Advertisement
model
no
...........................................................BG200/99.V3
.........................................................2
..................................................................600W
..................................................................230V,
..............................................................
........................................................2850rpm Weight ............................................................................
20kg
unpack the product and check contents should there be any damaged or missing parts
contact your supplier immediately.
Warning! Before
from
mains.
4.1.
eyeshield.
4.1.1.
remove retaining screws (fig 1. A) from the eyeshield bracket.
4.1.2.
Position the eyeshield bracket on the underside of the stone cover and align holes (fig
2) 4.1.3. fix eyeshield to cover with screws (fig 2.1). if the shield is loose and drops
down, tighten
4.1.4.
Loosen
screw
is
4.1.5.
Securely tighten
4.2.
tool rest.
note: some models may already have the tool rest assembled, but stone clearance must still
be checked.
4.2.1.
take tool rest (fig 5) and align it with bolt slot on the inside of the grinding stone cover
(X).
4.2.2.
Pass
4.2.3.
Position the rest at a maximum of 2mm from the stone surface and secure the
assembly by
4.2.4.
turn the grinding stones by hand to ensure clearance of above items.
4.3.
installation.
4.3.1.
securely bolt the grinder to a fireproof workbench using the base holes as a template. check
that
all assembly nuts and bolts are secure then read section 5 (grinding stones) before use.
5.1.
mandatOry Safety inStructiOnS. (the following instructions must be observed together
chapter 1 safety).
▲
danger! use of a damaged stone is dangerous and may cause damage or personal injury.
Warning! ensure grinder is unplugged from the mains power supply before attempting to
change grinding stones (or wheel).
5.1.1.
Only
are authorised to change and dress grinding stones (wheels).
5.1.2.
Grinding stones (wheels) used with machine must be of an adequate speed rating
and suitable for the
ensure the cutting stone's maximum speed specification is higher than that indicated
5.1.3.
on the machine
5.1.4.
check grinding stones are secure, and the stone is not worn or damaged, that there
are no fissures or
5.1.5.
ensure replacement stone is not damaged in any way such as cracks, deformations
or splinters etc.
5.1.6.
Also check the mounting flanges to ensure they are not deformed, burred or chipped. damaged
items
stone to break.
different size holder. 5.1.7.
stone before use by facing the
others and vulnerable items) and run for a short
5.2.
Stone changing procedure.
Warning! unplug grinder from the mains power supply before changing stone.
5.2.1.
raise the eye shield up, and away from the stone.
5.2.2.
loosen and pull the tool rest out as far as possible, but, dO nOt remove
5.2.3.
Remove the
cover
© Jack sealey limited
x
16mm
assembly check
to
shield
screws
(fig
3.1.)
and
2mm
from
the
arrestor screw
(fig
bolt
(A)
through
washers (B)
onto
tightening knob (c).
persons qualified under
and
holding
a
material to be ground.
data plate.
cracks. if damaged replace immediately.
must nOt be used as they may cause irregular pressure on the stone which may cause
dO nOt over tighten a stone. never tamper with a stone in order to adapt it to a
install a new stone as in 5.2. once mounted on the grinder test the
screws
from
the
(fig
6).
Original Language Version
supplied
stones
motor
50Hz
Axle
no
load
ensure
grinder
is
unplugged
(fig
3.2)
adjust
the
arrestor so
stone
face
(fig
4).
3.1).
both
slots
and
place
bolt.
"Abrasive Wheels
Regulations"
the
current
grinding wheel
grinder in a safe direction (point away from yourself,
time. dress the stone if necessary.
it
side
of
the
wheel
BG200/99.V3
with
Power
supply
diameter
speed
it
with
certificate
(fig
6).
cover
and
remove
|
Issue
1
the
19/12/16
Advertisement
