1. Manuals
  2. Brands
  3. PEP Manuals
  4. Computer Hardware
  5. PB-SIO4
  6. Manual

PEP PB-SIO4 Manual

Quad serial port piggyback rs232
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PEP PB-SIO4 Manual

Advertisement

Table of Contents
loading

Related Manuals for PEP PB-SIO4

Summary of Contents for PEP PB-SIO4

  • Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
  • Page 2 PB-SIO4 Quad Serial Port Piggyback RS232 Manual ID 19957, Rev. Index 0300 Sep 99 The product described in this manual is in compliance with all applied CE stan- dards.
  • Page 3 This page was intentionally left blank. ® PEP Modular Computers GmbH...

  • Page 4: Table Of Contents

    Special Handling and Unpacking Instructions ..0 - 6 General Instructions on Usage......... 0 - 7 Two Years Warranty ............ 0 - 8 Table of Contents............0 - 9 19957 , Rev. 0300 ® PEP Modular Computers GmbH Page 0 - 3...

  • Page 5: Revision History

    This document contains information proprietary of PEP Modular Computers. It may not be copied or transmitted by any means, disclosed to others or stored in any retrieval system or media, without the prior written consent of PEP Modular Computers GmbH or one of its autho- rized agents.

  • Page 6: Explanation Of Symbols

    This symbol and title emphasize advantages or positive aspects of a product and/or procedure. Troubleshooting This symbol and title characterize a message containing useful information on troubleshooting and problem solving. 19957 , Rev. 0300 ® PEP Modular Computers GmbH Page 0 - 5...

  • Page 7: For Your Safety

    However, the life expectancy of your product can be drastically reduced by improper treat- ment during unpacking and installation. Therefore, in the interests of your own safety and of the correct operation of your new PEP product, you are requested to conform with the follow- ing guidelines.

  • Page 8: General Instructions On Usage

    Preface General Instructions on Usage In order to maintain PEP’s product warranty, this product must not be altered or modi- fied in any way. Changes or modifications to the device, which are not explicitly approved by PEP Modular Computers and described in this manual or received from PEP Technical Support as a special handling instruction, will void your warranty.

  • Page 9: Two Years Warranty

    However, no other warranties that may HARDWARE WARRANTY be granted or implied by anyone on behalf of PEP are valid unless the consumer has the express written consent of PEP Modular Computers. PEP Modular Computers warrants their own products, excluding software, to be free from manufacturing and material defects for a period of 24 consecutive months from the date of purchase.
  • Page 10 2.2 Software Installation ......... 2 - 4 Chapter 3. Configuration ............3 - 3 3.1 PB-SIO4 Address Map and ID Byte ....3 - 3 3.2 VMEbus Interrupts..........3 - 3 3.3 Jumper Settings..........3 - 4 3.4 Pinouts.............. 3 - 5 19957 , Rev.
  • Page 11 Preface PB-SIO4 Chapter 4. Adapter AD-SIO4............4 - 3 4.1 Product Overview ..........4 - 3 4.2 Adapter Overview ..........4 - 3 19957 Page 0 - 10 ® PEP Modular Computers GmbH , Rev. 0300...
  • Page 12 1.1.2 Features ................1 - 3 1.2 Board Overview ..............1 - 3 1.3 Functional Block Diagram .............1 - 4 1.4 PB-SIO4 External Interfaceing..........1 - 5 1.5 Carrier Board External Connectors........1 - 5 1.6 Technical Specifications ............1 - 6 1.7 Applied Standards..............1 - 7 1.7.1 CE Compliance..............1 - 7...
  • Page 13 This page was intentionally left blank. ® PEP Modular Computers GmbH...

  • Page 14: Introduction

    There are two different versions of the PB-SIO4 available: non-optoisolated and optoiso- lated. Any version combination can be installed on a single carrier board. Interfacing to the PB-SIO4 depends on the type of connector provided by the carrier board or optional adapters.

  • Page 15: Functional Block Diagram

    PB-SIO4 Introduction Figure 1-1: PB-SIO4 Board Front View (Optoisolated Version) Transceiver DUART DUART OPTO- ISOLATION Transceiver Logic 1.3 Functional Block Diagram Figure 1-2: Functional Block Diagram of the PB-SIO4 DUART I/F LOGIC DUART * Optoisolation is optional Page 1 - 4 ®...

  • Page 16: Pb-Sio4 External Interfacing

    Introduction 1.4 PB-SIO4 External Interfacing Connection of the PB-SIO4 piggyback to external devices is a function of the specific carrier board for the piggyback. In conjunction with the carrier board there are various possibilities for connecting the I/O channels of the piggyback to external devices.

  • Page 17: Technical Specifications

    PB-SIO4 Introduction 1.6 Technical Specifications Table 1-1: PB-SIO4 Technical Specification PB-SIO4 Specification Standard RS232 Number of Channels four per PB-SIO4 module Controller two MC68681 DUART’s (one pro port pair) Transfer Rates asynchronous: up to 38 kBaud or 115 kBaud depending on...

  • Page 18: Applied Standards

    PB-SIO4 Introduction 1.7 Applied Standards 1.7.1 CE Compliance The PEP Modular Computers’ VME products comply with the requirements of the fol- lowing CE-relevant standards: • Emission EN50081-1 • Immission EN50082-2 • Electrical Safety EN60950 1.7.2 Mechanical Compliance • Mechanical Dimensions IEEE 1101.10...
  • Page 19 This page was intentionally left blank. ® PEP Modular Computers GmbH...
  • Page 20 PB-SIO4 Installation Chapter Installation 2.1 Board Installation ..............2 - 3 2.2 Software Installation..............2 - 4 2.2.1 Driver Installation ............2 - 4 ID 19957, Rev. 0300 ® PEP Modular Computers GmbH Page 2 - 1...
  • Page 21 This page was intentionally left blank. ® PEP Modular Computers GmbH...

  • Page 22: Installation

    • if required, remove the carrier board and optional adapters from the system • ensure the proper orientation of the PB-SIO4 to the carrier board before installing (see appropriate documentation for orientation) • press the piggyback onto the carrier board until fully seated...

  • Page 23: Software Installation

    Drivers are available for various operating systems but are not delivered with the PB- SIO4. If required, please order the appropriate driver separately. For installation of any required driver, please refer to the driver documentation itself. Page 2 - 4 ® PEP Modular Computers GmbH ID 19957, Rev. 0300...
  • Page 24 PB-SIO4 Configuration Chapter Configuration 3.1 PB-SIO4 Address Map and ID Byte ........3 - 3 3.2 VMEbus Interrupts..............3 - 3 3.3 Jumper Settings..............3 - 4 3.4 Pinouts.................. 3 - 5 3.4.1 PB-SIO4/Carrier Board Connector ST1 ....... 3 - 5 3.4.2...
  • Page 25 This page was intentionally left blank. ® PEP Modular Computers GmbH...

  • Page 26: Configuration

    3. Configuration 3.1 PB-SIO4 Address Map and ID Byte The PB-SIO4 is addressed (odd byte access) by using the carrier board base address and one of the following offsets for the piggyback location: Piggyback location A ( the upper position on the carrier board)

  • Page 27: Jumper Settings

    PB-SIO4 Configuration 3.3 Jumper Settings The jumper positions B1 to B6 are located on the front side of the PB-SIO4. They are set at the factory as required and should not be changed. Note! Jumpers B1 through B6 are zero-Ohm resisters.

  • Page 28: Pinouts

    3.4 Pinouts 3.4.1 PB-SIO4/Carrier Board Connector ST1 This is a thirty pin, dual row male header connector which provides interfacing between the PB-SIO4 and CPU side of the carrier board. Table 3-2: Pinout of Connector ST1 Signal Signal +5V (Vcc)

  • Page 29: Pb-Sio4/Carrier Board Connector St2

    Configuration 3.4.2 PB-SIO4/Carrier Board Connector ST2 This is a twenty-six pin, dual row male header connector which provides interfacing between the PB-SIO4 and the application side of the carrier board. Table 3-3: Pinout of Connector ST2 Signal Signal RxD D...

  • Page 30: Pb-Sio4 To Carrier Board To Ad-Sio4

    PB-SIO4 Configuration 3.4.3 PB-SIO4 to Carrier Board to AD-SIO4 Table 3-4: PB-SIO4 to Carrier Board to AD-SIO4 Pinout Table (Both Positions) POS./ AD-SIO4 Carrier DUART Front Panel Signal SIO4 Board PINS CON/CH RTSD 1, 2 RxD D 25,26 VccE2 TxD D...
  • Page 31 PB-SIO4 Configuration Table 3-4: PB-SIO4 to Carrier Board to AD-SIO4 Pinout Table (Both Positions) POS./ AD-SIO4 DUART Carrier Front Panel Signal SIO4 Board PINS CON/CH RTSD 1, 2 RxD D 25,26 VccE2 TxD D CTSD GndE2 RTSC RxD C VccE2...
  • Page 32 PB-SIO4 Adapter AD-SIO4 Chapter Adapter AD-SIO4 4.1 Product Overview ..............4 - 3 4.2 Adapter Overview ..............4 - 3 ID 19957, Rev. 0300 ® PEP Modular Computers GmbH Page 4 - 1...
  • Page 33 This page was intentionally left blank. ® PEP Modular Computers GmbH...
  • Page 34 24-pin, dual row female connectors for connection to the adapter. This cable allows for the connection of two PB-SIO4’s to two AD-SIO4’s where pins 25 and 26 are not used. See Table 3-4 for the pinout of this cable.
  • Page 35 RESERVED DO NOT USE (see note below) Connector BU5 is for use with the PB-SIO4. Connector BU6 is reserved for use with the PB-SIO4A, another serial interface piggyback from PEP. Note! Always ensure that the correct connector of the adapter cable is connected to BU5.
  • Page 36 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...

This manual is also suitable for:

Pb-sio4a

Table of Contents