Bosch Professional GAS 18V-10 L Original Instructions Manual page 16

16 | English
Cordless wet/dry dust extractor
Protection class
Container volume (gross)
Net volume (liquid)
A)
Max. pressure
B)
– Vacuum
– Turbine
A)
Max. flow rate
B)
– Vacuum
– Turbine
Dust class
Weight according to
EPTA-Procedure 01:2014
Recommended ambient
temperature during charging
Permitted ambient temperature
C)
during operation and during
storage
Recommended batteries
Recommended chargers
Operating time per battery
charge
A) Depends on battery in use
B) measured with vacuum hose (13) and curved nozzle (15)
C) Limited performance at temperatures <0 °C
Noise/vibration information
Noise emission values determined according to
EN 60335-2-69.
Typically the A-weighted sound pressure level of the dust ex-
tractor is 79 dB(A). Uncertainty K = 2 dB. The noise level
when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60335-2-69: a
2
K = 1.5 m/s .
Assembly
Charging the Battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your dust extractor.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
1 609 92A 551 | (02.07.2019)
The lithium-ion battery can be charged at any time without
GAS 18V-10 L
reducing its service life. Interrupting the charging process
IP X4
does not damage the battery.
l 10
The lithium-ion battery is protected against deep discharge
l 6
by the "Electronic Cell Protection (ECP)". A protective circuit
switches the cordless dust extractor off when the battery is
drained.
hPa 90
u
hPa 115
A significantly reduced operating time after charging indic-
l/s 24
ates that the battery has deteriorated and must be replaced.
3
m /h 86
Follow the instructions on correct disposal.
l/s 34
Battery charge indicator
3
m /h 122
After the dust extractor is switched on, the five green LEDs
L
of the battery charge indicator (4) will light up individually
kg 5.1–6.1
one after another in ascending and descending order. Then
the LEDS will indicate the state of charge of the bat-
°C 0 to +35
tery (20).
Inserting and Removing the Battery
°C −20 to +50
(see figures A1−A2)
u
GBA 18V...
ProCORE18V...
GAL 18... u
GAX 18...
GAL 36...
– Press the release button (11) to open the battery com-
min/Ah 4
– Slide the battery (20) into the battery bay (19) until it
– To remove the battery (20), press the release but-
– Close the battery compartment cover (12).
Changing the Battery Compartment Cover
(see figures A3−A5)
If you wish to use a battery ProCORE18V 12Ah, the battery
compartment cover (12) can then no longer be closed. In
this case, the battery compartment cover (12) can be re-
placed with a battery compartment cover (34) designed for
this purpose.
2
< 2.5 m/s ,
h
Even with the small battery compartment cover, the protec-
tion class remains unchanged.
Removing the Battery Compartment Cover
(see figure A3)
Remove the battery (20) from the battery bay (19).
Remove the two fastening screws (33) (ST4×12) with a
cross-headed screwdriver PH1 and take off the battery com-
partment cover (12).
Do not continue to press the on/off button after the
dust extractor has automatically switched itself off.
This can damage the battery.
Do not use force to insert the battery. The battery is de-
signed in such a way that it can only be inserted into the
dust extractor when it is in the right position.
Keep the battery compartment and the battery bay clean
and dry at all times to ensure good, safe operation.
partment cover (12).
audibly clicks into place.
ton (21) on the battery and pull it out of the battery
bay (19).
Bosch Power Tools