Related Manuals for H3C PSR3000-54AHD
Summary of Contents for H3C PSR3000-54AHD
- Page 1 H3C PSR3000-54AHD Power Module User Manual New H3C Technologies Co., Ltd. http://www.h3c.com Document version: 6PW101-20190308...
- Page 2 All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd. Trademarks Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.
-
Page 3: Table Of Contents
Contents Overview ·················································· 1 Front panel ···································································· 2 LEDs ············································································ 2 Technical specifications ··················································· 4 Power module configuration ·············································· 5 Power cords ··································································· 5 Installing and removing the power module ······· 8 Installing the power module ···············································... -
Page 4: Overview
Overview The PSR3000-54AHD power module supports both AC input and high-voltage DC input (240 VDC and 380 VDC). It is hot swappable and provides a maximum output of 3000 W. Table 1 PSR3000-54AHD power module features Feature Description Protection against input under-voltage, input... -
Page 5: Front Panel
Front panel Figure 1 Front panel (1) Power input LED (IN OK) (2) Handle (3) Power receptacle (4) Latch (5) Power output LED (OUT OK) (6) Air outlet vents LEDs The PSR3000-54AHD power module has two LEDs. - Page 6 Table 2 LED description Mark Color Description No AC power input. Power Low AC input voltage. The power input module has entered protected state. Green Normal AC input. Green Normal DC output. Orange High temperature. DC output failure. An alarm Power condition occurs, for example, output...
-
Page 7: Technical Specifications
Technical specifications Table 3 Technical specifications Item Specifications Rated input 100 to 240 VAC @ 50 or 60 Hz voltage AC input Maximum input 20 A current Rated input 240 to 380 VDC voltage DC input Maximum input 20 A current Rated output voltage 54 VDC... -
Page 8: Power Module Configuration
The rated current of the circuit breaker must be a minimum of 20 A. Power cords The PSR3000-54AHD power module must be used in conjunction with power cords listed in Table 4. Determine the power cord based on the power source conditions. - Page 9 Figure 2 CAB-HVDC Pwr-3m-336V power cord (1) Power module-side connector (2) Cable (3) Power source-side connector Figure 3 CAB-PDU Pwr-3m-PW3C450V power cord (1) Power module-side connector (2) Cable (3) Power source-side connector...
- Page 10 Figure 4 CAB-AC-Pwr-3m-PW3C450V power cord (1) Power module-side connector (2) Cable (3) Power source-side connector...
-
Page 11: Installing And Removing The Power Module
Installing and removing the power module Installing the power module To avoid bodily injury and device damage, follow the procedures Figure 5 to install a power module. Figure 5 Power module installation procedure Before the installation, prepare an ESD wrist strap and a flat-blade screwdriver yourself. - Page 12 Thread the flat-blade screwdriver through the hole in the handle of the filler panel and pull the filler panel out. Skip this step if the target slot does not have a filler panel installed. Figure 6 Removing a filler panel Unpack the power module.
-
Page 13: Connecting The Power Cord
The power module is foolproof. If the power module is oriented incorrectly, you cannot install the power module into the slot. If you encounter a hard resistance while inserting the power module, pull out the power module, reorient it, and then insert it again. - Page 14 To connect the power cord: Plug the power cord connector into the power receptacle of the power module. Make sure the clasp on the connector secures the connector into the power receptacle. Figure 8 Power module-side connector (1) Clasp Figure 9 Connecting the power cord to the power module...
-
Page 15: Removing The Power Module
Connect the other end of the power cord to the power source, and turn on the circuit breaker. Verify that the power input LED is ON. If the LED is on, the power cord is correctly connected. If the LED is OFF, troubleshoot the installation process. -
Page 16: Removing The Power Cord
Removing the power cord Turn off the circuit breaker of the power cord. Wear an ESD wrist strap, and make sure the strap makes good skin contact and is correctly grounded. Squeezing the connector between your thumb and forefinger, gently pull the power cord out, with your forefinger pressing the clasp upward. - Page 17 To remove the power module: Pressing the latch towards the handle direction, pull the power module out along the guide rails until it is part way out of the slot. As shown in Figure 12, grasping the handle of the power module with one hand and supporting the bottom of the power module with the other hand, pull the module slowly along the guide rails out of the slot.
Need help?
Do you have a question about the PSR3000-54AHD and is the answer not in the manual?
Questions and answers