Advertisement
OPERATION
Lifting
1. Place vehicle in park, with emergency
brake on and the wheels diagonally op-
posite from the wheel being lifted shall
be chocked in both directions.
2. Locate and close release valve by turn-
ing it with the stamped end of the pro-
vided handle, clockwise, until it is firmly
tightened. Center the slotted saddle un-
der lift point. Jack shall be positioned
at 90 degrees perpendicular to the ve-
hicle frame seam, with the pump and
release valve facing the side of the ve-
hicle on which the tire being changed
is found.
3. Remove handle from release valve and
insert it into the handle socket. Pump
handle to raise saddle to vehicle manu-
facturers recommended lift point.
4. Pump further to desired height, but never
beyond a point just high enough to re-
move and install the tire.
Lowering
1. Remove handle from handle socket,
engage the release valve and slowly
turn the handle counterclockwise but
never more than 2 full turns.
2. After removing jack from under the load,
push saddle down to reduce ram ex-
posure to rust and contamination.
MAINTENANCE
Important: Use only a good grade hydrau-
lic jack oil. Avoid mixing different types of
fluid and Never use brake fluid, turbine
oil, motor oil or glycerin. Improper fluid can
cause failure of the jack and the potential
for sudden and immediate loss of load.
We recommend Mobil DTE 13M. Please
note that there are no replacement parts
applicable to this device.
MAINTENANCE (continued)
Adding oil
1. With saddle fully lowered set jack in its
upright, level position. Locate and re-
move oil filler plug.
2. Fill with oil until ~3/16" above the inner
cylinder as seen from the oil filler plug
hole. Reinstall the oil filler plug.
Changing oil
For best performance and longest life, re-
place the complete fluid supply at least
once per year.
1. With saddle fully lowered, remove the
oil filler plug.
2. Lay the jack on its side and drain the
fluid into a suitable container.
Note: Dispose of hydraulic fluid in accord-
ance local regulations.
Lubrication
A periodic coating of light lubricating oil to
pivot points, axles and hinges will help to
prevent rust and assure every parts
moves freely.
Note: Never apply lubricant directly on top
of saddle.
Cleaning
Periodically check the pump piston and
ram for signs of rush or corrosion. Clean
as needed and wipe with an oily cloth.
Note: Never use sandpaper or abrasive
material on these surfaces !
Storage
When not in use, store the jack with sad-
dle fully lowered.
4
90 DAYS LIMITED WARRANTY
For a period of ninety (90) days from date of purchase, Shinn Fu Co. of America,
Inc. will repair or replace, at its option, without charge, any of its products which fails due
to a defect in material or workmanship, or which fails to conform to any implied warranty
not excluded hereby.
Performance of any obligation under this warranty may be obtained by returning
the warranted product, freight prepaid, to Shinn Fu Co. of America, Inc. Warranty Service
Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by
applicable law, (1) the CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE
REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE,
and (2) Shinn Fu Co. of America, Inc. SHALL NOT BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE
DURATION OF ANY AND ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF NINETY (90) DAYS FROM
DATE OF PURCHASE.
Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
5
Advertisement
