Technical Features - Jacuzzi Experience Sienna Instructions For Preinstallation

It is the responsibility of the installer/owner to ascertain
compliance with specific local regulations prior to installa-
tion.
Jacuzzi Europe S.p.A. gives no guarantee in this respect
and refuses all responsibility regarding compliance of the
installation carried out.

Technical Features

i
Sienna Experience ( 1) includes:
- a control unit, called "Spa-Pak"
it is possible to additionally add a spa-pak "booster kit"
NOTE:
i
(optional,
2-2a, n°33
supplied as standard; refer to the relative documenta-
tion.
i
- the balance tank (
required to hold water that overflows when users get into the
tub. Its nominal capacity is 1,000 litres (operating with about
800-850 litres).
i
- the Hot tub ( 1, C), is to be connected, with hoses, to the
"Spa-Pak", the balance tank and the drain.
MAXIMUM ABSORPTION FOR THE SYSTEM
SINGLE-PHASE TOP
• version with heater
Power supply (x)
Volt Hertz Ampere
220-240 ~ 50/60
25,5 (k)
• version with exchanger
Power supply (x)
Volt Hertz Ampere
220-240 ~ 50/60
19,5 (k)
(k): at 230 V - (j): power absorption
(x): see the "electrical preparations" chapter
THREE-PHASE
Power supply Total consumption electric heater
(three-phase) (12 kW) +pumps+lights
Volt Hertz Ampere
(*) 50/60
220 - 240 3~ 45
50/60
26
380 - 415 3N~
(*): special standard (not valid for Europe)
WEIGHTS
MINIPOOL
Net weight average fill
kg
litres
~ 1430
~200
concentrated load on
resting surface
resting surface
m 2 kg/m 2
~2063
~0,95
i
.
( 1, A)
) to be connected to the one
) which, once connected, is
1, V/V1
Total consumption
hydro + filtering + heater (3 kW)
kW
5,75 (j)
Total consumption
hydro + filtering
kW
4,25 (j)
Total consumption only pumps and
lights (heat exchanger version)
kW Ampere
(j)
17 13
(j)
17
8
(j): max. power absorption
maximum
water volume max. weight
litres
~ 1760 ~1960
LOWERED
RETAINER TUB (V1)
RETAINER TUB (V)
SPA-PAK
Heat exchanger (optional)
- MAX primary circuit temperature .............................................................50 °C
- Connections.....................................................................................................................3/4"
- Primary circuit flow rate ..............................................................................38 l/min
- Primary pressure drop .....................................................................0,271 m H 2 O
Components
Components and the necessary connections for setting up the
system are described below (see
Hot tub and hosing
1 overflow channel with grid
2 buttons
2a box for connection of buttons
3 low-point drain with gate valve
to the balance tank (overflow lines)
4A1+4B1
4A2+4B2 to the balance tank (overflow lines)
4C1/4C2 from the overflow channel (overflow lines)
5 hydromassage pump suction lines
6 hydromassage pump delivery lines
7 filtering suction line
8 suction line from the balance tank
9 filtering return line
10 blower line (optional)
11 connections to the water system
12 perimeter metal supports
Spa-pak
13, 13a Electric wiring box
14 optional - 14b: heater or 14a: heat exchanger
15 hydromassage pumps
16 filtering pump
17 blower
18 quartz sand filter
19 safety switch
kW
20 temperature sensor
(j)
5
21 flow switch (models with heater)
(j)
5
Balance tank
22 water loading/filling solenoid valve (3/4")
23 level switches
24 check valve
25 gate valve (for emptying)
Total
26 pre-filters
kg
27 overflow
28, 29 ground drainage points
30 gate valves (for system maintenance)
31 gate valves (for suction balancing)
16
max weight
ground resting surface
at full load
kg m 2
~ 900 ~ 1,8
~ 925 ~ 1,2
~ 285 ~ 1,1
i
2-2a).
ground load
kg/m 2
~ 500
~ 770
~ 260