Download Print this page
John Lewis Corded roman blind kit Manual

John Lewis Corded roman blind kit Manual

With cord guides

Advertisement

Quick Links

Corded roman blind kit
with cord guides
Please check the contents
headrail
support
headrail
(with end cap)
length
60cm
1
2
90cm
1
2
120cm
1
3
150cm
1
4
180cm
1
4
1. Fabric requirements for your window size
1. A Measure the width and drop of your window for
recess fixed headrail or if you have mounted your
blind headrail outside the recess, measure the width
of the blind headrail by the drop required.
1. B Add to the finished blind the measurements shown
in diagram B.
On wider blinds more than a fabric width wide, join
the fabric so the blind will have seams an equal
distance from the centre. Mark the blind size plus
seams with tailors chalk. Trim out the size.
2. Sewing the side seams
Working on the back of the fabric, fold the side fabric
under 0.5cm ( 3 / 16 ") and then over 1cm ( 3 / 8 ") to
form a seam and sew down the inner edge.
Repeat for the opposite side.
3. Stitching the loop tape to the top of the blind
Remove loop tape from headrail
3. A Fold over the top of the fabric 1cm ( 3 / 8 ").
3. B Place the loop tape over the fold leaving a
0.5cm ( 3 / 16 ") gap between the tape and the
top of the fold. Sew the tape into place with
two rows of stiches - a row on top and a
row on the bottom of the tape.
4. Sewing the bottom bar pocket
Fold over and create a 4cm (1 5 / 8 ") pocket with a
turn over of 1cm ( 3 / 8 ") as shown in the diagram.
Stitch along the top edge hem/pocket.
cord guide
cord pulley
split cord
(with cords)
collector
2
1
1
3
1
1
3
1
1
4
1
1
4
1
1
Thank you for purchasing this product. Please read the
instructions and warnings carefully before use to ensure
safe and satisfactory operation of this product. It is
recommended that this blind should only be installed
by persons competent in DIY.
cord pull
cord
roman
cleat
rods
1
1
5
1
1
5
1
1
5
1
1
5
1
1
5
1
A
FINISHED
BLIND SIZE
B
( 3
1cm
TOP
Measure width
1.5cm
( 5
/
8 ")
5cm (2")
BOTTOM
( 3
1cm
/
8 ")
2
( 3
0.5cm
/
3
A
( 3
1cm
/
8 ")
4
( 3
1cm
/
8 ")
5
4cm
1
/
(
8 ")
bottom
hook on
loop
bar
cord toggle
tape
1
2
0.61 Mtr
1
3
0.91 Mtr
1
3
1.21 Mtr
1
4
1.51 Mtr
1
4
1.81 Mtr
Recess fix
headrail
finished
blind size
/
8 ")
1.5cm
Drop including top
( 5
/
8 ")
tape seam and bottom
bar pocket seam
Fabric join
seam
1cm
( 3
/
8 ")
( 3
0.5cm
/
16 ")
16 ")
0.5cm
B
pocket roman
screws &
blind tape
wall plugs
3.2 Mtr
4
4.7 Mtr
4
6.2 Mtr
5
7.7 Mtr
6
9.2 Mtr
6
headrail
finished
blind size
Fabric join
seam
Width including
side seams
( 3
/
16 ")

Advertisement

loading

Summary of Contents for John Lewis Corded roman blind kit

  • Page 1 Thank you for purchasing this product. Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product. It is Corded roman blind kit recommended that this blind should only be installed with cord guides by persons competent in DIY.
  • Page 2 5. Marking the tape positions Divide the distance between the top and bottom of the blind by 6 and mark at both sides the position. With tailors chalk draw a faint line across the blind. Note: Ensure the lines are parallel before sewing blind in step 6.
  • Page 3 10. Trimming the headrail Tool required is a hacksaw. 10. A Remove the headrail end cover. 10. B Trim the track with a fine hacksaw. 10. C Re-fit the the end cover. 11. Positioning the cord guides along the back of the headrail Note: If you require a left hand draw see point 18 before repositioning the cord guides.
  • Page 4 The head rail shall not be installed less than 1.5m from the floor. For further information go to: www.makeitsafe.org.uk Keep out of the reach of young children. Small parts - choking hazard. John Lewis Partnership 171 Victoria Street Batch code: London SW1E 5NN johnlewis.com...