WARNING! FOR OUTDOOR USE ONLY! DO NOT STORE OR USE COMBUSTIBLE MATERIALS IN OR NEAR THIS APPLIANCE. TO PREVENT INJURY, NEVER ATTEMPT TO MOVE GRILL WHILE HOT, OR WITHOUT ASSISTANCE. NEVER STORE ANY GRILL IN A SMALL SPACE OR PLACE IN A VEHICLE UNLESS COMPLETELY COOL AND FIRE IS VERIFIED AS EXTINGUISHED.
Warning: Read all Safety Information Before Operating Grill For outdoor use only. Do not use this grill for other than its intended purchase. REC TEC Grills strongly advises against using lighter fluid during the operation of your grill. Do not use alcohol, kerosene, or alcohol for lighting charcoal.
Page 6
Your carton contains the following: • 1 preassembled grill body (#1) • 1 WyldSide lift frame (#2) • 1 crank wheel (#3) • 1 side shelf with attached pull bar (#4) • 1 grilling grate frame (#5) • 2 pull bar handles (#6) •...
Page 7
Step 1: Unpack and Prepare for Assembly Unpack all contents, including the metal plate inside the cooking chamber of the grill. Use caution when unpacking lift frame and grill. Secure lift frame when removing plastic packaging material. Leave brackets zip tied to lift frame for easier installation until step 6.
Page 8
Step 2: Attach Wheels to Bottom of Grill For each wheel, you will need 4 bolts, 4 locking washers, and 4 flat washers found in the hardware pack (#18). Use this bolt assembly order for installation: bolt, lock washer, flat washer, wheel, grill. Hand tighten until all screws are in place.
Page 9
DO NOT ATTEMPT TO COMPLETE STEP 3 ALONE WITHOUT ASSISTANCE! Step 3: Stand Grill Upright Ensure all caster bolts are fully tightened and wheels are locked before standing grill up. With assistance, stand grill body upright and lock the caster wheels. LOCK CASTER WHEELS! UNLOCKED &...
Page 10
Step 5: Install WyldSide Lift Frame Slide WyldSide lift frame (#2) into the top of the preassembled grill body (#1). Cog wheel side of the lift frame should be on the RIGHT. Secure using 8 large bolts and washers found in the hardware pack (#18). Hand tighten until all screws are in place.
Page 11
Step 6: Install Grate Bracket Supports Use scissors to remove zip ties from brackets. Make sure all lift frame wires are free and untangled before installing bracket supports. Slide grate bracket supports into WyldSide lift frame (#2). Rotisserie cradle bracket (#11) Rotisserie drive motor mount receiving bracket (#13) on the LEFT (controller side) of...
Page 12
Step 7: Install Grilling Grate Frame Attach grilling grate frame (#5) to grate bracket supports (#11 & #13) by placing brackets on top of grilling grate frame. Secure grilling grate frame into place using 4 short bolts, 4 washers, and 4 nuts, from the hardware pack (#18).
Page 13
Step 8: Inspect Side Shelf Check side shelf with attached pull bar (#4) for fan obstruction by looking into fan hole. Step 9: Install Side Shelf Using 6 large bolts and 6 flat washers found in the hardware packet (#18), attach the side shelf (#4) to the left side of the grill body.
Page 14
Step 10: Install Pull Bar Handles Secure first pull bar handle (#6) to warmer box with 4 short bolts, 4 flat washers, 4 lock washers, and 4 nuts (#18). Use this bolt assembly order for installation: bolt, pull bar handle, warmer box door, flat washer, locking washer, nut.
Page 15
Step 11: Install Thermometer Attach thermometer (#17) to front left side of warmer box door by hand tightening gripped washer on the inside of the door to secure it into place. Step 12: Install Bull Emblem Attach bull emblem (# ) to front right side of warmer box door by placing mounting bracket on the inside of door.
Page 16
Step 13: Finish Warmer Box Make sure all packing material and tape is removed from the warmer box. Insert the warmer box grate (#22) into the warmer box. There are two positions for your warming grate. Be mindful of the thermometer when inserting the warmer box grate.
Page 17
Step 14: Install Crank Wheel Brake Attach crank wheel brake with one long black bolt above cog wheel. Make sure handle is in position between cog wheel and stopping pin. Step 15: Install Crank Wheel Attach the Crank Wheel (#3) to spit rod using locking pin to secure wheel to WyldSide Lift Frame (#2).
Page 18
Step 16: Place Grilling Grates Wash both grilling grates (#23) with mild soap and water before placing onto the grill. Ensure crank wheel brake (#20) is in the locked position. Insert grilling grates onto grate frame (#5). CORRECT RESTING POSITION Have Grilling Grate frame in the resting position before placing grates in the frame or you risk harming yourself or others.
Page 19
Step 17: Install Handles to Lid Using preinstalled hardware on handles, attach each handle to the stainless steel lid using this assembly order: Bolt, locking washer, flat washer, lid, handle. Hand tighten until all screws are in place. Step 18: Congratulations! Your grill is now built! You can now install your removable...
Page 20
Install Removable Hanging Double Hooks Step 1: Remove Pin and Place Remove pin and bolt to place removable hanging double hooks over the top of the WyldSide lift frame. Step 2: Adjust and Secure Replace bolt and pin to secure each hook to the frame.
Page 21
Install Rotisserie Step 1: Mounting the Bracket Slide the rotisserie drive motor mounting bracket (#13) into the rotisserie motor mount receiving bracket (#10) and secure with the pin found on the mounting bracket. Step 2: Install Rotisserie Drive Motor Slide rotisserie drive motor (#12) onto the rotisserie drive motor mounting bracket (#13).
Page 22
Step 4: Spit Rod Assembly Insert spit rod into motor and place other end on spit rod rest bracket making sure both spit rod bushings are used where the spit rod comes in contact with receiving and cradle brackets (this prevents a groove from being worn into the rod).
Page 23
• Free shipping • Six (6) Year Warranty • REC TEC Grills’ top notch customer service If you are not fully satisfied with your REC TEC grill, just return it within 30 days and we will refund your purchase price.
Page 24
Check your warmer box for any materials that may have been left inside before cooking on your grill. We also recommend placing your preferred fuel in the cooking chamber and allowing a fire to fully burn before your first cook. This will act as a burn in for your grill.
Page 25
When starting up your WyldSide, you’ll want to turn the dial up on your blower fan to get a fire started quickly and efficiently. For a lower, more controlled flame, turn the dial down. This variable speed blower fan will allow you to adjust airflow on the fly for whatever size flame your meal may call for.
Page 26
With the introduction of the WYLDSIDE, REC TEC GRILLS has entered the realm of cooking over a direct flame.
Page 27
• Foods cooked on pans or in containers will require more time than foods cooked directly on grates. • Use the REC TEC GRILLS Bullpen Instant Read Thermometer to determine meat-doneness, never rely on time. • Know your food’s internal temp! •...
Page 28
A few simple steps will ensure that your REC TEC WYLDSIDE will give you many years of service with minimal effort. • Clean your warmer grates with mild soap after each warmer use. • Clean your cooking chamber after every cook to ensure proper airflow.
Page 29
Ensure that the unit is cool. Remove the grates and make sure no unburnt fuel remains in the cooking chamber. STORE IN A DRY, SAFE PLACE Never store the grill in a small space or place in a vehicle unless completely cool and fire is verified as extinguished. Never move the grill while it is still hot.
Page 30
SMOKING 180ºF to 275ºF ROASTING / BRAISING 275ºF to 325ºF BAKING 325ºF to 375ºF GRILLING 375ºF to 450ºF BROILING / SEARING 450ºF + Use this chart* and a food thermometer to ensure that meat, poultry, seafood, and other cooked foods reach a safe minimum internal temperature.