Related Manuals for Roswell Bennington C924-016650
Summary of Contents for Roswell Bennington C924-016650
- Page 1 Tower & Accessories Care / Maintenance / Operation Tower Part # C924-016650 or C924-017739 Bimini Part # C924-016652 Board Rack #C924-017091 Information: info@roswellmarine.com If you have any questions please call : 1-321-638-1331 Rev. 16-Aug-18...
- Page 2 Bennington Tower Care/ Maintenance/ Operations ww w.roswellmarine.com GENERAL TOWER CARE & MAINTENANCE This product is to be used for the sole purpose of wakeboarding, wakesur ng, hydrofoiling, and kneeboarding (rope handle sports). Do not attach devices like in atable tubes. The tower is intended to tow a maximum of two wake boarders at one time and no more than 400lbs (181kg) collectively.
- Page 3 Bennington Tower Care/ Maintenance/ Operations ww w.roswellmarine.com Folding Your Tower BEFORE ATTEMPTING TO FOLD YOUR TOWER : - Ensure two people are present. This is a two person operation. - Ensure all boards have been removed from racks. - Ensure swivels are locked into either the inside or outside positions. - Ensure your bimini is folded against the tower and secured.
- Page 4 Bennington Tower Care/ Maintenance/ Operations ww w.roswellmarine.com Folding Your Tower Fold the tower down With both latches released, slowly lower the tower until it rests at the stop position. This folded position is intended for low speed boat operation such as - Parking boat in garage - Boating under a bridge - Parking Boat in Slip...
- Page 5 Tower Bimini Care / Maintenance / Operation ***Important*** Read & follow these instructions carefully. Failure to do so may result in damage to parts. Damage to parts from improper use is not covered under warranty. GENERAL BIMINI CARE & MAINTENANCE Check all bimini hardware before every use on the water.
- Page 6 Bennington Tower Care/ Maintenance/ Operations ww w.roswellmarine.com Unfolding Your Tower Bimini Unfold the frame from the tower. Unzip the bimini boot Undo the 2 straps that secure the bimini to your tower. from the bimini frame. Unroll your fabric and middle bow.
- Page 7 Bennington Tower Care/ Maintenance/ Operations ww w.roswellmarine.com Folding Your Tower Bimini Detach the 6 bimini velcro straps around the frame and roll your bimini fabric towards the front bow. Velcro Straps Remove your 2 folding quick release pins and lower the Detach the wide strap around the tower front pipe.
- Page 8 Bennington Tower Care/ Maintenance/ Operations ww w.roswellmarine.com Trailering Your Tower Bimini Fold the bimini up towards the tower until it rests on top of the tower. Use the tie down straps and secure bimini to tower. Make sure Nav light is still visible. Tie Down Straps *** Illustrated is the ONLY acceptable way to safely fold your tower or trailer your tower with the bimini on***...
- Page 9 Bennington Tower Care/ Maintenance/ Operations ww w.roswellmarine.com Tightening Your Tower Bimini It is normal that your bimini canvas will stretch over time and use. Your tower bimini has been designed to allow you to tighten your canvas as needed. This method is best executed with 2 people Remove the rear bimini arm bolts on port and starboard sides.
- Page 10 4 : If your quick release pins are still di cult to remove and insert with the 3 : Now that your shim washers have been added your frame and arms addition of the arm shim washers, Roswell recommends using a drill with a should be parallel or much closer. Test removing and inserting your quick 5/16”...
- Page 11 w w w.roswellmarine. co m Board Rack Assembly Installation & Usage Part #C924-017091 Information: info@roswellmarine.com If you have any questions please call : 1-321-638-1331 Rev. 16-Aug-18...
- Page 12 Bennington Board Rack Assembly Instalation ww w.roswe llmarine.com Roswell strongly recommends that a routine inspection of hardware and components be done to ensure proper function and safety and to maximize product life. If bolts are found to be loose, discontinue use until threadlocker is re-applied and bolts are re-tightened.
-
Page 13: Package Contents
Fasten the medallion in place by inserting 2 set screws under the backing plate. Do not use thread lock on the set screws. 1: Mounting to a standard Tower -Proceed Below 2: Mounting to a Roswell Tower -Proceed to step K 3/32" Hand tighten... - Page 14 Bennington Board Rack Assembly Instalation ww w.roswe llmarine.com Before proceeding to step F, view the images below to know how your clamp and swivel adapter will look once assembled depending on which side it will be installed on. Port Configuration 1: Insert the angle adjustment piece into the clamp base in the orientation shown.
- Page 15 Torque bolts to 25ft-lb 1/4” Mounting to a standard Tower Mounting to a Roswell Tower Once installed proceed to step L Once installed Happy Boating. Add a drop of red threadlocker to each bolt first. Mount the rack and swivel assembly to the swivel adapter as illustrated with the 4 bolts provided.
- Page 16 Bennington Board Rack Assembly Instalation ww w.roswe llmarine.com Use with 2.5” clamp inserts Swivel your rack to the inside and outside positions with Apply a drop of red threadlocker to each Torque set screws a board. Ensure your swivel is operating well and set screw first.Once you are happy with to 25ft-lb locking in both positions.
- Page 18 Bennington Tower Installation Notes ww w.roswe llmarine.com NOTES...
Need help?
Do you have a question about the Bennington C924-016650 and is the answer not in the manual?
Questions and answers