Advertisement

COSEC DOOR V4
Quick Start
CONTENTS
Know Your COSEC DOOR
Please read this guide first for correct installation and retain it for future reference. The
information in this guide may change from time to time. However, Matrix Comsec
reserves the right to make changes in product design and specifications without prior
notice.
Copyright
All rights reserved. No part of this document may be copied or reproduced in any
form or by any means without the prior written consent of Matrix Comsec.
Warranty
Limited Warranty. Valid only if primary protection is provided, mains supply is within
limit and protected, and environment conditions maintained within product
specifications. Complete warranty statement is available on our website:
www.matrixaccesscontrol.com
3
3
4
5
5
5
6
12
14
14
15
15
16
17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the COSEC Door V4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Matrix COSEC Door V4

  • Page 1: Table Of Contents

    Please read this guide first for correct installation and retain it for future reference. The information in this guide may change from time to time. However, Matrix Comsec reserves the right to make changes in product design and specifications without prior notice.
  • Page 2: Front View

    Know Your DOOR Controller COSEC DOOR- Rear View COSEC DOOR- Front View CPM Slot LEDs LCD Display Card Personality Module* Numeric Keys ( CPM) Navigation Keys Ethernet Port Power In Finger Sensor TMPR/CTRL Door Lock Exit Reader Aux. Output RDR PWR RF Card Sensing Area Exit Switch Aux.
  • Page 3: Bottom View

    Preparing for Installation COSEC DOOR- Bottom View Step 1: Unpacking the DOOR Unpack COSEC DOOR and check your package contents. Ÿ Select a Location. It must be a flat surface such as a wall, close to the access Ÿ point (door). You can mount the COSEC DOOR directly to the wall or to an electrical box Ÿ...
  • Page 4 Ÿ Step 3: Mounting the Card Personality Module To access the door controller with card, you must order Matrix COSEC CPM (Card Personality Module separately. The module needs to be mounted on the COSEC DOOR prior to starting the wall mounting procedure as shown below.
  • Page 5 Refer the wire color code mapping for the terminals (figure 4). Ÿ If connecting Matrix PSBB-Universal Mains Power Supply (13.8 VDC@2A) with battery backup to the PWR In terminal, be sure to maintain correct polarity. The Variant COSEC DOOR FOP has all the connectors shown below whereas COSEC DOOR FOT has only Power, Ethernet and Exit switch connectors.
  • Page 6: Mounting The Door Controller

    To use the 12VDC of the Door, short the terminals COM (C5-1) and +ve (C5-4)as Ÿ shown in figure 5, before connecting the NC/NO and the -ve terminal (C5-5) to the Auxiliary Input Door lock. If you are connecting a sensor for detecting alarm conditions, connect the Ÿ...
  • Page 7: Powering On The Device

    Powering On the Device Apply Power to the COSEC Door Controller and wait for the reboot cycle to complete. At power on, all four LEDs will glow and will be turned off at the end of booting cycle. LED Status Indicators Allowed Denied Alarm...
  • Page 8: Connecting The Door To Cosec Server

    Connecting the Door to COSEC Server Connecting as a Panel Door The COSEC Door Controller can communicate with the COSEC Server in two ways: To use the COSEC Door Controller as a Panel Door, connect it directly to a Panel Lite over As a Direct Door Ÿ...
  • Page 9: Technical Specifications

    Technical Specifications COSEC DOOR V4- Product Variants COSEC DOOR V4- Product Variants Specification Specification FOPQ FOTQ FOTW FOPQ FOPW FOPW FOTQ FOTW General IN/OUT User Capacity 50,000 Exit Switch Port Event Buffer 5,00,000 Door Status Sense Credential Card, Pin & Finger...
  • Page 10 MATRIX COMSEC Head Office 394-GIDC, Makarpura, Vadodara - 390010, India Ph: (+91)1800-258-7747 Email: Support@MatrixComSec.com www.matrixaccesscontrol.com...

Table of Contents