Page 1
ORIGINAL INSTRUCTIONS Cordless Surface Cleaner RSC1840 OSC1800...
Page 2
Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modification.
Safety, performance, and dependability have been given ■ When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a top priority in the design of your cordless surface cleaner. cord suitable for outdoor use reduces the risk of electric shock.
Page 4
■ Store idle power tools out of the reach of children SERVICE and do not allow persons unfamiliar with the power ■ Have your power tool serviced by a qualified repair tool or these instructions to operate the power tool. person using only identical replacement parts.
■ For transportation in vehicles, secure the product ADDITIONAL SAFETY WARNINGS against movement or falling to prevent injury to persons or damage to the product. WARNING TRANSPORTING LITHIUM BATTERIES Some regions have regulations that restrict the use of Transport the battery pack in accordance with local and the product.
RISK REDUCTION Beware of thrown or flying objects. Keep all bystanders, especially children It has been reported that vibrations from hand-held tools and pets, at least 15 m away from the may contribute to a condition called Raynaud’s Syndrome. operating area. Symptoms may include tingling, numbness, and blanching of the fingers, usually apparent upon exposure to cold.
GETTING STARTED Always wear safety goggles or safety glasses with side Remove the adjustment knob and install the auxiliary handle. shields when operating the product. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.
Page 11
GETTING STARTED GETTING STARTED Tighten the adjustment knob and secure the auxiliary Release the telescoping latch and adjust the shaft. Secure Insert the roller brush attachment until the attachment Insert the roller brush. handle. the telescoping latch into place. release button clicks into place. NOTE: The auxiliary handle can be tilted 180°.
Page 13
OVERVIEW Cleaning the roller brush Operating the cleaner p.12 p.14 Replacing the roller brush Storing the cleaner p.16 p.17...
OPERATION OPERATING THE CLEANER WARNING: Always use two hands to operate the product. Hold the product with the right hand on the rear handle and the left hand on the front handle. WARNING: Remove hands and feet from the moving attachment at all times and especially when switching on the motor.
Page 15
OPERATION 3. Place the product parallel on the surface. Glide the product over the surface until the required result is achieved. NOTE: Use patio and deck cleaning detergents with the product for better results.
Page 16
MAINTENANCE CLEANING THE ROLLER BRUSH 1. Remove the battery pack. 2. Press the attachment release button, and remove the roller brush attachment. 3. Remove the roller brush. 4. Clean the roller brush attachment with a soft, dry cloth. NOTE: Keep the roller brush attachment away from corrosive agents, such as garden chemicals and de-icing salts.
Page 17
MAINTENANCE 5. Clean the roller brush with water. WARNING: Dry the roller brush thoroughly before use. 6. Insert the roller brush. Insert the attachment until the attachment release button clicks into place.
Page 18
MAINTENANCE REPLACING THE ROLLER BRUSH 1. Remove the battery pack. 2. Press the attachment release button, and remove the attachment. 3. Remove the roller brush. 4. Insert the new roller brush. Insert the attachment until the attachment release button clicks into place.
Page 19
STORAGE STORING THE CLEANER 1. Remove the battery pack. 2. Release the telescoping latch, and slide the upper shaft downward. 3. Secure the telescoping latch. 4. Loosen the knob, and tilt the handle toward the shaft. Tighten the knob to secure.
Page 20
STORAGE 5. Store the product in a cool, dry, and well- ventilated place that is inaccessible to children and away from sources of ignition.
PRODUCT SPECIFICATIONS REPLACEMENT PARTS Cordless Surface Cleaner Roller brush assembly RAC815 Model RSC1840/OSC1800 Roller brush RAC816 Voltage 18 V d.c. VIBRATION LEVEL Speed (with roller brush attachment) 940 ± 10% min The declared vibration value has been measured with a...
Page 24
Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC 3149, Melbourne, Australia Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South, RYOBI is a trademark of Ryobi Limited, Highbrook, Auckland 2013, New Zealand and is used under license. 961480065-01...