1. Manuals
  2. Brands
  3. Hawk Manuals
  4. Industrial Equipment
  5. HAWKJAW 100K-2GSR
  6. Operation, maintenance and service manual

Hawk HAWKJAW 100K-2GSR Operation, Maintenance And Service Manual

Hide thumbs Also See for HAWKJAW 100K-2GSR:
Table of Contents

Advertisement

Quick Links

Download this manual
HAWKJAW
OPERATION, MAINTENANCE
AND
SERVICE MANUAL
MODEL 100K-2GSR
Serial # 128-130
HAWK INDUSTRIES, INC.
1245 East 23rd Street
Long Beach, CA 9080
Phone: 562-424-0709
Fax: 562-490-9959
www.hawkindustries.com

Advertisement

Table of Contents
loading

Related Manuals for Hawk HAWKJAW 100K-2GSR

Summary of Contents for Hawk HAWKJAW 100K-2GSR

  • Page 1 HAWKJAW OPERATION, MAINTENANCE SERVICE MANUAL MODEL 100K-2GSR Serial # 128-130 HAWK INDUSTRIES, INC. 1245 East 23rd Street Long Beach, CA 9080 Phone: 562-424-0709 Fax: 562-490-9959 www.hawkindustries.com...

  • Page 2: Introduction

    Hawk has designed the HawkJaw with this same simple formula. FEATURES The HawkJaw 100K-2GSR is a hanging unit that will spin, make up and break out drill pipe. It is revolutionary because the tool spins and makes up drill pipe or breaks out and spins drill pipe in 12 seconds or less.

  • Page 3: Table Of Contents

    Table of Contents Introduction Table of Contents Warranty Specification Sheet Ordering Instructions Installation Hanging Cable Location HawkJaw Location Hanging Cable Requirements Hydraulic Requirements Air Requirements Raise/Lower Cylinder Hook - Up Winch Hook - Up Operation Start-up Procedure Adjust for Make Up Adjusting the Wrenches Adjusting the Spinner Position for Make Up...
  • Page 4 Table of Contents Changing the Hook Dies Hook Dies Changing the Heel Dies Top Wrench Heel Die Middle Wrench Heel Die Bottom Wrench Heel Die Spinner Maintenance Chain Lubrication Drive Roller Sprocket Bearings Chain Drive Shaft Bearing Spinner Grip Cylinders Spinner Mount Sliding Block Spinner Mount Sliding Tube Reducer Gear Box...
  • Page 5 Table of Contents 100K-2GJR Left Control Handle Assembly 100K-2GJR Right Control Handle Assembly 100K-2GJR Winch MountAssembly 100K-2GJR Spinner MountAssembly 100K-2GJR Stand Assembly 100K-2GJR Hawkjaw Spinner Assembly 100K-2GJR Pipe Stop Assembly 100K-2GJR Hydraulic Connections 100K-2GJR Spin Manifold Assembly 100K-2GJR Raise/Lower Cylinder Assembly 100K-2GJR Main Manifold Assembly 100K-2GJR Main Manifold Air Connections 100K-2GJR Left Control Handle Air Connections...

  • Page 6: Warranty

    This guarantee does not include the replacement of parts where failure occurred due to normal wear and tear or misuse of the tool. Defective parts must be inspected by Hawk Industries, at its Long Beach plant, before warranty can be honored. Customer must obtain an RGA# (Return of Goods Authorization) from the California, USA factory.

  • Page 7: Specification Sheet

    Specification Sheet DIMENSIONS DEPTH: 58 in. WIDTH: 50 in. HEIGHT: 100 in. PERFORMANCE AND POWER REQUIREMENTS TORQUE: 100,000 ft. lbs. MAXIMUM PIPE ROTATION: 50 degrees WRENCH SIZE RANGE: 4" 9 1/2" OD tool joints SPINNER SIZE RANGE: 3" 9 1/2" OD tube AIR POWER SOURCE: 100 psi @ 2-10 cfm...

  • Page 8: Ordering Instructions

    Ordering Instructions All parts must be ordered by giving the quantity needed, the full part number as listed in this manual under Part #, the unit serial number, the model number and part name. Example Model # Quantity Part # Serial # Part Name 061-20194...

  • Page 9: Installation

    Hanging Cable Location 1. Anchor the hanging cable to a point as close to the derrick crown as possible. The longer the hanging cable, the easier the HawkJaw is to move on and off the drill pipe. 2. Locate the cable hang point as high above the center of the rotary table as possible.

  • Page 10: Hanging Cable Requirements

    Hanging Cable Requirements 1. 5/8" diameter steel cable. 2. Appropriate hanging cable hardware for 5/8" diameter steel cable. 3. Enough cable length to suspend the Hanger Eye (HE) 20' ft. above the rig floor. 4. Enough cable length to allow the HawkJaw to rest on the rig floor 3'- 5' ft.

  • Page 11: Hydraulic Requirements

    4. 1 1/4" minimum Tank line. 500 psi The HawkJaw must receive clean hydraulic fluid. minimum hose working pressure. Running the HawkJaw without a Hawk approved filter (Part # 061-H25) and installed filter element 5. Hawk approved quick disconnects (Part # 061-H25A) voids the warranty and severely [Male: Part # 061-H52 (MQD).

  • Page 12: Air Requirements

    WARNING The HawkJaw must receive clean, dry air. Running the HawkJaw without a Hawk approved air filter (Part # 061-J29) voids the warranty and shortens component life. NOTE Make sure the larger air filter (Part # 061- J29) is mounted vertically with the red and black arrows on the cannisters pointing up.

  • Page 13: Raise/Lower Cylinder Hook - Up

    A loose quick disconnect may also stop cylinder movement. NOTE Use only Hawk approved quick disconnects. Part Numbers Part Name Part # Male Quick Disconnect (HC, RR)

  • Page 14: Winch Hook - Up

    Tightly connect the quick disconnects. A loose connection causes a pressure drop in the hydraulic fluid which heats up the fluid and reduces component life. NOTE Use only Hawk approved quick disconnects. Part Numbers Part Name Part # Male Quick Disconnect (P)
  • Page 15 Winch Hook - Up 7. Center the Suspension Ring (SR) on the Lateral tilt screw (LTS). 8. Use Raise (R) to raise the HawkJaw 1'- 2' ft. off the rig floor. 9. Use the Control Handles (CH) on both Control Panels and Raise (R) and Lower (L) to position the HawkJaw middle wrench (MW) near the drill pipe...
  • Page 16 Winch Hook - Up 10. Disengage the Winch Clutch (C). Spool out enough line to anchor the Winch Cable Spring Shackle (S) to a structural point on the derrick. 11. Anchor the Winch Cable Spring Shackle (S) to a structural point on the derrick.

  • Page 17: Operation

    Tightly connect the quick disconnects. A loose connection causes a pressure drop in the hydraulic fluid which heats up the fluid and reduces component life. NOTE Use only Hawk approved quick disconnects. Part Numbers Part Name Part # Male Quick Disconnect (P)

  • Page 18: Adjust For Make Up

    Adjust for Make Up Adjusting the Wrenches 1. Measure the tool joint with OD calipers. 2. Use the 1 1/4" wrench to adjust the Pointer (P) on the Pipe stop index (PI) to the OD tool joint size. Its always better to adjust the pointer 1/4"...

  • Page 19: Adjusting The Spinner

    Adjust for Make Up Adjusting the Spinner 1. Measure the drill pipe tube with OD calipers. 2. Remove the quick release pins (QR). 3. Slide the whole Drive unit (D) forward or backward to the appropriate holes. Use the pipe size index (I) to adjust the drive unit to the correct setting.

  • Page 20: Position For Make Up

    Position for Make Up 1. Stab the drill stand. 2. Center the Suspension Ring (SR) on the Lateral tilt screw (LTS). 3. Push and hold down Winch On (WOn) to move the HawkJaw onto the drill pipe connection. 4. Use Raise (R) and Lower (L) to center the Top wrench dies (TD) and the Middle wrench dies (MD) between the shoulder (S).
  • Page 21 Position for Make Up (cont.) 7. Check that the HawkJaw Top wrench (TW), Middle wrench (MW) and Bottom wrench (BW) hang straight and level when the drill pipe is against the pipe stop. 8. If the HawkJaw wrenches (TW, MW, BW) hang tilted forward or backward, use the Top Tilt (TT) button or the Bottom Tilt (BT) button to level...

  • Page 22: Setting Make Up Torque

    Setting Make Up Torque 1. Follow the steps on pages 17-21. 2. Turn the Selector Switch (SS) to Make. 3. Use the Red needle adjust (RNA) to rotate the Torque gauge red needle (RN) to the desired torque. 4. Rotate the Torque Set knob (K) counter- clockwise as far as the Torque Set knob (K) will turn.

  • Page 23: Make Up

    Make Up 1. Press in the Grip Hold (GH) button. 2. Press and hold Spin (S) until the stand rotates down to the shoulder. 3. Release Spin (S). 4. Push in and hold the wrench Grip (G). 5. Push and hold down Torque (T). 6.

  • Page 24: Low Torque Warning Test

    Grip (G). Wait for the Torque cylinder to reset. LOW TORQUE WARNING SYS- TEM CHECK Test#1: Hawk strongly recom- mends testing the Low Torque Warning System on every trip. If this test procedure is not performed, the drill string could be over torqued.

  • Page 25: Adjust For Break Out

    Adjust for Break Out Adjusting the Wrenches 1. Measure the tool joint with OD calipers. 2. Use the 1 1/4" wrench to adjust the Pointer (P) on the Pipe stop index (PI) to the OD tool joint size. Its always better to adjust the pointer 1/4"...

  • Page 26: Adjusting The Spinner

    Adjust for Break Out Adjusting the Spinner 1. Measure the drill pipe tube with OD calipers. 2. Remove the quick release pins (QR). 3. Slide the whole Drive unit (D) forward or backward to the appropriate holes. Use the pipe size index (I) to adjust the drive unit to the correct setting.

  • Page 27: Position For Break Out

    Position for Break Out 1. Center the Suspension Ring (SR) on the Lateral tilt screw (LTS). 2. Push and hold down Winch On (WOn) to move the HawkJaw onto the drill pipe connection. 3. Use Raise (R) and Lower (L) to center the Middle wrench dies (MD) and the Bottom wrench dies (BD) between the shoulder (S).
  • Page 28 Position for Break Out 6. Check that the HawkJaw Top wrench (TW), Middle wrench (MW) and Bottom wrench (BW) hang straight and level when the drill pipe is against the pipe stop. 7. If the HawkJaw wrenches (TW, MW, BW) hang tilted forward or backward, use the Top Tilt (TT) button or the Bottom Tilt (BT) button to level the wrenches.

  • Page 29: Break Out

    Break Out 1. Rotate the Selector Switch (SS) clockwise to the break position. 2. Push in the Grip Hold (GH) button. 3. Push and hold in the wrench Grip (G). 4. Push and hold down Torque (T). 5. When break out occurs, release Torque (T).

  • Page 30: Maintenance & Repair

    Wrench Maintenance Grease Once per Trip Tools Required Grease gun Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3. Press the Grip button repeatedly to bleed hydraulic pressure.

  • Page 31: Wrench Hook

    Wrench Maintenance Grease Once per Week, Minimum Wrench Hook 1. Surface grease the hook thread (T) on the top wrench, middle wrench, and bottom wrench. 2. Rotate the wrench nut (N) on the top wrench, middle wrench, and bottom wrench to spread grease on the full thread area.

  • Page 32: Grip Cylinder Pivot Points

    Wrench Maintenance Grease Once per Week, Minimum Tools Required Grease gun Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3. Press the Grip button repeatedly to bleed hydraulic pressure.

  • Page 33: Mounting Arm Pivot Points

    Wrench Maintenance Grease Once per Week, Minimum Tools Required Grease gun Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3. Press the Grip button repeatedly to bleed hydraulic pressure.

  • Page 34: Filter Maintenance

    1. Depress the Red button (RB) WARNING located under the See-through Running the HawkJaw rubber weather cap (SC). without a Hawk approved 2. Operate the HawkJaw. pressure-side filter element 3. If the Red button pops up, (Part # 061-H25A) voids proceed with Step 4.

  • Page 35: Air Filters

    Base (C) 061-A22E Corner Bolt Kit (CB) 061-J29F Corner Bolt Kit (CB) 061-A22F Base Core (H) 061-A22G WARNING Running the HawkJaw without Hawk approved air filters (Part # 061-J29, 061-A22) voids the warranty and shortens component life. Maintenance & Repair...

  • Page 36: Changing The Hook Dies

    Changing the Hook Dies Tools Required 3/4" wrench, See Drawings. Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3. Press the Grip button repeatedly to bleed hydraulic pressure.

  • Page 37: Changing The Heel Dies

    Changing the Heel Dies Tools Required 3/4" wrench, See Drawings. Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3. Press the Grip button repeatedly to bleed hydraulic pressure.
  • Page 38 Changing the Heel Dies 7. Make sure the back and sides of the new Die are clean. 8. Grease the back of the new Die. 9. Insert the new Die into the Die Holder (DH) with the teeth of the Die facing out. 10.

  • Page 39: Middle Wrench Heel Die

    Changing the Heel Dies Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3. Press the Grip button repeatedly to bleed hydraulic pressure.
  • Page 40 Changing the Heel Dies 8. Replace the Top Die Retainer (DR). 9. Insert the Heel Die Pin (P). 10. Use the 3/4" wrench to replace the Heel Die Roller Bolt (B) and Lock Washers. Part Numbers Part Name Part # Spirol Lock Washer 999-810703 Die Roller Bolt (B)

  • Page 41: Bottom Wrench Heel Die

    Changing the Heel Dies Tools Required 3/4" wrench, See Drawings. Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3. Press the Grip button repeatedly to bleed hydraulic pressure.
  • Page 42 Changing the Heel Dies 6. Grease the back of the new Die. 7. Insert the new Die into the Die Holder (DH) with the teeth of the Die facing out. 8. Replace the Top Die Retainer (DR). 9. Insert the Heel Die Pin (P). 10.

  • Page 43: Spinner Maintenance

    Spinner Maintenance Notice Spinner chain lubrication must be done during normal operation of the Hawkjaw. Do not run the spinner when the Hawkjaw is not on the pipe. Initial Steps 1. Position the Hawkjaw for breakout. Chain Lubrication 1. Pull the Hawkjaw onto the pipe. 2.

  • Page 44: Drive Roller Sprocket Bearings

    Spinner Maintenance Grease Once per Month Tools Required Grease gun, 7/16" wrench Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3.

  • Page 45: Chain Drive Shaft Bearing

    Spinner Maintenance Grease Once per Month Tools Required Grease gun Spinner Grip Cylinders 1. Pump grease fittings SC1-SC4. Chain Drive Shaft Bearing 1. Pump grease fitting CB1. Maintenance & Repair...

  • Page 46: Spinner Mount Sliding Block

    Spinner Maintenance Grease Once per Month Tools Required Grease gun Spinner Mount Sliding Tube 1. Pump grease fittings ST1-ST4. Spinner Mount Sliding Block 1. Pump grease fittings SB1. NOTE Consistent lubrication of the Spinner sliding tube and block increases performance and component life. Maintenance &...

  • Page 47: Reducer Gear Box

    Spinner Maintenance Check Oil Level Once per Month Lubricant Required 85-90 weight gear oil SAE #AGMA5 Reducer Gear Box 1. Make sure the gear box oil level reaches the top pipe plug (RP). Winch Gear Box 1. Make sure the gear box oil level reaches the top pipe plug (WP).

  • Page 48: Changing The Spinner Chain

    Changing the Spinner Chain Tools Required 7/8" wrench, 7/16" wrench, Hammer, Needle-Nose Pliers Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit.
  • Page 49 Changing the Spinner Chain 6. From the front of the unit, use the Needle-nose pliers to remove the Cotter pins (CP) in one of the Chain links. 7. Use the hammer to remove the Chain link pin (CLP). 8. Pull out the old chain. Make sure the chain does not catch on the Drive Sprocket (DS).

  • Page 50: Changing The Drive Rollers

    Changing the Drive Rollers Tools Required 3/4" wrench Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3. Press the Grip button repeatedly to bleed hydraulic pressure.
  • Page 51 Changing the Drive Rollers 2. Use the 3/4" wrench to remove all Bearing Cap Bolts (9). 3. Remove the Bearing Caps (2) and Bearing Seals (3). 4. Slide out the Drive Roller Sprockets (4). 5. Remove the Drive Roller Snap Rings (7).

  • Page 52: Changing The Drive Roller Sprocket Bearings

    Changing the Drive Roller Sprocket Bearings Tools Required Four 1/4"-20 x 1 1/2" Hex Tap SS (Part # 999-805867), 7/16" wrench, 3/4" wrench Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2.
  • Page 53 Lock Washers (12) as shown. Torque Bearing Cap Bolts (9) to 75 lb. ft. NOTE Hawk recommends that all four bearings (8) be replaced each time a bearing (8) is changed. Always use new lock washers (12) when replacing bearing cap bolts (9).

  • Page 54: Changing The Torque Cylinder

    Changing the Torque Cylinder Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. Torque Cylinder 1. Press Grip Hold (GH). 2. Press and hold Grip (G) 3. While holding down Grip (G), press and hold down Torque (T) until the Torque Cylinder Rod Pin (P) extends out from...
  • Page 55 Changing the Torque Cylinder 6. Use the 1 1/8" wrench to slowly loosen the Cap side Hoses (CH1), (CH2). Check for fluid flow. Bleed any pressure. Disconnect the Cap side Hoses (CH1), (CH2). 7. Use the 1" wrench to slowly loosen the Rod side Hose (RH).
  • Page 56 Changing the Torque Cylinder 15. Use air pressure or manual force to extend the new Torque Cylinder Rod to the length of the old Torque Cylinder Rod. 16. Place the Bottom Trunion Mount Plate (BMP) and Top Trunion Mount Plate (TMP) on the new Torque Cylinder.
  • Page 57 Changing the Torque Cylinder 21. Use the 1" and 1 1/8" wrench to connect the Rod side Hose (RH) and the Cap side Hoses (CH1), (CH2). 22. Insert the Torque Cylinder Rod Pin (P). 23. Insert the Torque Cylinder Safety Clip (SC). 24.

  • Page 58: Changing The Grip Cylinders

    Changing the Grip Cylinders Tools Required Two 11/16" wrenches, Two 1 1/2" wrenches Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit.
  • Page 59 Changing the Grip Cylinders CB RH 3. Use the Two 1 1/2" wrenches to remove the Grip Cylinder Cap side Bolt (CB) and Flex Lock Nut. 4. Use the 1 1/2" wrench to remove the Grip Cylinder Rod side Pin (RP).

  • Page 60: Middle Grip Cylinder

    Changing the Grip Cylinders Tools Required Two 11/16" wrenches, Two 1 1/2" wrenches Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Follow Steps 1-4 on p. 52. Middle Grip Cylinder 1.
  • Page 61 Changing the Grip Cylinders 6. Place the new Grip Cylinder into the Cap side Eye (CE) and Rod side Eye (RE). 7. Use the Two 1 1/2" wrenches to replace the Grip Cylinder Cap side Bolt (CB). 8. Replace the Grip Cylinder Rod side Bolt (RB).

  • Page 62: Bottom Grip Cylinder

    Changing the Grip Cylinders Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3. Press the Grip button repeatedly to bleed hydraulic pressure.
  • Page 63 Changing the Grip Cylinders 3. Use the Two 1 1/2" wrenches to remove the Grip Cylinder Cap side Bolt (CB) and Flex Lock Nut. 4. Use the 1 1/2" wrench to remove the Grip Cylinder Rod side Bolt (RB). 5. Slide out the Grip Cylinder (C). 6.

  • Page 64: Main Hydraulic Block Fitting And Hose Access

    Main Hydraulic Block Fitting and Hose Access Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Use Raise (R) to raise the HawkJaw 6"-12" inches off the derrick floor.

  • Page 65: Air Logic System And Main Block

    Main Hydraulic Block Fitting and Hose Access Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Use Raise (R) to raise the HawkJaw 3"-5" inches off the derrick floor.

  • Page 66: Spinner Motor Sequence Valve Access

    Spinner Motor Sequence Valve Access Tools Required 3/4" wrench, 3/16" Allen wrench Initial Steps 1. Make sure the HawkJaw is off the drill pipe connection and in the rest position on the derrick. 2. Shut down the Hydraulic power unit. 3.

  • Page 67: Trouble Shooting

    Trouble Shooting Problem Remedy Hose leaks. Replace the hose. See Drawings. All Grip cylinders extend, and the Torque The Pressure and Tank lines are switched. Properly cylinder extends. connect the Pressure and Tank lines. See Operation. One or more Grip cylinders extend. Make sure the hydraulic power unit is shut down.
  • Page 68 Trouble Shooting Problem Remedy Spinner pops off the drill pipe tube when the The spinner is adjusted too small for the drill pipe spinner rotates the pipe. tube. Adjust the spinner to the correct pipe size. See Operation. Spinner Drive Rollers touch when the spinner Adjust the spinner to the next smaller pipe size.
  • Page 69 Trouble Shooting Problem Remedy Spinner motor sequence valve is located at Port Spinner begins to spin before the spinner doors close on the drill pipe tube. (Cont.) MSEQ on the main hydraulic block. See Mainte- nance & Repair, Drawings. Use an allen wrench to rotate the Spinner motor Spinner moves forward and the doors close sequence valve adjustment counter-clockwise until on the pipe, but the spinner does not spin.
  • Page 70 Replace the Drive Roller The Drive motor is worn out. With filtered hy- Sprocket Bearings. See Maintenance & draulic fluid through a Hawk approved filter, the Repair. Drive motor is a long term wear item. If all other rotating members on the spinner work, inspect the rotating group, bearings and seals for wear.
  • Page 71 Trouble Shooting Problem Remedy HawkJaw performance and speed not to see that they are securely tightened. A bad quick up to par. disconnect can cause the Hawkjaw to mal-function. Replace the faulty connector. The air pressure is low. Increase the air pressure to the HawkJaw.
  • Page 72 Trouble Shooting Problem Remedy HawkJaw performance and speed not up to There is a leak in the hydraulic system. Make sure par. the air supply hose to the HawkJaw is discon- nected. Make sure the hydraulic power unit is on. Check for Torque cylinder piston seal integrity.
  • Page 73 Trouble Shooting Problem Remedy Hydraulic fluid heats up. There is a leak in the hydraulic system. See Trouble Shooting. The Raise/Lower Cylinder moves slower than Check to make sure the hydraulic power unit is usual, or the HawkJaw sinks while it hangs. producing 2500 psi at 20-35 gpm.
  • Page 74 Trouble Shooting Problem Remedy Push in the "E" stop button. Access the main The Raise/Lower Cylinder moves at an undesired speed hydraulic block. See Maintenance & Repair & Drawings. Use a 7/32" allen wrench to adjust the VR/ L sandwich valve H6 flow settings at each end. Rotate clockwise to reduce speed and counter- clockwise to increase speed of the Raise/Lower cylinder.
  • Page 75 The low torque warning small "U" cup seal is leaking. Replace the seal. Make sure the seal is has failed. installed with the top of the "U" facing in. Order Hawk # 061-LTW-RK. See Drawings. Refer to LOW TORQUE WARNING TEST #2 PROCE- DURES. Troubleshooting...
  • Page 76 The low torque warning small "U" cup seal is leaking. Replace the seal. Make sure the seal is has failed. installed with the top of the "U" facing in. Order Hawk # 061-LTW-RK. See Drawings. Refer to LOW TORQUE WARNING TEST #2 PROCE- DURES. Troubleshooting...
  • Page 77 Notes Troubleshooting...

  • Page 78: Drawings

    100K-2GSR Full Hawkjaw Assembly 78 Drawings...
  • Page 79 100K-2GSR Full Hawkjaw Assembly ITEM QTY. PART NO./DESCRIPTION COMMENTS 100K-2GSR-12 Top-Bottom W rench Assembly See Explosion 100K-2GSR-9 Middle W rench Assembly See Explosion 100K-2GSR-5 Hydro-Pheumatic Assembly See Explosion 100K-2GSR-4 Hanger Assembly See Explosion 100K-2GSR-6 Left Control Handle Assembly See Explosion 100K-2GSR-7 Right Control Handle Assembly See Explosion 100K-2GSR-13 W inch Mount Assembly...

  • Page 80: 2Gjr Top-Bottom Wrench Assembly

    100K-2GSR Top-Bottom Wrench Assembly 80 Drawings...
  • Page 81 100K-2GSR Top-Bottom Wrench Assembly ITEM QTY. PART NO./DESCRIPTION COMMENTS 20145 B ase P late As sembly 20084 Torque Cylinder Bracket, Upper Ass embly 20088 Torque Cylinder Bracket, Lower 20080-2 Torque Cylinder Mount, Lower A ssembly 20004-3A Jaw Plate Assembly, W elded 20004-1B Jaw Plate Assembly, W elded 12042 S him 20002A Hook Assembly...

  • Page 82: 2Gjr Midde Wrench Assembly

    100K-2GSR Midde Wrench Assembly 82 Drawings...
  • Page 83 100K-2GSR Middle Wrench Assembly ITEM QTY. PART NO./DESCRIPTION COMMENTS 20008 Base Plate, Moving Assembly, W elded 20016A Linkage, Split Assembly 20028-245 Pin, Linkage Mount Assembly 20028-245B Pin, Linkage Mount Assembly 146 Thrust Bearing Assembly 20024 Linkage Assembly 20029-138AM W asher Assembly 20024-1 Stepped Linkage Arm Assembly 20002A Hook Assembly 20072 Nut Bearing Plate...

  • Page 84: 2Gjr Hydro-Pneumatic Assembly

    100K-2GSR Hydro-Pneumatic Assembly 84 Drawings...
  • Page 85 100K-2GSR Hydro-Pneumatic Assembly ITEM QTY. PART NO./DESCRIPTION COMMENTS 100K-2GSR Hydraulic Connections (J1A-A) See Explosion 20169 Control Housing Assembly 20176A Block Plate Assembly 20167-2 Inspection Cover 20167-3A Inspection Cover 20162A Control Housing Assembly 806244_1.2-13 x 1.0 Hex Bolt 810703_1.2 Lock W asher 810705_1.2 Flat W asher 806239_1.2-13 x .75lg.

  • Page 86: 2Gjr Hangerassembly

    100K-2GSR HangerAssembly 86 Drawings...
  • Page 87 100K-2GSR HangerAssembly ITEM Q TY. PART NO ./DESCRIPTIO N COMMENTS 20147 Hanger Assembly 20151 Spindle Bloc k 20267 Hose Mount, 2GSR Assembly 20059 U Bolt for 2GSR H18S Grip Tilt Cy linder Assembly See Explosion SH30540PP 1.4 Hose Clamp (pipe) SH5150PP 1_1.2 Hosec lamp (tube) SH61900PP H30540-1 Brac ket, Hose Clamp...

  • Page 88: 2Gjr Left Control Handle Assembly

    100K-2GSR Left Control Handle Assembly 88 Drawings...
  • Page 89 100K-2GSR Left Control Handle Assembly IT E M Q T Y. P A R T N O ./D E S C R IP T IO N C O M M E N T S 7 0 1 0 0 L e ft C o n tr o l H a n d le A s s e m b ly 7 0 1 0 3 L e ft C o n tr o l P a n e l A ss e m b ly A 1 5 A ir M a n ifo ld 2 0 1 0 4 - 1 C o n tr o l Ha n d le , To p &...

  • Page 90: 2Gjr Right Control Handle Assembly

    100K-2GSR Right Control Handle Assembly 90 Drawings...
  • Page 91 100K-2GSR Right Control Handle Assembly ITEM Q TY. PAR T N O ./D ESC R IPTIO N C O MMEN TS 70101 Right C ontrol Handle Assembly 70105 Right C ontrol Panel Assembly 805916_5.16-18 x .50 LG. HEX BOLT 810616_5.16 Loc k W asher 806004_3.8-16 x .75 Lg.

  • Page 92: 2Gjr Winch Mountassembly

    100K-2GSR Winch MountAssembly 92 Drawings...
  • Page 93 100K-2GSR Winch MountAssembly ITEM Q TY. P AR T N O ./D ESC R IPTIO N C O MMEN TS 20223 W inc h Mount Assembly H59 W inc h Assembly , Manual 59R Roller Assembly , W inc h 20286 W inc h C over 20203 Spac er, W inc h 806542-1_3.4-16 x 4.50 Hex Bolt...

  • Page 94: 2Gjr Spinner Mountassembly

    100K-2GSR Spinner MountAssembly 94 Drawings...
  • Page 95 100K-2GSR Spinner MountAssembly ITEM QTY. PART NO./DESCRIPTION COMMENTS 20094A Spinner Mount Assembly HA-032596A Spring 20118 Slide Tube Assembly 20126 Slide Base 20127 Side Slide 20131 Slide Cap 20129 Slide Block 20134 Pivot Pin 20125 Return Bumper 20133 Cylinder Bolt 20135 Cylinder Mount, Rubber 4 Thrust Bearing Assembly PRP568-231 O Ring 9108A041 W asher...

  • Page 96: 2Gjr Stand Assembly

    100K-2GSR Stand Assembly 96 Drawings...
  • Page 97 100K-2GSR Stand Assembly ITEM QTY. PAR T NO ./DESC RIPTIO N CO MMENTS 20075A Stand Assembly 806542-1_3.4-16 x 4.50 Hex Bolt 91074A036 Loc k W asher Assembly , 3.4 806436_5.8-11 x 1.50 lg. Hex Bolt Grd. 9 810732_5.8 Loc k W asher 806439_5.8-11 x 2.50 lg Hex Bolt Grd.

  • Page 98: 2Gjr Hawkjaw Spinner Assembly

    100K-2GSR Hawkjaw Spinner Assembly 98 Drawings...
  • Page 99 100K-2GSR Hawkjaw Spinner Assembly ITEM QTY. PART NO./DESCRIPTION COMMENTS 25710-SR Case Assembly, Stationary 95601A435 Fiber W asher 25703-SR Case Assembly, Moving Arm 24625 Reducer Assembly See Explosion 24701 Mounting Plate, Gear Box 24646 W ear Block 24642 Key, Drive Sprocket 24641 Drive Sprocket 24635 Spacer, Drive Sprocket 24656 Drive Shaft Bearing, Modified...

  • Page 100: 2Gjr Pipe Stop Assembly

    100K-2GSR Pipe Stop Assembly 100 Drawings...
  • Page 101 100K-2GSR Pipe Stop Assembly ITEM QTY. PART NO./DESCRIPTION COMMENTS 20066 Pointer 20060 Adjust Clevis 20050 Linkage, Stop Assembly 809403_10-32x.375 Screw SS 20041A Pipe Stop Rubber 20029-250 W asher, Pipe Stop 20214-3 Hex Bolt 806414-500_5.8-11 Flex Nut (31FA1011) 809476_10 Lock W asher, High Collar 20229 Linkage Nut, Modified 20061A Shock Sleeve 20069 Index, Pipe Stop...

  • Page 102: 2Gjr Hydraulic Connections

    100K-2GSR Hydraulic Connections 102 Drawings...
  • Page 103 100K-2GSR Hydraulic Connections ITEM QTY. PART NO./DESC PORT/DESC. HOSE DESTINATION 100K-2GSR Main Manifold Assembly (J1A-A) HOS-12_-10FJICx-10FJICx35.00lg. Hose Torque Cyl. Rod HOS-132G_-10FJICx-10FJICx 110.0lg-10. Hose PR2-Torque Cntrl. Manifold HOS-82G_-8FJICx-8FJICx100.00lg. Hose WIN, WOUT Winch Motor HOS-42G_1.4MNPTx-4FJICx117.00lg. Hose R, L Raise/Lower Cyl. Rod, Pist. HOS-102G_-10FJICx-10FJICx115.00lg.

  • Page 104: 2Gjr Spin Manifold Assembly

    100K-2GSR Spin Manifold Assembly 104 Drawings...
  • Page 105 100K-2GSR Spin Manifold Assembly ITEM QTY. PART NO./DESC PORT/DESC. HOSE DESTINATION H38 Spin Manifold H35 Sequence Valve H34 Check Valve H31 Flow Control Valve H33 Check Valve V3,V8 H36 Pressure Reducing Valve H45 Needle Check Valve 2062-8-8S_8MORB x 8MJIC Fitting 90 206209-6-6S_8MORB x 8MJIC Fitting 90 Ext.

  • Page 106: 2Gjr Raise/Lower Cylinder Assembly

    100K-2GSR Raise/Lower Cylinder Assembly 106 Drawings...
  • Page 107 100K-2GSR Raise/Lower Cylinder Assembly ITEM QTY. PART NO ./DESCRIPTIO N COMMENTS 2572-9 Barrel, Raise Lower Cy linder 2572-6 Rod, Raise Lower Cy linder 2572-8 Rod Clevis, Raise Lower Cy linder 2572-7 Seal Retainer, Raise Lower Cy l. TPO-28 Piston Seal TPO-28 Bac kup, Piston Seal 940-15 Rod W iper, Raise Lower Cy l.

  • Page 108: 2Gjr Main Manifold Assembly

    100K-2GSR Main Manifold Assembly 108 Drawings...
  • Page 109 100K-2GSR Main Manifold Assembly ITEM QTY. PART NO./DESCRIPTION COMMENTS J1A-A Main Manifold V6APBCP_DO5_Assembly V6ABT_DO5_Assembly H7 Pilot Check Sandwich Assembly H6 Flow Control Sandwich Assembly H53S Directional Valve Assembly H93S Directional Valve Assembly H6P Pressure Control Sandwich H4B Air Piloted 2-W ay Valve V6SR_DO5_Assembly H9JR 3Grip Valve H5 Directional Valve Assembly...

  • Page 110: 2Gjr Main Manifold Air Connections

    100K-2GSR Main Manifold Air Connections 110 Drawings...
  • Page 111 100K-2GSR Main Manifold Air Connections LEFT CONNECTOR DUPLICATE PORT DESCRIPTION COLOR SIZE AIR SUPPLY BLACK 3/16 AIR SUPPLY TORQUE YELLOW 5/32 AIR SUPPLY SPIN CLEAR 5/32 AIR SUPPLY W INCH 5/32 GRIP #1 YELLOW 5/32 GRIP #2 ORANGE 5/32 GRIP #3 BLUE 5/32 RAISE VALVE SIDE "b"...

  • Page 112: 2Gjr Left Control Handle Air Connections

    100K-2GSR Left Control Handle Air Connections 112 Drawings...
  • Page 113 100K-2GSR Left Control Handle Air Connections ITEM NO. QTY.THIS ASSY. PART NO./ DESCRIPTION COMMENTS A15 Air Manifold A40-5 Red Air Hose A36 Port Plug A1 Selector Switch Assembly A8GH Grip Hold Button Assy A3 Button Air Valve Assembly A4G Grip Valve Assembly 2081-4-2S 1.4 x 1.8 H.P.

  • Page 114: 2Gjr Right Control Handle Air Connections

    100K-2GSR Right Control Handle Air Connections 114 Drawings...
  • Page 115 100K-2GSR Right Control Handle Air Connections IT E M Q T Y . P A R T N O . / D E S C R IP T IO N C O M M E N T S A 1 5 A i r M a n if o ld A 4 0 - 1 Y e llo w A i r H o s e A 4 0 - 2 O r a n g e A i r H o s e A 4 0 - 8 G r a y A ir H o s e...

  • Page 116: 2Gjr Torque Cylinder Assembly

    100K-2GSR Torque Cylinder Assembly 116 Drawings...
  • Page 117 20087 Retainer Ring, H17 Torque Cylinder 2047-2-2S 2MNPTX2FNPT Fitting 90 Drg Swivel * These parts are kitted Hawk P/N J20-RK ** These parts are kitted Hawk P/N/ LTW -RK *** These parts are available in set only as P/N LTW -P/S Drawings 117...

  • Page 118: 2Gjr Left Control Tube Assy Air Conn

    100K-2GSR Left Control Tube Assy Air Conn 118 Drawings...
  • Page 119 100K-2GSR Left Control Tube Assy Air Conn ITEM NO . Q TY.THIS ASSY PART NO ./DESCRIPTIO N CO MMENTS A11-1LCH Multiplex Connec tor Assembly See Explos. Drw. A11-LCH Multiplex Connec tor Assembly See Explos. Drw. A11LFT Left Control Tube Assembly Drawings 119...

  • Page 120: 2Gjr Right Control Tube Assy Air Conn

    100K-2GSR Right Control Tube Assy Air Conn 120 Drawings...
  • Page 121 100K-2GSR Right Control Tube Assy Air Conn ITEM Q TY. PART NO ./DESCRIPTIO N CO MMENTS A11-RT_Right Control Tube Assembly See Explosion A11-RCH Multiplex Connec tor Assembly See Explosion A11-2RCH Multiplex Connec tor Assembly Drawings 121...

  • Page 122: 25726 Chain Oiler Assembly

    25726 Chain Oiler Assembly 122 Drawings...
  • Page 123 25726 Chain Oiler Assembly ITEM NO. QTY.THIS ASSY PART NO./ DESCRIPTION COMMENTS 2083-4-45 1-4 NPT ADAPTER 11432-SSP Body, SST, Polished 8536-200 STRAINER, SST 7894-NY TIP GASKET, NYLON 7894-NY TIP GASKET, NYLON TP400025-TC .013 Nozzle 7890-SSP CAP,SST, POLISHED 805916_5.16-18 x .50 LG. HEX BOLT 2049-2-2 1-8,45 Drg Adapter 810616_5.16 Lock W asher 25726 Chain Oiler W eldment...

  • Page 124: 20209-Bot Heel Die Holder Assembly, Bottom

    20209-BOT Heel Die Holder Assembly, Bottom 124 Drawings...
  • Page 125 20209-BOT Heel Die Holder Assembly, Bottom ITE M Q TY. P AR T N O ./D E S C R IP TIO N C O MME N TS 20192-1B D ie Holder, Heel S ide 810703_1.2 Loc k W asher 20194 D ie 20212-1A Retainer, Heel D ie 20208-870 S pac er, D ie Holder...

  • Page 126: 20209-Mid Heel Die Holder Assembly, Middle

    20209-MID Heel Die Holder Assembly, Middle 126 Drawings...
  • Page 127 20209-MID Heel Die Holder Assembly, Middle IT E M Q T Y. P AR T N O ./D E S C R IP T IO N C O M M E N T S 2019 2- 1B D ie Holder , Heel S ide 2021 0 Roller A ssem bly 2020 8A S p ac er B ushing, Roller 8062 76_1.2- 13 x 1.7 5 Hex B olt...

  • Page 128: 20209-Top Heel Die Holder Assembly, Top

    20209-TOP Heel Die Holder Assembly, Top 128 Drawings...
  • Page 129 20209-TOP Heel Die Holder Assembly, Top IT E M N O . Q TY.TH IS AS S Y P AR T N O ./ D E S C R IP T IO N C O M ME N T S 20192-1B D ie Holder , Heel S ide 20210 Roller A ssembly 20208A S pac er B ushing, Roller...

  • Page 130: 20211-Mid Hook Die Holder Assembly, Middle

    20211-MID Hook Die Holder Assembly, Middle 130 Drawings...
  • Page 131 20211-MID Hook Die Holder Assembly, Middle ITE M Q TY. P AR T N O ./D E S C R IP TIO N C O MME N TS 20192B D ie Holder, Hook S ide 20194 D ie 806246_1.2-13 x 1.00 Hex B olt Grd. 9 1103K 2 Grease Fitting, 45 D egree 810703_1.2 Loc k W asher 20212A D ie Retainer, Upper Hook...

  • Page 132: 20211-Tb Hook Die Holder Assembly, Middle

    20211-TB Hook Die Holder Assembly, Middle 132 Drawings...
  • Page 133 20211-TB Hook Die Holder Assembly, Middle ITEM NO. QTY./THIS ASSY PART NO./ DESCRIPTION COMMENTS 20192B Die Holder, Hook Side 1103K2 Grease Fitting, 45 Degree 20212A Die Retainer, Upper Hook 20213 Die Retainer, Bottom 806246_1.2-13 x 1.00 Hex Bolt Grd. 9 810703_1.2 Loc k W asher 20194 Die Drawings 133...

  • Page 134: Cyl25-As Top, -Bs Bottom Spinner Grip Cyl

    CYL25-AS Top, -BS Bottom Spinner Grip Cyl 134 Drawings...
  • Page 135 CYL25-AS Top, -BS Bottom Spinner Grip Cyl ITE M N O . Q TY.TH IS AS S Y P AR T N O ./D E S C R IP TIO N C O MME N TS 2560-A S .B S B arrel, S pinner Grip A S -Top/B S -B ott.

  • Page 136: 59R Roller Assembly, Winch

    59R Roller Assembly, Winch 136 Drawings...
  • Page 137 59R Roller Assembly, Winch IT E M Q T Y. P AR T N O ./D E S C R IP T IO N C O M M E N T S H59R- 1 Ro lle r B ody H59R- 2B Roller , Long w B ushin g H59R- 2A Roller , S ho r t w B ushing H59R- 1B Z A xle S ha ft, L ong H59R- 1A Z A xle S ha ft, S hor t...

  • Page 138: A11-1Lch Multiplex Connector Assembly

    A11-1LCH Multiplex Connector Assembly 138 Drawings...
  • Page 139 A11-1LCH Multiplex Connector Assembly ITEM N O . Q TY./THIS ASSY PAR T NO ./ DESCR IPTIO N C O MMENTS 70033 Male C oupler 807512_3.16 x .50lg. Roll Pin 90130A029 Rubber W asher Seal 70031 Panel Nut 70051 Female Coupler 70044 Swivel Nut US-206-S Retainer Ring A27 5.32 x 1.8 PTC Str.

  • Page 140: A11-2Rch Multiplex Connector Assembly

    A11-2RCH Multiplex Connector Assembly 140 Drawings...
  • Page 141 A11-2RCH Multiplex Connector Assembly ITEM N O . Q TY.TH IS ASSY PAR T N O ./ D ESC R IPTIO N C O MMEN TS 70033 Male C oupler 807512_3.16 x .50lg. Roll Pin 90130A029 Rubber W asher Seal 70031 Panel Nut 70051 Female C oupler 70044 Swivel Nut...

  • Page 142: A11-Lch Multiplex Connector

    A11-LCH Multiplex Connector 142 Drawings...
  • Page 143 A11-LCH Multiplex Connector ITE M N O . Q TY./TH IS AS S Y. P AR T N O ./ D E S C R IPTIO N C O MME N TS 70033 Male C oupler 807512_3.16 x .50lg. Roll P in 90130A029 Rubber W asher S eal 70031 P anel Nut 70051 Female C oupler...

  • Page 144: A11-Rch Multiplex Connector

    A11-RCH Multiplex Connector 144 Drawings...
  • Page 145 A11-RCH Multiplex Connector ITEM N O . Q TY.TH IS ASS Y. PAR T N O ./ D ESC R IPTIO N C O MMEN TS 70033 Male C oupler 807512_3.16 x .50lg. Roll Pin 90130A029 Rubber W asher Seal 70031 Panel Nut 70051 Female C oupler 70044 Swivel Nut...

  • Page 146: A22 On Board Air Filter Assembly

    A22 On Board Air Filter Assembly 146 Drawings...
  • Page 147 A22 On Board Air Filter Assembly ITEM QTY. PART NO./DESCRIPTION COMMENTS A22 Top Cover, Air Filter Not Spare part A22 Base Top, Air Filter Not Spare part A22H Base Core, Air Filter A22E Base, Air Filter A22D Gasket, Air Filter A22 Star Spacer, Air Filter Not Spare part A22B_C Filter Cartrige, Air Filter...

  • Page 148: H18S Grip Tilt Cylinder Assembly

    H18S Grip Tilt Cylinder Assembly 148 Drawings...
  • Page 149 H18S Grip Tilt Cylinder Assembly ITEM NO. QTY./THIS ASSY PART NO./ DESCRIPTION COMMENTS H18S-3 Barrel Assembly H18S-5 Seal Retainer H18S-6 Rod H18S-4 Piston H18S-RK-1 W ear Ring H18S-RK-3 Static Seal 1103K1 Grease Fitting, Straight H18S-RK-4 Seal Backup H18S-RK-5 Rod Seal H18S-RK-6 Rod W iper H18S-RK-2 Piston Seal H18S-RK-2A Backup, Piston Seal...

  • Page 150: H25 Hydraulic Filter Assembly

    H25 Hydraulic Filter Assembly 150 Drawings...
  • Page 151 H25 Hydraulic Filter Assembly ITEM QTY. PART NO./DESC PORT/DESC. HOSE DESTINATION Hydraulic Filter Body H25RC Indicator Fitting H25A Filter Element H25B Filter Canister 2062-16-12S_16MORB x 12MJIC Fitting 90 H52 Male Quick Disconnect HOS-1_1 MNPTx-12FJICx180.00lg_-16 Hose Pressure Line, Power Unit Right Port, Filter HOS-112G_3.4MNPTx-12FJICx41.00lg_-12 Hose Left Port, Filter Main Press.

  • Page 152: H37S-2 Push Cylinder Assembly

    H37S-2 Push Cylinder Assembly 152 Drawings...
  • Page 153 H37S-2 Push Cylinder Assembly IT E M Q T Y . P A R T N O . / D E S C R IP T IO N C O M M E N T S 2 0 0 6 - 1 0 B a r r e l 2 0 0 6 - 1 2 S e a l R e ta in e r 2 0 0 6 - 1 1 R o d 2 0 0 6 - 1 3 P is to n...

  • Page 154: 100K-2Gsr Hydraulic Pipe Clamp

    100K-2GSR Hydraulic Pipe Clamp 154 Drawings...
  • Page 155 100K-2GSR Hydraulic Pipe Clamp ITEM QTY. PART NO./DESCRIPTION DESTINATION COMMENTS 20045A-10 Mount Plate W ldmnt 20045A-15 Stepped Hook W ldmnt 146 Thrust Bearing Assembly 20208 Spacer Bushing, Roller 20210 Roller Assembly 20045A-6 Bolt, Roller Assy 1.5-13 x 2.75 20045A-2 Bushing 62205K29 Clevis,Rod 806542-1_3.4-16 x 4.50 Hex Bolt 1103K1 Grease Fitting, Straight...

  • Page 156: 100K-2Gsr H18 Top Grip Cylinder

    100K-2GSR H18 Top Grip Cylinder 156 Drawings...
  • Page 157 100K-2GSR H18 Top Grip Cylinder ITE M Q TY. P AR T N O ./D E S C R IP TIO N C O MME N TS 4E 550A Grip C y linder Tube 5A 223A Rod 74005 Rod Head 73384 P iston 32172 W ear Ring 10323 U C up Seal...

  • Page 158: 100K-2Gsr Torque Manifold

    100K-2GSR Torque Manifold 158 Drawings...
  • Page 159 100K-2GSR Torque Manifold ITEM QTY. PART NO./DESC PORT/DESC. HOSE DESTINATION 20222 Torque Control Block, Modification J55A Torque Control Valve Assembly CXGD-XBN Check Valve 900598-6S_MORB Plug 2062-12-10S_12MORB x 10MJIC Fitting 90 HOS-6A_-10FJICx-10FJICx87.00lg. Hose Piston-Torque Cyl. 2047-2-2S 2MNPTX2FNPT Fitting 90 Drg Swivel 30113 Orifice Fitting 2081-4-2S 1.4 x 1.8 H.P.

  • Page 160: 100K-2Gsr Gage Manifold

    100K-2GSR Gage Manifold 160 Drawings...
  • Page 161 100K-2GSR Gage Manifold ITEM QTY. PART NO./DESC. HOSE DESTINATION COMMENTS 20275 Gage Manifold 2047-2-2S 2MNPTX2FNPT Fitting 90 Drg Swivel 2084-2S-3.4 Nipple, Hydraulic Plated H40F Hydraulic Q.D. Socket HOS-32_1.8MNPTx1.8MNPTx17.00lg_1.8 Hose Gage H40M Hydraulic Q.D. Plug JHOS-OIL 1.8MNPTx1.8MNPTx83lg_1.8 Hose Top Port, Torque Cyl. Block 2082-2S_1.8 Pipe Plug HOS-18A_1.8MNPTx1.8MNPTx50lg_1.8 Hose GAGE Port, Torque Cntr.

  • Page 162: 100K-2Gsr Winch Assembly

    100K-2GSR Winch Assembly 162 Drawings...
  • Page 163 100K-2GSR Winch Assembly ITEM QTY. PART NO./DESCRIPTION COMMENTS 061-W 202-2-25 W orm Shaft 061-W 203-2-25 Bronze Gear 061-W 204 Drum 061-W 206 Gear Case Cover 061-W 207-K Yoke Kit 061-W 208 End Bearing 061-W 210-K Gear Case Cover Gasket Kit 061-W 213 Spring 061-W 214 Friction Block 061-W 216 Oil Seal...
  • Page 164 Notes 164 Drawings...

  • Page 165: Maintenance Schedule

    Maintenance Schedule HAWK INDUSTRIES, INC. HAWKJAW® RECOMMENDED MAINTENANCE CHECKLIST Hawkjaw S/N: Rig Name:______________________Maintenance Check Date: Pipe Size: A TICK SHOWN IN THE CLEAR CELLS, WILL INDICATE THE ITEM WAS FOUND TO BE ACCEPTABLE PLACE A TICK IN THE APPROPRIATE BOX ON THE RIGHT...

Table of Contents