Download Print this page
DSC PowerSeries Neo V1.2 Installation Manual

DSC PowerSeries Neo V1.2 Installation Manual

Alarm control

Advertisement

Quick Links

To download the full installation and user manuals and register your product, please visit:
www.DSC.com/m/29009529 or scan the QR code to the right.
Quick Setup
Plan the installation including all alarm detection devices,
1
Plan
zone expanders, keypads and other required modules.
2
Mount
Decide on a location for the alarm panel and secure it to the
wall using suitable mounting hardware.
3
Wire
Complete all wiring including modules, zones, bells/sirens,
telephone line connections and ground connections. Record
module serial numbers on page 19.
4
Power
Connect the battery and power up the system. The battery
must be connected.
5
Enroll
Hardwired: Wire the keypad to the Corbus, power up the
First
alarm panel then press any button on the keypad. Wireless:
Keypad
Wire the HSM2Host to the Corbus, then power up the alarm
panel and a wireless keypad. Press any button on the keypad to
enroll it. The HSM2Host is then enrolled on the alarm panel.
Alternately, enroll an RF keypad.
6
Enroll
[*][8][Installer Code][902] subsection [000]. Press [*] to
begin auto-enrollment. Module slots are automatically
modules
assigned. Use scroll keys to view slots. Change slot by typing a
2-digit number.
Enroll
[*][8][Installer Code][804] subsection [000]. Note: An
7
wireless
HSM2HOST or RF keypad must be enrolled first.
devices
Program
Basic programming: [*][8][installer code] [001]/[002]> Zone
8
Type/Zone Attribute [005]>[001] Partition 1 Timers: – Entry
Delay 1 – Entry Delay 2 – Exit Delay [301]>[001] Phone #1
[310]>[000] System Account Code.
9
Test
Test the panel completely to ensure that all features and
functions operate as programmed. – [901] Walk Test – [904]
[000] Wireless Placement Test.
Compatible Devices
Throughout this document, x in the model number represents the
operating frequency of the device as follows: 9 (912-919 MHz), 8
(868MHz), 4 (433MHz).
Note: Only models operating in the band 912-919 MHz are UL/ULC
UL
listed where indicated. Only
UL/ULC listed systems.
Table 1-1 Compatible Devices
Modules
Wireless keypads:
Hardwired keypads with 2-way wireless
integration module:
Hardwired keypads:
Touchscreen Keypad
WARNING: This manual contains information on limitations regarding product use and function and information on
the limitations as to liability of the manufacturer. The entire manual should be carefully read.
PowerSeries Neo V1.2 Alarm Control Installation Guide
approved devices are to be used with
UL
HS2LCDWFx
HS2LCDWFPVx
HS2LCDWFPx
UL
HS2LCDRFx
UL
HS2ICNRFx
UL
HS2LCDRFPx
UL
HS2ICNRFPx
UL
UL
HS2LCD
HS2ICNP
HS2LCDP
UL
HS2LED
UL
HS2ICN
UL
HS2TCHP
Note: For ULC-s559 Listed applications the
HS2TCHP touch screen keypad is for
supplementary use only.
2-way wireless integration module:
8-zone expander:
8-output expander:
Power supply:
4 high current output expander:
Alternate communicator:
Hardwired Devices
2-wire smoke detectors:
y= A, B, or C
A: ULC listed models
B: UL listed models
C: European and Australian models
4-wire smoke detectors:
y= A, B, or C
A: ULC listed models
B: UL listed models
C: European and Australian models
CO detectors:
Wireless Devices
Wireless PG smoke detectors
Wireless PG smoke and heat detector
Wireless PG CO detector:
Wireless PG PIR motion detectors:
Wireless PG PIR + camera motion detector
Wireless PG curtain motion detector
Wireless PG dual tech motion detector
Wireless PG mirror motion detector
Wireless PG outdoor motion detector
Wireless PG glass break detector:
Wireless PG shock detector:
Wireless PG flood detector:
Wireless PG temperature detector (indoor use):
Outdoor temperature probe (requires PGx905)
Wireless PG keys:
Wireless PG panic key
Wireless PG 2-button key
Wireless PG sirens:
UL
Wireless PG repeater:
Wireless PG door/window contacts:
UL
Wireless PG door/window contact w/ AUX
Central Station Receivers
SG-System I, II, III, IV, 5
Enclosures
PC5003C, PC4050CR (ULC Fire Monitoring), PC4050CAR (UL Commercial Burg), CMC-1(UL
Commercial Burg), PC4051C. Other enclosures are available to suit a variety of system configurations.
HSM2HOSTx
UL
HSM2108
UL
UL
HSM2208
HSM2300
UL
HSM2204
UL
UL
UL
3G2080
TL2803G
UL
UL
3G2080R
TL2803GR
TL280
UL
PCL-422
UL
UL
TL280R
UL
FSA-210x
FSA-210xR
UL
UL
FSA-210xT
UL
FSA-210xRT
FSA-210xS
UL
FSA-210xRS
UL
UL
FSA-210xST
FSA-210xRST
UL
FSA-210xLST
FSA-210xLRST
FSA-410x
UL
FSA-410xR
UL
UL
UL
FSA-410xT
FSA-410xRT
UL
UL
FSA-410xS
FSA-410xRS
FSA-410xST
UL
FSA-410xRST
UL
FSA-410xLST
FSA-410xLRST
CO-12/24
UL
FW-CO1224
UL
UL
UL
12-24SIR
CO1224
UL
FW-CO12
UL
PGx926
UL
PGx916
UL
PGx913
UL
PGx904(P)
UL
PGx934(P)
UL
PGx924
PGx984(P)
UL
PGx974(P)
UL
PGx994
PGx912, PGx922
UL
PGx935
UL
PGx985
UL
PGx905
PGTEMP-PROBE
UL
PGx939
UL
PGx929
UL
PGx938
UL
PGx949
UL
PGx901
UL
PGx911
UL
PGx920
UL
PGx975
UL
PGx945
UL
UL
UL
UL

Advertisement

loading
Need help?

Need help?

Do you have a question about the PowerSeries Neo V1.2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for DSC PowerSeries Neo V1.2

  • Page 1 To download the full installation and user manuals and register your product, please visit: www.DSC.com/m/29009529 or scan the QR code to the right. PowerSeries Neo V1.2 Alarm Control Installation Guide Quick Setup Note: For ULC-s559 Listed applications the HS2TCHP touch screen keypad is for supplementary use only.
  • Page 2 PowerSeries Neo Installation Guide (c) Disposal of used batteries must be made in accordance with local waste recovery and Safety Instructions for Service Personnel recycling regulations. Warning: When using equipment connected to the telephone network, always follow the (d) Before servicing, DISCONNECT the power and telephone connection. basic safety instructions provided with this product.
  • Page 3 PowerSeries Neo Installation Guide can be T-tapped. Corbus (700mA max.)*** Do not use shielded wire for Corbus wiring. Note: Any module can be connected anywhere along the Corbus. Separate wire runs for keypads, zone expanders etc. are not necessary. Note: No module can be more than 1,000'/305m (in wire length) from the PCLink+ (Alt.
  • Page 4 PGM outputs). Connect the positive side of any device to the AUX+ terminal, the negative side to GND. The AUX output is protected; if too Secondary: 16.5VAC/40VA DSC PTD1640U, DSC PTC1640U Class 2 much current is drawn from these terminals (wiring short) the output is transformer.
  • Page 5 PowerSeries Neo Installation Guide To enable SEOL supervision, program section [013], options [1] and [2] The Bell output is supervised and power limited by 2A thermistor. If to OFF. unused, connect a 1000Ω resistor across Bell+ and Bell- to prevent the panel from displaying a trouble.
  • Page 6 PowerSeries Neo Installation Guide Programming Methods Enrolling Modules During automatic and manual enrollment, if an attempt is made to enroll The alarm system can be programmed using the following methods: more than the maximum number of modules, an error tone sounds and a Table 1-6 Programming Methods message is displayed on LCD keypads.
  • Page 7 PowerSeries Neo Installation Guide Use this section to set the language displayed by LCD keypads. To select a 3. Press the [#] and reapeat step 2 for next keypad. When finished language: programming all keypads, press the [#] key twice to exit programming.
  • Page 8 PowerSeries Neo Installation Guide 5 – Force Arm as [03] and [04] for Ethernet, and two of the receivers as [05] and [06] for cellular. 6 – Swinger Shutdown Testing the System 7 – Transmission Delay Installer Walk Test 8 – Burglary Verification Walk test enables the installer to test the operation of each detector by 9 –...
  • Page 9 PowerSeries Neo Installation Guide To view trouble conditions: Trouble 05 – Device Faults: [01] Zone 001 - 128: A zone is in fault. Additional information displayed on LCD Press [*][2] to enter the Trouble menu. keypads for the following troubles: Fire Trouble (2-W Smoke, PGX916, PGX926), On an LCD keypad, scroll to a trouble type then press [*] to view Freeze (PGX905), Self Test (PGX984), CO (PGX913), and Probe Disconnected (PGX905).
  • Page 10 Power Supply - North America after enrollment. Transformer: DSC PTD1640U, PTD1640 IMPORTANT! Ensure you have the following information available before contacting Primary: 120V, 60Hz Class II Customer Support : Secondary: 16.5VAC, 40VA Max.
  • Page 11 PowerSeries Neo Installation Guide Normal and high current battery charge options Supervision for loss of primary power source (AC fail), battery Supervised battery charging circuit loss or battery low voltage (battery trouble) with indication provided on the keypad Current draw (panel): Internal clock locked to AC power frequency 85mA (nominal) 2A(Max) Operating Environmental Conditions...
  • Page 12 Programming Directory This section provides a list of all available programming options in numerical order. To program, access Installer Programming mode by keying in [*][8] [Installer Code]. Use the scroll keys < > to navigate through the menus or jump directly to a specific section by keying in a section number and pressing [*].
  • Page 13 PowerSeries Neo Installation Guide 000 – Main Bell Mask 02 – Timed Output Keypad Lockout Attempts 3 – Armed State PGM ON at End Fire Alarm ✔ 04 – Service Required ✔ (000) of Exit Delay CO Alarm ✔ 05 – Loss of Clock ✔ Keypad Lockout Duration 4 –...
  • Page 14 PowerSeries Neo Installation Guide 05 – Panel Battery Absent ✔ 4 – Tamper Inhibit Arm 006 – No Activity Arming Timer 05 – Zone Expander 5 – Real Time Clock Option (000) Supervisory Alarm Restore 06 – Panel Battery Absent ✔...
  • Page 15 PowerSeries Neo Installation Guide 02 – Module AC Trouble 04 – Alt. Comm Receiver 2 001– Communicator Format - 1 – Phone Number Account Code Restore ✔ Supervision Failure Restore Receiver 1 2 – 6-Digit Account Code ✔ 03 – Module Battery Trouble 002–...
  • Page 16 PowerSeries Neo Installation Guide 01 – Sunday 001 - 128 – Station Assignment 1 - Siren Label (LCD only) 021 – Keypad Option 1 1 – [F] Key Enabled ✔ 02 – Monday 128 (00) Keypads 2 – [M] Key Enabled ✔ 03 –...
  • Page 17 SOFTWARE PRODUCT, are owned by Ltd. (“DSC”), the manufacturer of the integrated security DSC or its suppliers. You may not copy the printed materials systems and the developer of the software and any related 103 – Delete HSM2208 accompanying the SOFTWARE PRODUCT.
  • Page 18 PowerSeries Neo Installation Guide Zone Record Zone Label Location Type Attribute Zone Label Location Type Attribute - 18 -...
  • Page 19 PowerSeries Neo Installation Guide Zone Label Location Type Attribute Zone Label Location Type Attribute Module Record Module Type Slot Serial Number Module Type Slot Serial Number Wireless Device Record Device Type Zone Serial Number Device Type Zone Serial Number Installer-Defined Access Codes 001 –...
  • Page 20 PowerSeries Neo Installation Guide Make sure that all border doors and windows are easily opened. Ensure that Locating Detectors and Escape Plan they are not painted shut, and that their locking mechanisms operate smoothly. The following information is for general guidance only and it is recommended that local If opening or using the exit is too difficult for children, the elderly or han- fire codes and regulations be consulted when locating and installing smoke and CO dicapped, plans for rescue should be developed.
  • Page 21 FCC COMPLIANCE STATEMENT DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122 CAUTION: Changes or modifications not expressly approved by Digital Additional Information Connection to party line service is subject to state tariffs.
  • Page 22 A code shall be required for bypassing (section [023], option 4 shall be ON) Trouble beeps shall be enabled (section [022], option 7 shall be ON) configurations (Refer to the ULC Installation Information Sheet, DSC AC trouble indication LED shall be enabled (Keypad Programming, section...
  • Page 23 PowerSeries Neo Installation Guide Aux Loading and Battery Selection UL Resi Fire HS2128/HS2064/ UL Residential Burg UL Home Health Care EN50131 HS2032/HS2016 UL Commercial Burg ULC Fire Monitoring ULC Residential Burg ULC Resi Fire Grade 2/Class II Board current draw 85mA ULC Com Burg Max AUX (NSC) current 0.7A...
  • Page 24 PowerSeries Neo Installation Guide SIA False Alarm Reduction Installations: Quick Reference Minimum required system consists of one Control unit model HS2128 or HS2064 or HS2032 or HS2016 and any one of the compatible listed keypads: HS2LCDRF9, HS2LCDRFP9, HS2ICNRF9, HS2ICNRFP9, HS2LCD, HS2LCDP, HS2ICN, HS2ICNP, HS2LED HS2TCHP. The following wireless keys can also be used in SIA compatible installations: PG9929, PG9939,PG9949.
  • Page 25 PowerSeries Neo Installation Guide SIA Feature Programming Comments Range/Default Requirement Section Range:45- 255 Exit Time Required seconds Access to Entry and Exit delays and Bell Time Out for the system. [005]>[001], option 3 (programmable) Default: 60 sec. Exit Delay Restart Opening a Delay zone door after it has already been opened and closed during an exit delay restarts the Default: Enabled Required...
  • Page 26 DSC. Custom products are only warranted to the extent that Out of Warranty Repairs they do not function upon delivery. In such cases, DSC can replace or credit at its option. Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to its factory according to the following conditions.
  • Page 27 PowerSeries Neo Installation Guide environment, usage and type. Ambient conditions such as high humidity, high or low should include all sensing devices, keypads, consoles, alarm indicating devices and any temperatures, or large temperature fluctuations may reduce the expected battery life. other operational devices that are part of the system.
  • Page 28 Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative. © 2015 Tyco Security Products All Rights Reserved. Tech Support: 1-800-387-3630 (Canada & U.S.) or 905-760-3000 www.dsc.com...