MEANS OF REPRESENTATION Symbols used The meaning of specific symbols is described below. Indicates an expected reaction (e.g. of a work step or a function). Indicates an unexpected reaction (e.g. of a work step or a function). Indicates a page reference (more information is provided on the specified page). Indicates information with more details or tips.
Page 5
SETUP Unpacking and setting up the vehicle Package 2 – Remove the box and the plastic packaging. Info To avoid damaging the motorcycle during the setup, leave the protective film on the vehicle until you have finished. – Remove the separate enclosure and unpack it. Check that the scope of supply is complete on the basis of the enclosed packing list.
Page 6
SETUP – Connect the plug-in connector for the FI warning lamp. Position FI warning lamp in the holder. – Wind the cable for the service hour counter (optional) around the ignition wire as described in the instructions enclosed, and secure using a cable tie. –...
Page 7
Position all controls in their exact positions on the handlebar. Tighten all screws. Guideline Screw, handle bar fixed 5 Nm Loctite ® 243™ grip, left (3.7 lbf ft) – Prepare the vehicle according to the specifications in the KTM Dealer.net for han- dover to the customer.
Page 8
WORK Raising the motorcycle with a lift stand Note Danger of damage The parked vehicle may roll away or fall over. – Always place the vehicle on a firm and even surface. – Raise the motorcycle at the frame underneath the engine. Lift stand (78129955100) Neither wheel is in contact with the ground.
WORK – Mount and tighten screw Guideline Screw, front wheel spindle M20x1.5 35 Nm (25.8 lbf ft) – Operate the hand brake lever several times until the brake linings are lying correctly against the brake disc. – Remove the motorcycle from the lift stand. ( p.
Page 10
WORK Removing the seat – Remove screws 102173-10 – Raise the rear of the seat, push the seat back, and lift it off. 102174-01 Mounting the seat – Hook in the front of the seat at the collar bushing of the fuel tank, lower it at the rear and simultaneously push it forward.
WORK – Press the spring with special tool Pliers for footrest spring (79029083000) The special tool is applied to area on the footrest. – Mount pin S00976-10 – Mount the washer and split pin S00975-10 Installing the battery Main work (All SX‑F models) –...
– Do not dispose of batteries with the household waste. Dispose of a defective battery in an environmentally friendly manner. Give the battery to your authorized KTM dealer or dispose of it at a collection point for used batteries. Warning Environmental hazard Hazardous substances cause environmental damage.
Page 13
WORK – Connect the battery charger to the battery. Switch on the battery charger. Battery charger (58429074000) You can also use the battery charger to test the open-circuit voltage and start potential of the battery, and to test the alternator. With this device, you cannot overcharge the battery.
Page 14
WORK (All SX‑F models) – Turn filler cap counterclockwise and lift it off. K00180-10 (XC‑F US) – Press release button , turn the filler cap counterclockwise, and lift it off. S00848-10 3.12 Closing the filler cap (All SX‑F models) –...
Page 15
WORK – Only refuel with clean fuel that meets the specified standards. Warning Environmental hazard Improper handling of fuel is a danger to the environment. – Do not allow fuel to get into the ground water, the ground, or the sewage system. –...
Page 17
SUBSTANCES Super unleaded (ROZ 95/RON 95/PON 91) Standard/classification – DIN EN 228 (ROZ 95/RON 95/PON 91) Guideline – Only use unleaded super fuel that matches or is equivalent to the specified fuel grade. – Fuel with an ethanol content of up to 10 % (E10 fuel) is safe to use. Info Do not use fuel containing methanol (e.