V2 WES-BASE Manual
  1. Manuals
  2. Brands
  3. V2 Manuals
  4. Remote Control
  5. WES-BASE
  6. Manual
V2 WES-BASE Manual

V2 WES-BASE Manual

Radio control system for safety edges
Hide thumbs Also See for WES-BASE:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
WES-BASE
SISTEMA PER IL CONTROLLO VIA RADIO DELLE
I
COSTE DI SICUREZZA
RADIO CONTROL SYSTEM FOR SAFETY EDGES
GB
SYSTÈME POUR LE CONTRÔLE PAR RADIO DES
F
BARRES PALPEUSES DE SÉCURITÉ
SISTEMA PARA EL CONTROL VÍA RADIO DE LAS
E
BANDAS DE SEGURIDAD
SISTEMA PARA O CONTROLO VIA RÁDIO DAS
P
COSTAS DE SEGURANÇA
FUNK-STEUERSYSTEM FÜR SICHERHEITSRIPPEN
D
SYSTEEM VOOR DE CONTROLE VAN
NL
VEILIGHEIDSLIJSTEN VIA RADIO
V2 S.p.A.
Corso Principi di Piemonte, 65/67
12035 RACCONIGI (CN) ITALY
tel. +39 01 72 81 24 11 - fax +39 01 72 84 050
info@v2home.com - www.v2home.com
IL n. 332
EDIZ. 09/03/2011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WES-BASE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for V2 WES-BASE

Summary of Contents for V2 WES-BASE

  • Page 1 V2 S.p.A. Corso Principi di Piemonte, 65/67 12035 RACCONIGI (CN) ITALY IL n. 332 tel. +39 01 72 81 24 11 - fax +39 01 72 84 050 EDIZ. 09/03/2011 info@v2home.com - www.v2home.com WES-BASE SISTEMA PER IL CONTROLLO VIA RADIO DELLE...

  • Page 3: Technical Information

    • All maintenance or programming operations should be DESCRIPTION conducted exclusively by qualified staff. WES (Wireless Edge System) is the new V2 system allowing safety edges to be controlled by radio. The installation, testing and commissioning of door and gate...

  • Page 4: Base Unit Installation

    BASE UNIT INSTALLATION PLEASE NOTE: The device should only be installed after having disconnected the power supply for the control unit to which the WES base unit is connected. 1. Install the base unit near the control unit; fix the casing using the specific fixing lugs A 2.

  • Page 5: Dip Switches

    BASE UNIT ELECTRICAL CONNECTIONS BASE UNIT CONTROL UNIT POWER+ System power - positive pole (12 / 24 Vdc-ac) POWER- System power – accessory supply COMMON Common safety input OUT1 Unit 1 edge input OUT2 Unit 2 edge input BAT LOW Can be used to indicate low battery level START Photocell TX supply...
  • Page 6 RADIO CHANNEL CONFIGURATION When the network is not configured, the base unit monitors the 16 possible radio channels and registers activity present in the environment; for establishment of a new network, it is appropriate to select a channel on which there is low radio activity, in order to avoid interference.
  • Page 7 LED SIGNALS ON THE BASE UNIT CONDITION GREEN LED (RADIO) RED LED (ALARM) LED OUT 1 LED OUT 2 LED BAT LOW DIP-SWITCH 8 OFF • Flashes slowly • Off • Off • Off • Off NETWORK NOT CONFIGURED • A brief flash with •...

  • Page 8: Fault Finding Procedure

    FAULT FINDING PROCEDURE Conduct fault-finding with the system off (door closed). STEP Action Test Diagnosis Open the base cover and observe A sensor has a low battery; find the sensor with Is the LOW BAT LED on? the red LED the flashing LED Communication problems between the sensors Is the ALARM LED on and fixed?

Table of Contents