Preparation - Siemens WT46B209EE Instructions For Installation And Use Manual

Only when switched off!
Care and cleaning
Installation
Dryer housing, control panel
– Scope of delivery: dryer, operating and installation instructions, basket for woollens
– Wipe clean with a soft, damp cloth.
(depending on the model).
– Do not clean with a water jet.
– Check the dryer for transport damage.
– Remove detergent and cleaning agent residue immediately. – The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– During drying, water may occasionally accumulate between the window and the seal.
– Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
This does not affect the proper operation of your dryer.
– Do not set up in a room that is susceptible to frost. Freezing water may cause damage.
Heat exchanger
– If in doubt, have the appliance connected by a specialist.
The heat exchanger requires cleaning once a month,
1. Setting up the dryer
however this varies depending on how frequently the dryer is used.
– The mains plug must always be accessible.
Allow the dryer to cool down and place an absorbent cloth under the maintenance flap.
– Ensure that the appliance is placed on a clean, level
Residual water may escape. and firm surface.
– Do not obstruct the air inlet on the dryer.
1. Unlock the maintenance flap and open completely.
– Keep the area around the dryer clean.
2. Turn both locking levers towards each another. – Level the dryer using the threaded feet
and a spirit level.
Never remove the threaded feet !
Do not install the dryer behind a door
or sliding door which could prevent or
3. Pull out the cap.
obstruct the dryer door from opening.
This will prevent children from locking
themselves in and risking their lives.
4. Remove the heat exchanger.
For mains connection,
2.
– Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
Take care not to damage the heat exchanger.
When cleaning, use water only. Do not use hard or sharp-edged objects. – The mains voltage and the voltage shown on the rating plate (
same.
– The connected load and necessary fuse protection are specified on the rating plate.
5. Rinse the heat exchanger and the cap on all sides with a jet of water to
Converting the installed load
completely remove all of the fluff. 3.
1. Turn the programme selector to
2. Press and hold the
6. Remove any fluff from the seals on the dryer and heat exchanger. 3. Turn the programme selector to algodón/algodão (cottons) extra seco (very dry) ;
wait until the recent setting appears in the display:
4. Press the (Fine adjust) button to change the settings.
7. Allow to drip dry fully.
5. Turn the programme selector to
8. First insert the heat exchanger, then the cap.
9. Turn back both locking levers and close the
maintenance flap until it locks closed.
Moisture sensors Frost protection/transport
The dryer is equipped with stainless steel moisture sensors.
Moisture sensors measure the moisture level of the laundry.

Preparation

After sustained, repeated operation, a fine layer of limescale
1. Empty the condensate container
may form on the moisture sensors.
2. Select any progra mme using the programme selector.
1. Open the door. 3. Press the inicio/pausa (start/pause) button
container.
2. Clean the moisture sensors with a damp sponge which has a rough
4. Wait several minutes or until the dryer stops, and then empty the condensate container
surface.
again.
5. Turn the programme selector to
Do not use steel wool or abrasive agents!
8
Optional accessories
order from the after-sales service using the order number, depending on the model) (
Washer-dryer stack connection set
WZ
The dryer can be placed on top of a suitable washing machine with the same width and depth to save space. The dryer must be fastened to the
11410
washing machine using this connection set. WZ 20400: with pull-out worktop.
WZ
Platform
20500 For easier loading and unloading. The basket contained in the drawer can be used to carry the laundry.
Technical data
Dimensions (DxWxH) 60 x 60 x 85 cm (height adjustable)
Take all accessory parts out Weight approx. 45 kg
of the drum. Max. capacity 9 kg
The drum must be empty.
Condensation container 4.2 l
Connection voltage 220-240 V
Connected load 2100-2800 W
Fuse protection 10 A / 16 A
Ambient temperature 5-35°C
Product number
Inside of door
Production number
The rating plate can be found on the back of the dryer.
Power consumption when switched off
Power consumption when ready for use (left-on mode)
Drum interior light (depending on model): The drum lights up after the door is opened and after the programme starts, and switches off
automatically.
Clean and level
Consumption values table
(The value on the label is achieved at the maximum heat setting.)
Make sure that the air inlet
remains unobstructed Spin speed which
Programme is used for spinning Duration**
see Safety instructions page 13.
the laundry
cottons 9 kg 4.5 kg
page 10) must be the
10 A 16 A 10 A 16 A 10 A
cupboard dry* 1400 rpm 152 min 122 min 82 min 65 min 4.36 kWh
1000 rpm 172 min 142 min 93 min 75 min 5.23 kWh
Note the fuse protection of the socket ( 10/16 Amps.).
800 rpm 192 min 162 min 104 min 85 min 6.02 kWh
(Off).
1400 rpm 127 min 105 min 68 min 53 min 2.61 kWh
iron dry*
(Fine adjust) button.
1000 rpm 149 min 126 min 79 min 63 min 4.01 kWh
=10A or =16A. 800 rpm 166 min 146 min 90 min 74 min 4.50 kWh
synthetics 3.5 kg
(Off). cupboard dry* 800 rpm 52 min 46 min 1.42 kWh
600 rpm 65 min 56 min 1.74 kWh
For testing in accordance with applicable standard EN61121 the dryer shall be used with external drain set.
* Programme setting for testing in accordance with the applicable EN61121 standard.
** The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual moisture in the fabric,
the degree of dryness that has been set and the amount of laundry being loaded.
Do not operate the dryer if
there is a risk of frost. Most efficient programme for cotton fabrics
The following "standard cottons programme" (identified with ) is suitable for drying normal, wet cotton laundry and is most efficient in terms of
its combined energy consumption for drying wet cotton laundry.
page 4/11.
Standard programme for cottons in accordance with current EU regulation 932/2012
condensation is pumped into the
Programme Load Energy consumption
10 A 16 A
cottons cupboard dry 9 kg/4.5 kg
(Off). 5.23kWh/2.78 kWh 5.23kWh/2.78 kWh 172 min/93 min
Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.
9
After-sales service
If you cannot rectify the fault yourself (e.g. switching off/on) What to do if..., page 11/12,
please contact our after-sales service. We will always find an appropriate solution and avoid
unnecessary visits by engineers.
The contact details of your local after-sales service can be found in the enclosed after-sales
service directory.
– GB 0344 892 8999 (Calls charged at local or mobile rate.)
– IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
Please provide the after-sales service the product number (E no.) and the production number
(FD) of the appliance.
You can find this information:
inside the door* / in the opened service flap*
and on the rear of the appliance.
*depending on the model
Product number Production number
Trust the expertise of the manufacturer. Contact us for assistance. In this way, you can rest
assured that the repair will be carried out by trained service technicians using original spare
parts.
0.10 W
1.00 W What to do if ...
Turn the programme selector to (Off) and remove the mains plug from the socket.
Energy consumption** The inicio/pausa (start/pause) Mains plug plugged in?
indicator light does not light up. Programme selected?
9 kg 4.5 kg Check the socket fuse.
16 A 10 A 16 A
The display panel light and Energy-saving mode is activated see the separate
4.36 kWh 2.32 kWh 2.32 kWh indicator lights (depending on Energy-saving mode instructions.
5.23 kWh 2.78 kWh 2.78 kWh model) go out and
6.02 kWh 3.20 kWh 3.20 kWh the inicio/pausa (start/pause)
indicator light flashes.
2.61 kWh 1.39 kWh 1.39 kWh
4.01 kWh 2.13 kwh 2.13 kwh The display panel switches off. The appliance goes into the sleep mode after activating
4.50 kWh 2.39 kwh 2.39 kwh (Finished in) option page 5.
3.5 kg
The (Condensate container) Empty the condensate container page 4.
1.42 kWh
indicator light flashes. Press the inicio/pausa (start/pause) button to reset the
1.74 kWh displayed indication and then press the inicio/pausa
(start/pause) button again to restart the appliance if
necessary.
If featured, check the hose for condensation outlet.
(Fluff filter/Heat exchanger) Clean the fluff filter page 4.
indicator light flashes. Press the inicio/pausa (start/pause) button to reset the
displayed indication and then press the inicio/pausa
(start/pause) button again to restart the appliance if
necessary.
Clean the heat exchanger page 8.
Dryer does not start. inicio/pausa (start/pause) button selected?
Programme duration
Door closed?
10 A 16 A Programme set?
142 min/75 min
11
10
What to do if ... Safety instructions
Programme terminates shortly Ambient temperature greater than 5°C? Emergency – Pull the appliance plug out of the socket immediately or disconnect the fuse.
after starting. Is the appliance loaded with the laundry?
ONLY use the – in rooms inside the house.
Load too small for selected programme?/Use timed dryer... – to dry fabrics.
programme page 6/7.
The dryer must – be used for purposes other than those described above.
Loaded laundry dry?
NEVER... – be modified in terms of its technology or properties.
Water is leaking out. Make sure the dryer is level. Hazards – The dryer must not be used by children or persons who have not been instructed in
its use.
Clean the heat exchanger seal.
– Do not leave children unsupervised near the dryer.
The door opens by itself. Push the door closed until you hear it engage.
– Keep pets away from the dryer.
– Remove all objects from pockets, and lighters in particular
Creasing. Laundry load exceeded? – Do not lean or sit on the door
Remove articles of clothing immediately after the end
Installation – Secure loose cables
of the programme, hang up and pull into shape.
– Do not operate a dryer if there is a risk of frost.
Unsuitable programme selected page 7.
Mains – Connect the dryer to an AC earthed socket according to specifications, otherwise it
connection cannot be guaranteed that the appliance is completely safe.
Laundry is not dried correctly or is After the end of the programme, warm laundry feels
still too damp. damper than it actually is. Spread the laundry out and – The cable cross-section must be sufficient.
allow the heat to disperse. – Only use earth-leakage circuit breakers with the following symbol:
– The appliance plug and socket must be compatible.
Finely adjust the dryness level – this extends the drying
– Do not use multiple plugs/connectors and/or extension cables.
time but does not increase the temperature. Your laundry
– Do not touch or hold the appliance plug with wet hands
will become drier.
– Never pull the appliance plug out of the socket by its cable.
– Do not damage the mains lead
Select a programme with a longer drying time or increase
the drying level. This does not increase the temperature. Operation – Only load the drum with laundry.
Check the contents before you switch the dryer on.
Select a time programme for extended drying of laundry – Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease
that is still damp. or paint (e.g. hair setting spray, nail polish remover, stain remover, cleaning solvent,
etc.) fire/explosion hazard.
If you have exceeded the maximum load for the
– The tumble dryer is not to be used if industrial chemicals have been used for
programme, the laundry may not be dried correctly. cleaning.
– Dust (e.g. coal dust, flour) poses a danger: do not use the dryer
Clean the moisture sensor in the drum. A fine layer of
hazard.
limescale may adversely affect the performance of the
– Do not turn off the dryer until the drying process ends, unless the laundry will be
sensors and your washing will not dry properly.
removed quickly and spread out, so that the heat can dissipate.
– Do not put laundry containing foamed material/rubber in the dryer
Drying has been interrupted as a result of a power cut,
material may be destroyed and the dryer may be damaged due to possible
because the condensate container is full or because the
deformation of the foamed material.
maximum drying time has been exceeded.
– When cleaning the fluff filter, make sure that no foreign material (down or filling
Drying time too long. Clean the fluff filter under running water page 4/11. material) gets into the air duct opening. If necessary, clean the drum beforehand with
a vacuum cleaner. If foreign material should still get into the air duct
Insufficient supply of air Ensure that air can circulate. sales service
– Light things, such as long hair, may be sucked into the air inlet of the dryer
Air inlet possibly blocked Clear inlet page 9.
Risk of injury.
– Final part of a tumble dryer cycle occurs without heat (cool down cycle), to ensure
Ambient temperature higher than 35°C Ventilate the
that the items are left at a temperature that ensures that the items will not be
room.
damaged.
– Switch off the dryer once the programme has ended.
One or more indicator lights are Clean the fluff filter and heat exchanger page 4,8/11.
– The exterior of the appliance's rear panel becomes very hot during
flashing. Check the installation conditions page 9.
operation. Never touch the hot surface of the appliance's rear panel. Keep
Switch off, allow to cool, switch back on and restart the
children away from the appliance
programme.
– The water from condensation is not drinking water and may be
contaminated with fluff.
Power failure. Remove the laundry from the dryer immediately and
spread out. This allows the heat to dissipate. Be careful Defect – Do not use the dryer if it is defective or if you suspect that it is.
as the door, the drum and the laundry may be hot. Repairs must only be carried out by the after-sales service.
– Do not use the dryer if the mains cable is defective. To avoid danger, only have the
defective mains cable replaced by the after-sales service.
Spare parts – For safety reasons, you must only use genuine spare parts and accessories.
Disposal – Pull out the appliance plug, then cut off the mains cable from the appliance.
Dispose of the appliance at a municipal waste disposal site.
– Packaging: Keep all packaging out of reach of babies and children
of suffocation.
– All materials are environmentally sound and can be reused.
Dispose of them in an environmentally-responsible manner.
12
Risk of explosion.
Risk of tipping.
Risk of tripping.
Risk of electric shock.
Risk of electric shock.
explosion
elastic
call the after-
Risk of fire/explosion.
Tumble dryer
WT46B209EE
Risk of burns!
siemens-home.com/welcome
en Instructions for installation and use
Observe the safety instructions on page 13.
Risk
Read these instructions and the separate
Energy-saving mode instructions before switching
13
on the dryer.
Register
your
product
online