Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Indexator G-184
Summary of Contents for Indexator G-184
- Page 1 User manual User User LINK G–184 MPBT1–80 swing damper MPBT1–100 swing damper MPB1–80 swing damper MPB1–100 swing damper MPB1–125 swing damper MPB1–184 swing damper Swingdamper MPB1-80 BC Swingdamper MPB1-100 BC Swingdamper MPB1-184 BC 5002823 en 1102 086 | 3847 | 2018-09-12...
-
Page 2: Table Of Contents
Maintenance overview ................15 Maintenance instructions ..............16 Repair instructions ................19 Removing product from crane tip and rotator ..........20 Technical data ..................21 MPB1-80/MPB1-80 BC/MPBT1-80, MPB1–100/MPB1–100 BC/MPBT1–100, MPB1–125, MPB1–184/MPB1–184 BC/G-184 ........21 © Indexator AB 1102 086 2018-09-12 15:16... -
Page 3: Introduction
Contact your local dealer for information about any changes. Copying this manual in whole or in part is not allowed without written authorisation from Indexator AB. The restriction applies to all forms of copying, including printing, digitising, etc. 1102 086 2018-09-12 15:16 ©... -
Page 4: Safety Instructions
Additional information is marked as below. Attention! N.B. is important additional information that helps you understand or carry out a particular action. © Indexator AB 1102 086 2018-09-12 15:16... -
Page 5: Product-Specific Warnings
Risk of personal injury. The torque from the adjustment device causes potential energy to build up, which can have an explosive effect if a screw is damaged. Stand to the side of the adjustment device when tightening. 1102 086 2018-09-12 15:16 © Indexator AB... -
Page 6: Safety
The risk area must be at least as big as the largest load, or as the width of the tool on a horizontal plane. The manufacturer must provide clear warnings about this. DANGER No personnel are permitted in the area under hanging loads/tools. It is a strictly prohibited area. © Indexator AB 1102 086 2018-09-12 15:16... - Page 7 Safety instructions Caution Risk of skin irritation/allergic reactions. There can be a number of chemical preparations on the product. Use protective gloves when handling. 1102 086 2018-09-12 15:16 © Indexator AB...
-
Page 8: Description
The product is a link or a swing damper. The product is designed to be fitted between the rotator and the crane tip. The product is designed to be used for positioning freely-hanging vertical loads. Image 1 MPB1 Link Brake kit © Indexator AB 1102 086 2018-09-12 15:16... - Page 9 Description Image 2 KPL hose control Hose control Hose reel Tube Image 3 MPB1–184 Link Brake kit KPL hose control 1102 086 2018-09-12 15:16 © Indexator AB...
-
Page 10: Brake Kit (Swing Damper Only)
The brake kit consists of the brake block, brake discs, bearings, adjustment device and centering device. Centering device The centering device holds the brake kit in place. The centering device is fitted through the brake kit and consists of a centre tube and sliding sleeves. © Indexator AB 1102 086 2018-09-12 15:16... -
Page 11: Installation
Image 5 Assemble the link with the rotator positioned incorrectly. 4. Secure the locking rings with the distance Locking ring Distance ring rings (x 2). Turn the groove towards the Locating flat centre of the link. Rotator 1102 086 2018-09-12 15:16 © Indexator AB... - Page 12 Image 6 Assembling the sliding sleeve Sliding sleeve Important Centre tube Risk of product damage. Slightly lift the brake block before the centre tube has been inserted, otherwise the brake block ball bearings will be damaged. © Indexator AB 1102 086 2018-09-12 15:16...
- Page 13 4. Adjustment screw and locking ring) in the centre tube and Adjusting nut tighten the adjustment screw to the Stop cleat adjustment nut using a 10 mm hexagon wrench. Tightening torque 60 Nm. 1102 086 2018-09-12 15:16 © Indexator AB...
-
Page 14: Settings And Adjustments
When refitting the cup springs, they must be placed in the same way as existing cup springs. Adjusting the weighing instrument This is carried out according to the documentation from the weighing instrument's supplier. © Indexator AB 1102 086 2018-09-12 15:16... -
Page 15: Maintenance
Brake discs Check for wear, clean components, and make replacements where necessary Sleeves and centre tube Lubrication Attachment Check for cracks, change if necessary Bushings Check the size of play, possible change 1102 086 2018-09-12 15:16 © Indexator AB... -
Page 16: Maintenance Instructions
60 Nm. Every 50 hours Image 9 Bushings Bushings Connect a grease gun with sufficient lubrication to the grease nipples. Keep on pumping until you see grease between the pin and the link. © Indexator AB 1102 086 2018-09-12 15:16... - Page 17 Image 11 Rotation of bearings in brake block Play Make sure that there is no abnormal play in the link bearings. A difference of more than 1.5mm needs to be resolved. Image 12 Checking play 1102 086 2018-09-12 15:16 © Indexator AB...
- Page 18 Check that there are no cracks on the product's upper or lower attachment. Bushings By moving the swing damper to the side, make sure that there is no play between the scale's bushings and pins. If there is a play, the bushings must be replaced. © Indexator AB 1102 086 2018-09-12 15:16...
-
Page 19: Repair Instructions
3. Remove the lower brake kit. 4. Fitting the new brake kit must be done as per the instructions for installing the lower brake kit. Bearings in brake kit These have a separate repair kit. Contact your dealer. 1102 086 2018-09-12 15:16 © Indexator AB... -
Page 20: Removing Product From Crane Tip And Rotator
4. Remove the upper pins so that the product is loosened from the crane tip. 5. Remove the lower pins so that the product is loosened from the rotator. 6. Remove the product. © Indexator AB 1102 086 2018-09-12 15:16... -
Page 21: Technical Data
Technical data Technical data MPB1-80/MPB1-80 BC/MPBT1-80, MPB1–100/MPB1–100 BC/MPBT1–100, MPB1–125, MPB1–184/MPB1–184 BC/G-184 Image 15 MPB1–80/ MPB1–100/ MPB1–125 MPB1–184/ MPB1–80 BC/ MPB1–100 BC/ MPB1–184 BC/ MPBT1-80 MPBT1–100 G-184 80 mm 100 mm 125 mm 184 mm 240 mm 240 mm 240 mm 240 mm 180°... - Page 22 Indexator Rotator Rotator Systems Systems Indexator Indexator Rotator Systems Tel + 46 933 148 00 rotator@indexator.com www.indexator.com...