Operator’s Manual City Ranger 2200 Lawn Edger...
6. Remove the nuts and bolts that hold the cultivator blades and remove the cultivator blades. (Picture 4) 7. Fit the new cultivator blades in the opposite order. Removing the bolt Sharp edge Operator’s Manual City Ranger 2200 Lawn Edger...
Page 12
4. Remove the bolt that holds the guard. (Picture 2) Detaching the guard 5. Remove the end piece, pipe and guard. (Picture 2) 6. Fit the new blades in the opposite order. Removing the bolt Operator’s Manual City Ranger 2200 Lawn Edger...
Page 13
When it is time to store the Lawn Edger for the winter, the following steps are recommended: 1. Remove any loose paint and repaint any damaged areas. 2. Spray the Lawn Edger with protective lubcricant. Screws that hold the wearing bar Operator’s Manual City Ranger 2200 Lawn Edger...
· Damage caused by force majeure such as lightning, flood, fire, war, civil disturbance, wrongfully perfomed maintenance or lack of the same, consequential damages or other causes over which Nilfisk-Egholm A/S has no control. Operator’s Manual City Ranger 2200 Lawn Edger...
1. Used hydraulic oil is to be disposed of at an approved waste disposal facility or site. 2. Remove and dispose of all plastic and rubber parts. 3. After the parts mentioned have been removed, the machine is ready to be handed over to an approved scrap merchant. Operator’s Manual City Ranger 2200 Lawn Edger...