Related Manuals for Indexator LINK Series
Summary of Contents for Indexator LINK Series
- Page 1 User manual User User LINK Swing damper -184 M52 3T –184 –184 HD S-184 HD Swing damper -184 HD Swing damper S-184 HD 5002822 en 1102 029 | 3777 | 2017-08-21...
-
Page 2: Table Of Contents
Brake kit (swing damper only) ..............13 Installation....................15 Maintenance.................... 17 Maintenance overview ................17 Repair instructions ................19 Removing product from crane tip and rotator ..........20 Technical data ..................21 Link –184 ..................21 © Indexator AB 1102 029 2017-08-21 13:36... -
Page 3: Introduction
Contact your local dealer for information about any changes. Copying this manual in whole or in part is not allowed without written authorisation from Indexator AB. The restriction applies to all forms of copying, including printing, digitising, etc. 1102 029 2017-08-21 13:36 ©... -
Page 4: Safety Instructions
Additional information is marked as below. Attention! N.B. is important additional information that helps you understand or carry out a particular action. © Indexator AB 1102 029 2017-08-21 13:36... -
Page 5: Product-Specific Warnings
Risk of personal injury. The torque from the adjustment device causes potential energy to build up, which can have an explosive effect if a screw is damaged. Stand to the side of the adjustment device when tightening. 1102 029 2017-08-21 13:36 © Indexator AB... -
Page 6: Safety
The risk area must be at least as big as the largest load, or as the width of the tool on a horizontal plane. The manufacturer must provide clear warnings about this. DANGER No personnel are permitted in the area under hanging loads/tools. It is a strictly prohibited area. © Indexator AB 1102 029 2017-08-21 13:36... -
Page 7: Indexator Ab
Safety instructions Caution Risk of skin irritation/allergic reactions. There can be a number of chemical preparations on the product. Use protective gloves when handling. 1102 029 2017-08-21 13:36 © Indexator AB... -
Page 8: Description
The product is a link or a swing damper. The product is designed to be fitted between the rotator and the crane tip. The product is designed to be used for positioning freely-hanging vertical loads. Image 1 Link Link Hose control © Indexator AB 1102 029 2017-08-21 13:36... - Page 9 Description Image 2 Swing damper Link Hose control Brakes 1102 029 2017-08-21 13:36 © Indexator AB...
-
Page 10: Link
Description Link Image 3 Link Link Hose control Spacer Hose reel Tube © Indexator AB 1102 029 2017-08-21 13:36... -
Page 11: Swing Damper
Description Swing damper Image 4 Swing damper Link Hose control Spacer Hose reel Tube 8. Brake disc Brake block 1102 029 2017-08-21 13:36 © Indexator AB... -
Page 12: Swing Damper M52
Description Swing damper M52 Image 5 Link Hose control Spacer Hose reel Tube 8. Brake disc Brake block © Indexator AB 1102 029 2017-08-21 13:36... -
Page 13: Description
Hold the flange nut and tighten the screw. The maximum tightening torque for the screw joint is 30 Nm. Wear increases if tightening torque too high. After adjusting, the screw joint is locked by the locking nut. 1102 029 2017-08-21 13:36 © Indexator AB... - Page 14 Replacing brake block M52 Loosen the screw joint. Remove the cup springs and replace blocks. Reinstall in reverse order. © Indexator AB 1102 029 2017-08-21 13:36...
-
Page 15: Installation
Installation Installation Image 10 Image 11 1102 029 2017-08-21 13:36 © Indexator AB... - Page 16 Installation Image 12 © Indexator AB 1102 029 2017-08-21 13:36...
-
Page 17: Maintenance
Check the size of play, possible change Tighten the nut Every 600 hours Brake kit Check for wear, clean components, and make replacements where necessary Brake discs Check for wear, clean components, and make replacements where necessary 1102 029 2017-08-21 13:36 © Indexator AB... - Page 18 Maintenance Connect a grease gun with sufficient lubrication to the grease nipples. Keep on pumping until you see grease between the pin and the link. Image 13 Bushings Image 14 © Indexator AB 1102 029 2017-08-21 13:36...
-
Page 19: Repair Instructions
If there is a fracture in the attachment, the link must be replaced. Contact your dealer for more information. Bushings 1. Disassemble the product. 2. Press out the bushings using a hydraulic press. 3. Press in the new bushings. 1102 029 2017-08-21 13:36 © Indexator AB... -
Page 20: Removing Product From Crane Tip And Rotator
3. Remove the upper pin so that the product is loosened from the crane tip. 4. Remove the upper pin so that the product is loosened from the rotator. 5. Remove the product. © Indexator AB 1102 029 2017-08-21 13:36... -
Page 21: Technical Data
240 mm DØ Ø35 Ø35 Ø35 Ø45 13,5 13,5 17.2 23,5 Weight (kg) 3 tonnes 10 tonnes 10 tonnes 16 tonnes Max. load Max. rotator size GV 6 GV 12 GV 12 GV 17S 1102 029 2017-08-21 13:36 © Indexator AB... - Page 22 S-184 HD 184 mm 184 mm 80 mm 100 mm 240 mm 240 mm DØ Ø35 Ø45 16.5 22,5 Weight (kg) 10 tonnes 16 tonnes Max. load GV 12 GV 17S Max. rotator size © Indexator AB 1102 029 2017-08-21 13:36...
- Page 23 © Indexator AB 1102 029 2017-08-21 13:36...
- Page 24 Indexator Rotator Rotator Systems Systems Indexator Indexator Rotator Systems Tel + 46 933 148 00 rotator@indexator.com www.indexator.com...