Dahua DSS4004-S2 Quick Start Manual
Hide thumbs
Also See for DSS4004-S2:
- Quick start manual (17 pages) ,
- Application deployment manual (18 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dahua DSS4004-S2
Summary of Contents for Dahua DSS4004-S2
- Page 1 DSS4004S2 Quick Start Guide V1.0.1...
- Page 2 Cybersecurity Recommendations Mandatory actions to be taken towards cybersecurity 1. Change Passwords and Use Strong Passwords: The number one reason systems get “hacked” is due to having weak or default passwords. It is recommended to change default passwords immediately and choose a strong password whenever possible.
- Page 3 8) Isolate NVR and IP Camera Network The network your NVR and IP camera resides on should not be the same network as your public computer network. This will prevent any visitors or unwanted guests from getting access to the same network the security system needs in order to function properly.
-
Page 4: Foreword
Foreword General The following document is used to guide users to know the checklist, installation and configuration etc. of DSS general surveillance management platform. Models DSS7016D-S2, DHI-DSS7016DR-S2, DSS7016D-S2 and DSS7016DR-S2. Safety Instructions The following categorized signal words with defined meaning might appear in the Manual. Signal Words Meaning Indicates a potential risk which, if not avoided, may result in... - Page 5 The Manual would be updated according to the latest laws and regulations of related regions. For detailed information, see the paper User's Manual, CD-ROM, QR code or our official website. If there is inconsistency between paper User's Manual and the electronic version, the electronic version shall prevail.
-
Page 6: Important Safeguards And Warnings
Important Safeguards and Warnings Operation Requirement Do not place or install the Device in a place exposed to sunlight or near the heat source. Keep the Device away from dampness, dust or soot. Keep the Device installed horizontally on the stable place to prevent it from falling. ... -
Page 7: Table Of Contents
Table of Contents Cybersecurity Recommendations ......................I Foreword ..............................III Important Safeguards and Warnings ..................... V 1 Checklist ..............................1 1.1 Package ............................1 1.2 Port Definition ..........................1 1.2.1 Front Panel ......................... 2 1.2.2 Rear Panel .......................... 2 1.3 Device Installation ......................... 3 2 Local Application ........................... -
Page 8: Checklist
Checklist Package Open product package to check, pay attention to product package, product unit and accessories. Check if the product is damaged or missing. Package: Product unit appearance is complete without obvious damage; after package is opened, check if accessories and HDD are complete. ... -
Page 9: Front Panel
1.2.1 Front Panel Figure 1-1 Table 1-2 Port or Tag Definition Network Indicator The blue light flashes when network is connected. Alarm Indicator The blue light flashes when device triggers alarm HDD1 System disk indicator, it flashes when reading disk. HDD2 Hard drive indicator, it is normally on when hard drive is HDD3... -
Page 10: Device Installation
Device Installation Connect cable according to port introduction, and then connect to power. Checklist 3... -
Page 11: Local Application
Local Application Function Architecture The chapter is to introduce the functions of the local application. See Figure 2-1. The local interface will be displayed after it starts up. See Figure 2-2. Figure 2-1 Time Setting Time Setting Basic Basic Standby Standby Network Mode Network Mode... -
Page 12: Business Config
Business Config 2.2.1 Basic Setting Click Basic Setting on the local interface, and configure time and other setting. Figure 2-3 Basic setting Table 2-1 Basic setting parameter description Parameter Description System Time Keep it the same as local time. Date Format It mainly focuses on data and time format of local application Date Separator homepage, and it is adjusted according to user experience. - Page 13 Figure 2-4 Network setting Table 2-2 Basic setting parameter description Parameter Note Local Application 6...
- Page 14 Parameter Note Supports following 4 modes. Multi-address It is the multi-network card mode; multiple network cards can configure different segments and realize multi-segment access, which is suitable for the scenario with high requirement of network reliability. For example, configuring dual hot standby needs to use network card 2 to configure standby heartbeat IP;...
-
Page 15: Operation Management
Operation Management 2.3.1 Operation Analysis Click Operation Analysis at the local interface and then you can check the status detection result of platform server, network, HDD and environment. Server Detection: Realizes real-time detection of the status of platform server, such as normal, stop and abnormal etc. -
Page 16: System Management
2.3.2 System Management Click System Management at the local interface. It supports following operations. Reboot: Please save system data before reboot. Shut down: Please save system data before shut it down. It is forbidden to power off directly. ... -
Page 17: Config System
Configuring System The server’s local application only provides basic configurations, such as time, language, network and quick management etc. It supports primary status operation and analysis in stand-alone environment. Please log in config system for deeper configurations of service, cluster, storage, linkage, map, database and security etc. Please refer to server user’s manual for more details.
Need help?
Do you have a question about the DSS4004-S2 and is the answer not in the manual?
Questions and answers