Table of Contents
Advertisement
Quick Links
Mini Deuterium Halogen Light Source
DT-Mini-2-GS
A
Installation and Operation Manual
Document Number 000-10000-110-02-0505
Offices:
Ocean Optics, Inc.
830 Douglas Ave., Dunedin, FL, USA 34698
Phone 727.733.2447
Fax
727.733.3962
8 a.m.– 8 p.m. (Mon-Thu), 8 a.m.– 6 p.m. (Fri) EST
Ocean Optics B.V. (Europe)
Geograaf 24, 6921 EW DUIVEN, The Netherlands
Phone 31-(0)26-3190500
F ax
31-(0)26-3190505
E-mail:
Info@OceanOptics.com
Info@OceanOpticsBV.com
Orders@OceanOptics.com
TechSupport@OceanOptics.com (Technical support)
WARNING
Product
(General sales inquiries)
(European sales inquiries)
(Questions about orders)
Protective Eye Wear Must Be Worn
When Using This Instrument -
Intense Ultraviolet Radiation Present
See Important Safety Notices inside.
Advertisement
Table of Contents
Related Manuals for Ocean Optics DT-Mini-2-GS
Summary of Contents for Ocean Optics DT-Mini-2-GS
- Page 1 Ocean Optics, Inc. 830 Douglas Ave., Dunedin, FL, USA 34698 Phone 727.733.2447 727.733.3962 8 a.m.– 8 p.m. (Mon-Thu), 8 a.m.– 6 p.m. (Fri) EST Ocean Optics B.V. (Europe) Geograaf 24, 6921 EW DUIVEN, The Netherlands Phone 31-(0)26-3190500 F ax 31-(0)26-3190505 E-mail: Info@OceanOptics.com...
- Page 2 Every effort has been made to make this manual as complete and as accurate as possible, but no warranty or fitness is implied. The information provided is on an “as is” basis. Ocean Optics, Inc. shall have neither liability nor responsibility to any person or entity with respect to any loss or...
- Page 3 Important Safety Notices 1. Do not remove or modify any installed safety device on this equipment. Doing so will void your warranty and create an unsafe operating environment. 2. Dangerous voltages are present in this device. There are NO user serviceable parts inside. 3.
- Page 4 Important Safety Notices 000-10000-110-02-0505...
-
Page 5: Table Of Contents
What’s New in this Document....................iii Document Summary ........................iii Product-Related Documentation....................iii Upgrades ......................... iii Chapter 1: Setup..................1 Overview.......................... 1 Unpacking the DT-Mini-2-GS..................... 2 Contents ............................ 2 Chapter 2: DT-Mini-2-GS Specifications..........3 Operating Environment....................3 DT-Mini-2-GS Components ..................... 3 Front Panel ..........................4 Rear Panel.......................... - Page 6 Table of Contents 000-10000-110-02-0505...
-
Page 7: About This Manual
Engineering-level documentation is located on our website at Technical → Engineering Docs. Upgrades Occasionally, you may find that you need Ocean Optics to make a change or an upgrade to your system. To facilitate these changes, you must first contact Customer Support and obtain a Return Merchandise... - Page 8 About This Manual Authorization (RMA) number. Please contact an Ocean Optics Application Scientist for specific instructions when returning a product. 000-10000-110-02-0505...
-
Page 9: Chapter 1: Setup
The following sections provide instructions on unpacking and setting up your Mini Deuterium Halogen Light Source (DT-Mini-2-GS). Before using the DT-Mini-2-GS for the first time, check for transport damage. Be sure to adhere to all warnings on the unit and in this manual. -
Page 10: Unpacking The Dt-Mini-2-Gs
2. Inspect the outside of the instrument and make sure that there is no damage. Do not use the instrument if damage is present. 3. Use this instrument in a clean laboratory environment. Contents Your DT-Mini-2-GS package should contain the following: DT-Mini-2-GS Mini Deuterium Halogen Light Source One IC-DB15-2 interface cable for shutter operation 000-10000-110-02-0505... -
Page 11: Chapter 2: Dt-Mini-2-Gs Specifications
Should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. DT-Mini-2-GS Components The following sections describe the components located on the front and rear of the DT-Mini-2-GS. 000-10000-110-02-0505... -
Page 12: Front Panel
To avoid this occurrence, connect the fiber optic cable to the SMA connector before starting the DT-Mini-2-GS lamp. Use caution when handling other end of the fiber optic cable to ensure that light radiation does not come into contact with skin and/or eyes. -
Page 13: Rear Panel
Rear Panel Rear View Power Input Connector When a 12VDC connection is supplied to the DT-Mini-2-GS, the lamp automatically switches to the basic operating mode. The LED indicator on the front panel will light to reflect this condition. Lamp ON/OFF/TTL Switch When this switch is turned ON (when the lamp has power), you can operate the lamp by using the switches on the front panel. - Page 14 2: DT-Mini-2-GS Specifications 000-10000-110-02-0505...
-
Page 15: Appendix A: Bulb Replacement
Use the following procedure to replace the bulb. ► Procedure 1. Remove the four screws on the bottom of the housing of the DT-Mini-2-GS and remove the cover. 2. Disconnect the four cables attached to the deuterium and halogen bulb. - Page 16 A: Bulb Replacement 3. Loosen the screw located on the bulb housing. Bulb Housing Screw 4. Remove the bulb from the DT-Mini-2-GS by gently pulling the bulb backwards out of the internal bulb socket. Pull Gently Caution Do not turn or wiggle the bulb during removal, as this can damage the bulb socket.
-
Page 17: Index
Index bulb replacement, 7 package contents, 2 Power Input Connector, 5 product-related documentation, iii components, 3 front panel, 4 rear panel, 5 setup, 1 SMA Connector, 4 specifications, 3 document audience, iii purpose, iii unpacking procedure, 2 summary, iii upgrades, iii Lamp ON/OFF/TTL Switch, 5 what's new, iii operating environment, 3... - Page 18 Index 000-10000-110-02-0505...
Need help?
Do you have a question about the DT-Mini-2-GS and is the answer not in the manual?
Questions and answers