Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CAB ST4 Series
Summary of Contents for CAB ST4 Series
- Page 1 Operator's Manual Stacker with Cutter Made in Germany...
- Page 2 Edition: 03/2016 - Part No. 9008838 Copyright This documentation as well as translation hereof are property of cab Produkttechnik GmbH & Co. KG. The replication, conversion, duplication or divulgement of the whole manual or parts of it for other intentions than its original intended purpose demand the previous written authorization by cab.
-
Page 3: Table Of Contents
Table of Contents Introduction ............................4 Notes ................................ 4 Intended Use ............................4 Safety Instructions ............................ 5 Environment ............................. 6 Technical Data ............................6 Device Overview ............................6 Installation .............................. 8 Unpacking ..............................8 Preparing the Printer ..........................8 Mounting the Stacker to the Printer ......................9 Adapting the Stacker to the Media Size .................... -
Page 4: Introduction
• The device is intended exclusively as a peripheral device for the cab printers of the A+, XC and XD series for cutting and stacking suitable materials that have been approved by the manufacturer. Any other use or use going beyond this shall be regarded as improper use. -
Page 5: Safety Instructions
Introduction Safety Instructions • Disconnect the printer from the electrical outlet before mounting or removing the stacker (2). • When using the stacker with printers of the A+ series the stacker protrudes the base plate of the printer. Therefore the system must be positioned at the edge of the platform or on a mounting unit. Position the system in such a way that a risk of tilting will be avoided. -
Page 6: Environment
Introduction Environment Obsolete devices contain valuable recyclable materials that should be sent for recycling. Send to suitable collection points, separately from residual waste. The modular construction of the printer enables it to be easily disassembled into its component parts. ... - Page 7 Introduction 1 Cover 2 Knurled screw 3 Table 4 Handle for height displacement of the table 5 Upper blade 6 Lower blade 7 Safety cover 8 Scale 9 Side plate (movable) 10 Side plate (movable) 11 Safety cover Figure 3 Overview ST4/M 2 Knurled screw 12 Media Guide...
-
Page 8: Installation
Installation Unpacking Check stacker for damage which may have occurred during transport. Check delivery for completeness. Contents of delivery: • Stacker with cutter • Documentation Note! Please keep the original packaging in case the printer must be returned. Attention! The device and printing materials will be damaged by moisture and wetness. -
Page 9: Mounting The Stacker To The Printer
Installation Mounting the Stacker to the Printer Attention! Disconnect the printer from the electrical outlet before mounting or removing the stacker. Caution! Risk of tilting. When using the stacker with printers of the A+ series the stacker protrudes the base plate of the printer. Therefore the system must be positioned at the edge of the platform or on a mounting unit. -
Page 10: Adapting The Stacker To The Media Size
Installation Adapting the Stacker to the Media Size Caution! Risk of injury! With inappropriate tables and safety covers the reliability and machinery safety cannot be guaranteed. Equip the stacker only with a table designated for the media to be used and the matching safety covers. 2.4.1 Adjusting the Side Plates 1 2 3 4... -
Page 11: Mounting The Safety Covers
Installation 2.4.3 Mounting the Safety Covers Caution! Risk of injury! Without safety covers or with improperly mounted safety covers the reliability and machinery safety cannot be guaranteed. Equip the stacker only with safety covers designated for the media to be used. ... -
Page 12: Printer Configuration
Printer Configuration Once the stacker is connected to the printer, the printer will automatically recognize it on turn on. The printer can be configured to suit the individual requirements of cut mode in the „Setup“ menu. When the stacker is installed, the „Cutter“ menu will appear. Note! For detailed instructions for configuration Configuration Manual of the printer. -
Page 13: Loading Material
Loading Material Load transfer ribbon and endless material as described in the Operator's Manual of the printer Use the tear-off mode information for loading endless material for cut mode. Place the media strip between the printhead and the drive roller, so that the front edge of the strip reaches through the cutter. -
Page 14: Maintenance
Maintenance The maintenance is limited to monthly cleaning of the device. The most important is the cleaning of the cutter blades. Caution! Risk of injury! Disconnect the printer from the electrical outlet to avoid unintended cutter moves. Carefully handle the cutter. The cutter blades are sharp. Figure 11 Cleaning the cutter 1. -
Page 15: Error Messages / Problem Solutions
Error Messages / Problem Solutions General information Operator's Manual of the printer. Specific Error Messages concerning the Stacker with Cutter Remedy Error message Cause Cutter jammed Material too thick Change material Bracket on the upper blade collides Use safety covers matching to the table width. with safety cover Re-adjust the movable side plates. -
Page 16: Reference To The Eu Declaration Of Conformity
The Stackers with Cutter comply with the relevant fundamental regulations of the EU Rules for Safety and Health: • Directive 2014/30/EU relating to electromagnetic compatibility • Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment EU Declaration of Conformity https://www.cab.de/media/pushfile.cfm?file=2720 ...
Need help?
Do you have a question about the ST4 Series and is the answer not in the manual?
Questions and answers