Crown CT33131 Original Instructions Manual page 14

23 Protective collar *
24 Cutting torch (assembled) *
25 Earth clamp (assembled) *
26 Pressure reducting valve (assembled) *
27 Hose clamp *
28 Hose *
29 Grounding wire *
30 Plug *
31 Connection pipe of pressure reducting valve *
32 Manometer *
33 Bracket *
34 Screw *
35 Mounting nut *
36 Protective cover *
37 Cutting torch body *
38 Nozzle *
39 Diffuser *
40 Electrode *
41 Allen key *
42 Button of torch
43 Cutting torch cable connector nut *
44 Cutting torch control cable connector nut *
45 Valve *
46 Condensate drain button *
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of machine
elements
Before carrying out any works on the machine it
must be disconnected from the mains.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Mounting / dismounting / setting-up of
some elements is the same for all ma-
chine models, in this case specific mod-
els are not indicated in the illustration.
Mounting / dismounting of a plug, current-carrying
cable, stationary network connection
Some machine models are supplied without plugs
and / or current-carrying cables - they must be installed
before the beginning of the operation�
Machines can also be connected to the network on a
stationary basis (not through a socket)�
Note: the stationary connection of the
machine to the network as well as instal-
lation or replacement of current-carrying
cables, plugs and other electrical units
must be performed only by a qualified electrician or
circuit installer authorized to perform such works.
Connection to the grounding loop (see fig. 1)
Using grounding bolt 2 connect one grounding wire
clamp 29 to the machine (see fig. 1). Connect the sec-
ond grounding wire clamp 29 to the working grounding
loop�
Compressor connection (see fig. 2-4)
• Extract plugs 30 (see fig. 2.1).
• Wind teflon tape (for tightening) around threaded
ends of connection pipes 31 and the threaded end of
manometer 32 (see fig. 2.2).
• Screw connection pipes 31 and manometer 32 in
the pressure reducting valve body 26 and tighten them
with a wrench (see fig. 2.3).
• Using screws 34, fix bracket 33 as shown in fig. 2.4.
• Unscrew the mounting nut 35, install pressure re-
ducting valve 26 and tighten mounting nut 35 (see
fig. 2.5).
• Cut hose piece 28 to the length necessary for con-
necting the outlet connecting pipe 31 ("OUT" marking)
of pressure reducting valve 26 with connecting pipe 4�
The second piece of hose 28 will be connected to the
compressor and inlet connecting pipe 31 ("IN" mark-
ing) of pressure reducting valve 26 (see fig. 3-4). Put
clamps 27 on where hose 28 ends�
• Connect the hoses 28 as shown in fig. 4. Fix hose 28
ending on the connecting pipes with clamps 27�
Cutting torch disassembly / assembly (see fig. 5-6)
[CT33131]
• Unscrew protective cover 36 (see fig. 5).
• Remove nozzle 38, diffuser 39 and electrode 40�
• If the details are well worn or damaged, replace
them�
• Assembly should be done in reverse sequence�
[CT33132]
• Unscrew protective cover 36 (see fig. 6).
• Unscrew nozzle 38 and electrode 40 from torch
body 37�
• If the details are well worn or damaged, replace
them�
• Assembly should be done in reverse sequence�
Connecting / disconnecting cables (see fig. 7)
• If necessary to connect connector to earth clamp ca-
ble 25 perform the operations, shown in fig. 7.1.
• Open protective cover of socket 5 and attach earth
clamp 25 to the machine as shown in fig. 7.2.
• Connect the cutting torch 24 to the machine (see
fig. 7.3):
• connect a cutting torch control cable� Set a control
cable connector in socket 6 and tighten a nut 44 by
hand� During installation, pay attention that locating
tab inside of a socket fits a location slot of the cable
connector;
• put the protective collar 23 on the screw nut 43;
• open protective cover of socket 7;
• put the screw nut 43 (by turning protective col-
lar 23) on the connector thread 7 (see fig. 7.3), and
tighten it manually�
• Disconnect of the cables in a reverse order�
Initial operating of the machine
Before starting the operation the following steps are
necessary:
• always use the correct supply voltage: the power
supply voltage must match the information quoted
on the machine body;
English
14