Advertisement
Advertisement
Table of Contents
Related Manuals for FAAC T-MODE TM R
Summary of Contents for FAAC T-MODE TM R
- Page 1 T-MODE TM R-W 868 Mhz...
-
Page 2: Declaration Of Conformity
DECLARATION OF CONFORMITY Manufacturer: FAAC S.p.A. Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY Declares that: Operator mod. TM 45 radio wind • conforms to the essential requirements of the following EEC directives: - 2006/95/EEC - 2004/108/EEC - 99/05/EEC • it thus conforms to the following harmonised standards: - EN 60335-1-95, EN60335-2- 97/10-2000. - EN 61000-3-2, EN61000-3-3, - EN55014-1, EN55014-2 Bologna, 01/12/2012 The Managing Director A. Marcellan WARNINGS FOR THE INSTALLER ATTENTION! To ensure the safety of people, it is important that 14. Keep radio controls or other pulse generators out of reach of... -
Page 3: Technical Specifications
T-MODE TUBULAR MOTORS WITH RADIO AND WIND 433MHz DESCRIPTION a Tubular motor b Example of wheel adapter. (Accessory) c Example of crown adapter. (Accessory) d Travel limit ring nut e Example of motor support (Accessory) Fig. 1 TECHNICAL SPECIFICATIONS T-MODE TORQUE FREQUENCY MAX. SPEED VOLTAGE FREQUENCY POWER CURRENT MOTOR MOTOR “L” LENGTH WITH PROTECTION 45 R (Nm) OF USE USE TIME (Rpm) (Hz) SHAFT MAX. DIAMETER ADAPTER (mm) CLASS... - Page 4 INSTALLATION 1) Measure dimension A on the tubular motor, as shown in figure 3 ref. a. 3.1 ASSEMBLING THE TUBULAR MOTOR 2) Drill a hole with a drill Ø 3 mm on the roller (Fig.3 ref. 1) Fit the crown adapter (Fig.2 ref.a ) in the tubular motor, b ) at the distance A, previously measured on the tubular until it is completely inserted in the guide on the travel motor (Fig.3 ref. a). limit ring nut. 3) Fit the assembled tubular motor inside the roller from the side opposite the cap, until the crown adapter is 2) Fit the wheel adapter (Fig.2 ref. b) in the motor shaft. 3) completely inside the roller (Fig.4 ref.a). Lock the adapter with the supplied stop. (Fig.2 ref. c ) 4) Make sure that the adapter is well secured (Fig.2 ref. 4X10 Fig. 4 4) Secure the wheel adapter to the roller with a tapping...
-
Page 5: Radio Version
3.3 ELECTRIC CONNECTIONS 3.3 ELECTRICAL CONNECTIONS 3.3.1 RADIO VERSION 3.3.2 WIND VERSION The series W tubular motor can be controlled both by the The series R tubular motor can be controlled both by the remote control and by a push-button with step-by-step remote control and by a push-button with step-by-step logic. In addition, a wind sensor (anemometer) can be logic. connected to the motor: it commands the closure of the rolling shutter as soon as the wind has reached a speed higher than 20 Km/h. - Page 6 b l a c k a n d t h e b r o w n w i r e s. ( Re l e a s e t h e push-button if the “step-by-step” push-button is available) ADJUSTMENT OF THE TRAVEL-LIMIT STOPS TYPE 3 TYPE 4 A system of electro-mechanical travel-limit stops is housed inside the FAAC tubular motors. These stops cut power to the motor, when the opening or closing limit of the roller- Fig.9 shutter is reached. According to the type of configuration of your instal- CORRELATION BETWEEN ROLLER ROTATION DIRECTION lation (Fig.9), follow the instructions in the following...
- Page 7 To help you find the travel-limit stop adjustment screws, refer to figures 11 - 12, according to the motor installation side (RH or LH), and to the box configuration (internal or external). ADJUSTMENT OF DESCENT TRAVEL-LIMIT STOP RELEVANT TRAVEL-LIMIT STOP RELEVANT TRAVEL-LIMIT STOP ROLLER ROTATION ROLLER ROTATION DIRECTION DIRECTION...
- Page 8 +33 4 72218700 tel. +1 904 4488952 tel. +971 42146733 www.faac.fr www.faacusa.com www.faac.ae FAAC FRANCE - AGENCE PARIS FAAC INTERNATIONAL INC Massy - Paris, France Fullerton, California - U.S.A. tel. +33 1 69191620 tel. +1 714 446 9800 www.faac.fr www.faacusa.com...
Need help?
Do you have a question about the T-MODE TM R and is the answer not in the manual?
Questions and answers