Pump Alerts, Alarms and Trouble Shooting
Pump Alerts, Alarms and Trouble Shooting
Pump Alerts, Alarms and Trouble Shooting
When an Alert Activates:
When an Alert Activates:
When an Alert Activates:
Pump Alerts, Alarms and Trouble Shooting
Infusion continues, 3 beeps are heard. A message on the display
Infusion continues, 3 beeps are heard. A message on the display
Infusion continues, 3 beeps are heard. A message on the display
screen alternates with the infusion running screen until the end
screen alternates with the infusion running screen until the end
screen alternates with the infusion running screen until the end
When an Alert Activates:
of the battery or infusion.
of the battery or infusion.
of the battery or infusion.
Infusion continues, 3 beeps are heard. A message on the display
Low/end battery – the battery has approximately 30 minutes
Low/end battery – the battery has approximately 30 minutes
Low/end battery – the battery has approximately 30 minutes
screen alternates with the infusion running screen until the end
power remaining. Connect pump to charger or change battery pack.
power remaining. Connect pump to charger or change battery pack.
power remaining. Connect pump to charger or change battery pack.
of the battery or infusion.
Low/end battery – the battery has approximately 30 minutes
Program nearly complete – the programme/infusion has
Program nearly complete – the programme/infusion has
Program nearly complete – the programme/infusion has
power remaining. Connect pump to charger or change battery pack.
approximately 30 minutes until complete. Prepare to change
approximately 30 minutes until complete. Prepare to change
approximately 30 minutes until complete. Prepare to change
bag and re-programme or close down the device.
bag and re-programme or close down the device.
bag and re-programme or close down the device.
Program nearly complete – the programme/infusion has
approximately 30 minutes until complete. Prepare to change
When an Alarm Activates:
When an Alarm Activates:
When an Alarm Activates:
bag and re-programme or close down the device.
Infusion stops. LED indicator light turns red and the alarm sound
Infusion stops. LED indicator light turns red and the alarm sound
Infusion stops. LED indicator light turns red and the alarm sound
When an Alarm Activates:
continuously until either the pump is paused or the problem is
continuously until either the pump is paused or the problem is
continuously until either the pump is paused or the problem is
Infusion stops. LED indicator light turns red and the alarm sound
rectified. Always note the condition before pressing the STOP/NO
rectified. Always note the condition before pressing the STOP/NO
rectified. Always note the condition before pressing the STOP/NO
continuously until either the pump is paused or the problem is
button to silence the alarm.
button to silence the alarm.
button to silence the alarm.
rectified. Always note the condition before pressing the STOP/NO
Air/upstream occlusion – activates when either the upstream
Air/upstream occlusion – activates when either the upstream
Air/upstream occlusion – activates when either the upstream
button to silence the alarm.
segment of the tubing is trapped/clamped or when more than
segment of the tubing is trapped/clamped or when more than
segment of the tubing is trapped/clamped or when more than
Air/upstream occlusion – activates when either the upstream
the pre-set allowed volume of air has passed through the pump.
the pre-set allowed volume of air has passed through the pump.
the pre-set allowed volume of air has passed through the pump.
segment of the tubing is trapped/clamped or when more than
Silence the alarm, check the upstream tubing is not occluded.
Silence the alarm, check the upstream tubing is not occluded.
Silence the alarm, check the upstream tubing is not occluded.
the pre-set allowed volume of air has passed through the pump.
Down occlusion – indicates that an occlusion has blocked the line
Down occlusion – indicates that an occlusion has blocked the line
Down occlusion – indicates that an occlusion has blocked the line
Silence the alarm, check the upstream tubing is not occluded.
or access device causing pressure build up in the set. The clamp
or access device causing pressure build up in the set. The clamp
or access device causing pressure build up in the set. The clamp
Down occlusion – indicates that an occlusion has blocked the line
may be closed or set trapped/kinked, which you should resolve. If
may be closed or set trapped/kinked, which you should resolve. If
may be closed or set trapped/kinked, which you should resolve. If
or access device causing pressure build up in the set. The clamp
successful the pump automatically resumes infusion. If you cannot
successful the pump automatically resumes infusion. If you cannot
successful the pump automatically resumes infusion. If you cannot
may be closed or set trapped/kinked, which you should resolve. If
detect and resolve the cause the access device may be blocked.
detect and resolve the cause the access device may be blocked.
detect and resolve the cause the access device may be blocked.
successful the pump automatically resumes infusion. If you cannot
Silence the alarm and contact your Clinician immediately.
Silence the alarm and contact your Clinician immediately.
Silence the alarm and contact your Clinician immediately.
detect and resolve the cause the access device may be blocked.
Silence the alarm and contact your Clinician immediately.
Refer over the page for manual and pump priming instructions.
Refer over the page for manual and pump priming instructions.
Refer over the page for manual and pump priming instructions.
Refer over the page for manual and pump priming instructions.
Door open – pump door has been opened during infusing. Simply
Door open – pump door has been opened during infusing. Simply
Door open – pump door has been opened during infusing. Simply
close the door, silence the alarm and re-start.
close the door, silence the alarm and re-start.
close the door, silence the alarm and re-start.
Door open – pump door has been opened during infusing. Simply
close the door, silence the alarm and re-start.
Pump unattended – pump has been left 'stopped' or unattended
Pump unattended – pump has been left 'stopped' or unattended
Pump unattended – pump has been left 'stopped' or unattended
Pump unattended – pump has been left 'stopped' or unattended
(may have programmed but forgotten to press Start). Alarm
(may have programmed but forgotten to press Start). Alarm
(may have programmed but forgotten to press Start). Alarm
(may have programmed but forgotten to press Start). Alarm
sounds after 2 minutes to indicate that the pump is not infusing.
sounds after 2 minutes to indicate that the pump is not infusing.
sounds after 2 minutes to indicate that the pump is not infusing.
sounds after 2 minutes to indicate that the pump is not infusing.
Restart pump – a system malfunction has occurred. Press the
Restart pump – a system malfunction has occurred. Press the
Restart pump – a system malfunction has occurred. Press the
INFO key and record the error code. Some errors can be resolved by
INFO key and record the error code. Some errors can be resolved by
INFO key and record the error code. Some errors can be resolved by
turning the pump off and on again. If when the pump powers on
turning the pump off and on again. If when the pump powers on
turning the pump off and on again. If when the pump powers on
Restart pump – a system malfunction has occurred. Press the
the message is displayed again, discontinue using the equipment,
the message is displayed again, discontinue using the equipment,
the message is displayed again, discontinue using the equipment,
INFO key and record the error code. Some errors can be resolved by
contact your Clinician/Provider immediately and report the error
contact your Clinician/Provider immediately and report the error
contact your Clinician/Provider immediately and report the error
turning the pump off and on again. If when the pump powers on
code.
code.
code.
the message is displayed again, discontinue using the equipment,
End program – alerts the user that the programme/infusion is
End program – alerts the user that the programme/infusion is
End program – alerts the user that the programme/infusion is
contact your Clinician/Provider immediately and report the error
code.
now complete.
now complete.
now complete.
End program – alerts the user that the programme/infusion is
Missing key – the administration set is loaded incorrectly.
Missing key – the administration set is loaded incorrectly.
Missing key – the administration set is loaded incorrectly.
now complete.
Check that the key is positioned correctly inside the pump
Check that the key is positioned correctly inside the pump
Check that the key is positioned correctly inside the pump
before continuing.
before continuing.
before continuing.
Missing key – the administration set is loaded incorrectly.
Check that the key is positioned correctly inside the pump
Clinical contact:
Clinical contact:
Clinical contact:
before continuing.
Phone number:
Phone number:
Phone number:
Clinical contact:
E-mail contact:
E-mail contact:
E-mail contact:
Phone number:
The information contained in this guide is a summary only.
The information contained in this guide is a summary only.
The information contained in this guide is a summary only.
k
k
k
E-mail contact:
Refer to Operation Manual for full operating instructions.
Refer to Operation Manual for full operating instructions.
Refer to Operation Manual for full operating instructions.
The information contained in this guide is a summary only.
k
Screen information and sequences displayed are based on
Screen information and sequences displayed are based on
Screen information and sequences displayed are based on
k
k
k
Refer to Operation Manual for full operating instructions.
pump default settings and numerical values shown are
pump default settings and numerical values shown are
pump default settings and numerical values shown are
Screen information and sequences displayed are based on
examples only. You must refer to local policy/procedure for
examples only. You must refer to local policy/procedure for
k
examples only. You must refer to local policy/procedure for
pump default settings and numerical values shown are
specific guidance on pump settings/set-up, protocols and
specific guidance on pump settings/set-up, protocols and
specific guidance on pump settings/set-up, protocols and
examples only. You must refer to local policy/procedure for
use of accessories (e.g. cannula and administration lines).
use of accessories (e.g. cannula and administration lines).
use of accessories (e.g. cannula and administration lines).
specific guidance on pump settings/set-up, protocols and
When using the pump always follow screen prompts and
When using the pump always follow screen prompts and
When using the pump always follow screen prompts and
use of accessories (e.g. cannula and administration lines).
k
k
k
before pressing keys to proceed ensure selections made
before pressing keys to proceed ensure selections made
before pressing keys to proceed ensure selections made
When using the pump always follow screen prompts and
k
correspond with what is required.
correspond with what is required.
correspond with what is required.
before pressing keys to proceed ensure selections made
The information contained in this guide is applicable up
The information contained in this guide is applicable up
The information contained in this guide is applicable up
correspond with what is required.
k
k
k
to software versions TWINTPN02. NOTE: With previous
to software versions TWINTPN02. NOTE: With previous
to software versions TWINTPN02. NOTE: With previous
The information contained in this guide is applicable up
k
software versions some text wording/screen information
software versions some text wording/screen information
software versions some text wording/screen information
to software versions TWINTPN02. NOTE: With previous
may vary slightly.
may vary slightly.
may vary slightly.
software versions some text wording/screen information
may vary slightly.
CME
CME
CME
McKinley UK Ltd
McKinley UK Ltd
McKinley UK Ltd
Tel: 01253 894646
Tel: 01253 894646
Tel: 01253 894646
CME
McKinley UK Ltd
Tel: 01253 894646
Kincraig Business Park,
Kincraig Business Park,
Kincraig Business Park,
Fax: 01253 896648
Fax: 01253 896648
Fax: 01253 896648
Kincraig Business Park,
Fax: 01253 896648
Kincraig Road,
Kincraig Road,
Kincraig Road,
email: info@cme-mckinley.co.uk
email: info@cme-mckinley.co.uk
email: info@cme-mckinley.co.uk
Kincraig Business Park, Kincraig Road, Blackpool FY2 0PJ
Kincraig Road,
email: info@cme-mckinley.co.uk
Blackpool FY2 0PJ
Blackpool FY2 0PJ
Blackpool FY2 0PJ
Tel: 01253 894646 Fax: 01253 896648 info@cmemedical.co.uk
www.cme-mckinley.co.uk
www.cme-mckinley.co.uk
www.cme-mckinley.co.uk
Blackpool FY2 0PJ
www.cme-mckinley.co.uk
Twin Channel Infusion Pump
Twin Channel Infusion Pump
Twin Channel Infusion Pump
ConTinuouS Mode
ConTinuouS Mode
ConTinuouS Mode
Twin Channel Infusion Pump
Quick user guide
Quick user guide
Quick user guide
ConTinuouS Mode
Quick user guide
CME McKinley Device Training is RCN Accredited
CME McKinley Device Training is RCN Accredited
CME McKinley Device Training is RCN Accredited
CME Medical Device and Advanced User training is RCN accredited
The Multi-Function Keypad
The Multi-Function Keypad
The Multi-Function Keypad
and Skills for Health Quality Marked on all the guides.
CME McKinley Device Training is RCN Accredited
Keys '0' to '9' are used to enter numeric values during programming.
Keys '0' to '9' are used to enter numeric values during programming.
Keys '0' to '9' are used to enter numeric values during programming.
The Multi-Function Keypad
The Multi-Function Keypad
Keys'2' &'0' are also used to scroll up and down respectively in menus.
Keys'2' &'0' are also used to scroll up and down respectively in menus.
Keys'2' &'0' are also used to scroll up and down respectively in menus.
Keys '0' to '9' are used to enter numeric values during programming.
Keys '0' to '9' are used to enter numeric values during programming.
Keys '2' &'0' are also used to scroll up and down respectively in menus.
Keys '2' & '0' are also used to scroll up and down respectively in menus.
Powers the pump on and off. Press and hold until
Powers the pump on and off. Press and hold until
Powers the pump on and off. Press and hold until
confirmation beep sounds to power off.
confirmation beep sounds to power off.
confirmation beep sounds to power off.
Powers the pump on and off. Press and hold until
confirmation beep sounds to power off.
Starts/restarts the infusion.
Starts/restarts the infusion.
Starts/restarts the infusion.
Confirms programming or selection during set up.
Confirms programming or selection during set up.
Confirms programming or selection during set up.
Starts/restarts the infusion.
Confirms programming or selection during set up.
Stops the infusion when required.
Stops the infusion when required.
Stops the infusion when required.
Deletes numbers/settings.
Deletes numbers/settings.
Deletes numbers/settings.
Stops the infusion when required.
Takes user back up through the programming screens.
Takes user back up through the programming screens.
Deletes numbers/settings.
Takes user back up through the programming screens.
Takes user back up through the programming screens.
Allows set to be primed via the pump.
Allows set to be primed via the pump.
Allows set to be primed via the pump.
Allows set to be primed via the pump.
During an infusion repeatedly press to access
During an infusion repeatedly press to access
During an infusion repeatedly press to access
During an infusion repeatedly press to access
current infusion information: volume infused/to
current infusion information: volume infused/to
current infusion information: volume infused/to
current infusion information: volume infused/to
be infused, battery status and tube temperature).
be infused, battery status and tube temperature).
be infused, battery status and tube temperature).
be infused, battery status and tube temperature).
Allows the user to move between channels.
Allows the user to move between channels.
Allows the user to move between channels.
Allows the user to move between channels.
Need help?
Do you have a question about the BODY GUARD 2CH CONTINUOUS MODE and is the answer not in the manual?
Questions and answers