John Lewis Sidewinder roman blind kit Quick Start Manual

Sidewinder roman blind kit
with cord guides
Please check the contents
headrail cam
headrail length (ready corded) support
60cm 1 2
90cm 1 3
120cm 1 3
150cm 1 4
180cm 1 5
Note: Cord pulleys on 60-120cm lengths operate at a ratio of 1:1, whilst 150 and 180cm operate on a ratio of 1:3.
1. Fabric requirements for your window size
1. A Measure the width and drop of your window for
recess fixed headrail or if you have mounted your
blind headrail outside the recess, measure the width
of the blind headrail by the drop required.
1. B Add to the finished blind the measurements shown
in diagram B.
On wider blinds more than a fabric width wide, join
the fabric so the blind will have seams an equal
distance from the centre. Mark the blind size plus
seams with tailors chalk. Trim out the size.
2. Sewing the side seams
Working on the back of the fabric, fold the side fabric
under 0.5cm ( 3 / 16 ") and then over 1cm ( 3 / 8 ") to
form a seam and sew down the inner edge.
Repeat for the opposite side.
3. Stitching the loop tape to the top of the blind
Remove loop tape from headrail.
3. A Fold over the top of the fabric 1cm ( 3 / 8 ").
3. B Place the loop tape over the fold leaving a
0.5cm ( 3 / 16 ") gap between the tape and the
top of the fold. Sew the tape into place with
two rows of stiches - a row on top and a
row on the bottom of the tape.
4. Sewing the bottom bar pocket
Fold over and create a 4cm (1 5 / 8 ") pocket with a
turn over of 1cm ( 3 / 8 ") as shown in the diagram.
Stitch along the top edge hem/pocket.
chain pulley end cap chain safety
guide
1 (ratio 1:1) 1 1
1 (ratio 1:1) 1 1
1 (ratio 1:1) 1 1
1 (ratio 1:3) 1 1
1 (ratio 1:3) 1 1
Thank you for purchasing this product. Please read the
instructions and warnings carefully before use to ensure
safe and satisfactory operation of this product. It is
recommended that this blind should only be installed
by persons competent in DIY.
roman bottom hook on
rods bar cord toggle
5 1 3
5 1 4
5 1 5
5 1 5
5 1 6
Recess fix
1 A
FINISHED
BLIND SIZE
B
( 3
1cm /
8 ")
TOP
Measure width
1.5cm
( 5
/
8 ")
5cm (2")
BOTTOM
( 3
1cm /
8 ")
2
( 3
0.5cm /
16 ")
A
3
( 3
1cm /
8 ")
4
( 3
1cm /
8 ")
5
4cm 1 /
( 8 ")
loop pocket roman headrail
tape blind tape trimming aid
0.62 Mtr 3.2 Mtr 1
0.92 Mtr 4.7 Mtr 1
1.22 Mtr 6.2 Mtr 1
1.52 Mtr 7.7 Mtr 1
1.82 Mtr 9.2 Mtr 1
Wall fix
headrail
finished
blind size
Width including
side seams
1.5cm
Drop including top
( 5
/
8 ")
tape seam and bottom
bar pocket seam
Fabric join
seam
1cm ( 3 /
8 ")
( 3
0.5cm /
16 ")
( 3
0.5cm /
16 ")
B
screws &
6
8
8
10
12
headrail
finished
blind size
Fabric join
seam