Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Plymold Z000000469
Summary of Contents for Plymold Z000000469
- Page 1 Dining Counter Powered Z000000469 Revised 06/29/18 ...
- Page 2 Page 2 of 5 Dining Counter Unpacking Your Shipment Unpack and iden fy each component in each box that you received. STRETCHER HOLES SKIRT, LENGTH VARIES COUNTER TOP LENGTH VAR‐ LEFT AND RIGHT END LEGS (STETCHER HOLES 1 FACE) IES. HOLES FOR POWER ARE CENTER LEGS (STETCHER HOLES 2 FACE) APTIONAL WIRE CHASE LEG STRETCHER HARDWARE POWER (STARTER) CABLE CONNECTOR (JUMBPER ) CABLE MOIRE RECEPTACLE #10x1” Pan Head Angle Bracket 1” Plas c Anchor #10 x .5625” Pan Teardrop Glide MACHINE SCREW Sscrew 1” x 1” x2” Head Screw 1/4‐20 x 5/8” ...
- Page 3 Page 3 of 5 Dining Counter Assembly Step 1: Glide Assembly Glide a. Assemble thread‐in glide into the insert, in each set of legs Step 2: A ach Legs to Stretchers a. Using 1/4‐20 x 5/8” Machine Screws fasten legs to‐ gether. End legs are made to accept a stretcher on 1 face. Center legs are made to accept a stretcher on 2 faces. Step 3: A ach Top a. Center top from le to right on leg and stretcher as‐ sembly. Top should be flush with the back of legs. b. Then using #10 x 1 screws a ach the frame to the un‐ derside of the top, through the triangle plates on the legs. 4” BACK OF LEGS HAVE ANGLE BRACKETS Step 4: A ach Skirt a. Center skirt flush to the ends of the top. The skirt should sit 4” above the top. Using #10 x 0.625” screws a ach the skirt to the legs through the angle brackets on the legs. SKIRT ANGLE b. Add 1”x1”x2” angle brackets to finish a aching skirt. BRACKET ...
- Page 4 Page 4 of 5 Dining Counter Step 5: Add Power/ USB (OPTIONAL) a. Start with Link 1 on the end of the counter, nearest your power source. b. Slide the cords through the opening . Secure power in place using im‐ ages on the right as a guide. c. Repeat step b. with your remaining links . d. From below the top secure your wire chases to the underside of the top and the front face of the skirt using #10 x 0.5625” pan head screws. Hide all cords up inside the wire chase box. ...
- Page 5 Page 5 of 5 Dining Counter Step 6: Fasten Glides to Floor a. Rotate glides to point the moun ng hole towards the center of the counter. b. With a pencil, mark the hole loca on on the floor using the holes in the glide. c. Turn the glide away 90 degrees from its current posi on to expose the mark on the floor. d. Using a hammer drill and a 1/4” masonry bit, drill a 1 1/4” deep hole on the pencil mark. e. Place a plas c anchor in the hole and then rotate glide back so the hole lines up with the plas c an‐ chor in the floor. f. Insert a #10 x 1.0” screw through the hole in the glide and secure into the plas c anchor. Note: Frames must be anchored to the floor to maintain stability and prevent personal injury. Step 7: Clean a. Clean and protect top un l ready for use. ...
Need help?
Do you have a question about the Z000000469 and is the answer not in the manual?
Questions and answers