1. Manuals
  2. Brands
  3. Sony Ericsson Manuals
  4. Cell Phone
  5. J210i
  6. Working instruction, mechanical

Sony Ericsson J210i Working Instruction, Mechanical

Hide thumbs Also See for J210i:
Table of Contents

Advertisement

Quick Links

Download this manual
Working Instructions - mechanical
Applicable for J210i
CONTENTS
1
Read this first! ......................................................................................... 2
2
Introduction.............................................................................................. 3
3
Repair actions.......................................................................................... 4
3.1
3.2
Front Cover ass'y .......................................................................................8
3.3
Keypad .....................................................................................................10
3.4
PCB.... .....................................................................................................11
3.5
Display .....................................................................................................13
3.6
Name Plate ..............................................................................................15
3.7
Microphone ass'y .....................................................................................16
3.8
Earphone & Earphone Gasket .................................................................17
3.9
Joystick Button ass'y ................................................................................18
3.10 Tape Shield Can.......................................................................................19
3.11 Keypad Dome ..........................................................................................20
3.12 Vibrator.....................................................................................................21
3.13 Battery Connector ....................................................................................22
3.14 Loudspeaker ass'y ...................................................................................23
3.15 Strap Insert Plate .....................................................................................24
3.16 IrDA Window ............................................................................................25
3.17 Water Damage Indicator ..........................................................................26
3.18 Frame ass'y..............................................................................................27
4
Label ....................................................................................................... 28
5
Revision History .................................................................................... 29
3/00021-1/FEA 209 544/107A
Company Internal
Sony Ericsson Mobile Communications AB
J210 Working Instructions - mechanical

Advertisement

Table of Contents
loading

Related Manuals for Sony Ericsson J210i

Summary of Contents for Sony Ericsson J210i

  • Page 1: Table Of Contents

    3.13 Battery Connector ..................22 3.14 Loudspeaker ass’y ...................23 3.15 Strap Insert Plate ..................24 3.16 IrDA Window ....................25 3.17 Water Damage Indicator ................26 3.18 Frame ass’y....................27 Label ....................... 28 Revision History ..................29 3/00021-1/FEA 209 544/107A  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 2: Read This First

    Flash movies played by the Flash Player application. NOTE! Flash Player ver. 6 or later must be installed on the computer. The Flash Player can be downloaded free of charge from www.macromedia.com. 3/00021-1/FEA 209 544/107A 2(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 3: Introduction

    J210 Working Instructions - mechanical 2 Introduction SPECIAL TOOLS No new special tools are introduced but a few other Sony Ericsson tools are required: • NTZ 112 459 Torque screwdriver (or equivalent) to 11 Ncm ± 6 % • NTZ 112 288 Torx bit no.

  • Page 4: Repair Actions

    J210 Working Instructions - mechanical 3 Repair actions FRONT/REAR VIEW 3/00021-1/FEA 209 544/107A 4(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 5: Battery Cover Ass'y & Battery

    Use your thumbs to slide down the battery cover, just until the antenna flex film becomes visible. Remove the battery cover by lifting it up. Push the battery slightly forward, 3/00021-1/FEA 209 544/107A 5(29)  Company Internal Sony Ericsson Mobile Communications AB...
  • Page 6 Battery Cover ass’y & Battery continued and at the same time pull upwards to remove it. ASSEMBLY Insert the two battery pegs, into these slots, and push forward, 3/00021-1/FEA 209 544/107A 6(29)  Company Internal Sony Ericsson Mobile Communications AB...
  • Page 7 Place the battery cover as shown in this picture, so that that the antenna flex film becomes visible. Hold the phone like this and slide the battery cover until it gets closed. 3/00021-1/FEA 209 544/107A 7(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 8: Front Cover Ass'y

    The front cover can then be lifted off. 3/00021-1/FEA 209 544/107A 8(29)  Company Internal Sony Ericsson Mobile Communications AB...
  • Page 9 Tighten four new screws with 11 Ncm torque using torx bit no. 6 in order 1-4, as indicated in the adjacent picture. Follow the Assembly instructions of section 3.1 3/00021-1/FEA 209 544/107A 9(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 10: Keypad

    Follow the Removal instructions of sections 3.1 – 3.2 Use the tweezers to remove the keypad. ASSEMBLY Use the tweezers to install the keypad. Follow the Assembly instructions of sections 3.2 – 3.1 3/00021-1/FEA 209 544/107A 10(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 11: Pcb

    PCB becomes released from the snap hook of the frame. Do the same thing on the opposite side. Remove the PCB. 3/00021-1/FEA 209 544/107A 11(29)  Company Internal Sony Ericsson Mobile Communications AB...
  • Page 12 Press down on each side to snap the hooks (red circles), and check that the PCB is securely attached. Follow the Assembly instructions of sections 3.3 – 3.1 3/00021-1/FEA 209 544/107A 12(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 13: Display

    There are four snap hooks holding the display onto the PCB. Use your fingers to release the hooks in order 1-4. ASSEMBLY There are two guiding holes on the PCB to facilitate the installation of the display. 3/00021-1/FEA 209 544/107A 13(29)  Company Internal Sony Ericsson Mobile Communications AB...
  • Page 14 Use your fingers to connect the board-to-board connector to the PCB. Follow the Assembly instructions of sections 3.4 – 3.1 3/00021-1/FEA 209 544/107A 14(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 15: Name Plate

    Be careful not to scratch the front cover! Gently remove the name plate by using tweezers. ASSEMBLY Clean the surface with isopropyl alcohol. Attach a new name plate by using tweezers and/or your fingers. 3/00021-1/FEA 209 544/107A 15(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 16: Microphone Ass'y

    Use your fingers or tweezers to install the microphone. Gently press on the microphone until it reaches the bottom of the cavity. Follow the Assembly instructions of sections 3.2 – 3.1 3/00021-1/FEA 209 544/107A 16(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 17: Earphone & Earphone Gasket

    Right Use tweezers to place the earphone inside the cavity. Press on the earphone to make it securely attached. Follow the Assembly instructions of sections 3.2 – 3.1 3/00021-1/FEA 209 544/107A 17(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 18: Joystick Button Ass'y

    Check that the button cavity is in the position shown in this picture. Follow the Assembly instructions of sections 3.3 – 3.1 3/00021-1/FEA 209 544/107A 18(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 19: Tape Shield Can

    Clean the surface with isopropyl alcohol. Attach a new tape shield can to be aligned with the red line. Follow the Assembly instructions of sections 3.4 – 3.1 3/00021-1/FEA 209 544/107A 19(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 20: Keypad Dome

    Make sure that the guiding holes of the keypad dome are placed above the guiding holes of the PCB. Follow the Assembly instructions of sections 3.4 – 3.1 3/00021-1/FEA 209 544/107A 20(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 21: Vibrator

    Use the tweezers to put the vibrator into the frame cavity. Press on the vibrator until it reaches the bottom of the cavity. Follow the Assembly instructions of sections 3.4 – 3.1 3/00021-1/FEA 209 544/107A 21(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 22: Battery Connector

    Position the battery connector at a 30 angle. Use your fingers to push on the battery connector until it fits properly. Follow the Assembly instructions of sections 3.4 – 3.1 3/00021-1/FEA 209 544/107A 22(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 23: Loudspeaker Ass'y

    Remove the protection foil and place the loudspeaker into the cavity as shown in picture. Press on the loudspeaker until it is securely attached. Follow the Assembly instructions of sections 3.4 – 3.1 3/00021-1/FEA 209 544/107A 23(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 24: Strap Insert Plate

    ASSEMBLY Use the tweezers to grab the strap insert plate, then slide it inwards. Follow the Assembly instructions of sections 3.4 – 3.1 3/00021-1/FEA 209 544/107A 24(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 25: Irda Window

    Push from the inside of the frame on the IrDA window until it snaps into its proper position. Follow the Assembly instructions of sections 3.4 – 3.1 3/00021-1/FEA 209 544/107A 25(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 26: Water Damage Indicator

    ASSEMBLY carefully Clean the surface with isopropyl alcohol and apply a new water damage indicator using tweezers. Follow the Assembly instructions of sections 3.4 – 3.1 3/00021-1/FEA 209 544/107A 26(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 27: Frame Ass'y

    3.12 – 3.17 Replace the frame with a new one. Follow the Assembly instructions of sections 3.12 – 3.17 (as assembled in adjacent picture) & 3.4 – 3.1 3/00021-1/FEA 209 544/107A 27(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 28: Label

    Check that the printing is ok. • Take the new label and place it onto the frame as in the picture. Make sure the label is placed in its proper position. 3/00021-1/FEA 209 544/107A 28(29)  Company Internal Sony Ericsson Mobile Communications AB...

  • Page 29: Revision History

    J210 Working Instructions - mechanical 5 Revision History Rev. Date Changes / Comments 2005-08-25 Initial release 3/00021-1/FEA 209 544/107A 29(29)  Company Internal Sony Ericsson Mobile Communications AB...

Table of Contents