1. Manuals
  2. Brands
  3. Flintec Manuals
  4. Touch terminals
  5. FT-112
  6. Technical manual

Flintec FT-112 Technical Manual

Panel weighing terminal
Hide thumbs
Table of Contents

Advertisement

Quick Links

FT-112(D) Panel
Weighing Terminal
Technical Manual

Advertisement

Table of Contents
loading

Related Manuals for Flintec FT-112

Summary of Contents for Flintec FT-112

  • Page 1 FT-112(D) Panel Weighing Terminal Technical Manual...

  • Page 2: Table Of Contents

    Disposal ............................17 Housing ............................. 18 Mechanical Installation ........................18 Electrical Connections ........................19 4.6.1 Analogue Load Cell Connection (Only FT-112 Panel) ..............19 4.6.2 Digital Load Cell Connection (Only FT-112D) .................. 20 4.6.3 RS232C Serial Port ........................... 21 4.6.4 RS485 Serial Port ..........................
  • Page 3 GSD Configuration .......................... 129 14.1.3 Profibus DP Data Structure ......................129 Profinet ............................130 14.2.1 Data Format ............................ 131 14.2.2 Profinet Parameters ........................131 14.2.3 GSDML Configuration ........................131 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 2 of 170...
  • Page 4 Appendix 1: Data Structure Profibus, Profinet, EtherNET/IP, EtherCAT, CC-Link, Powerlink, CC-Link IE ........146 Appendix 2: Data Structure - CANopen ......155 Sealing of Approved Scale ..........165 Trouble Shooting ..............166 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 3 of 170...
  • Page 5 FLINTEC GmbH reserves the right to revise this manual and alter its content without notification at any time. Neither FLINTEC GmbH nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or failure to strictly comply with FLINTEC GmbH operating and maintenance instructions.

  • Page 6: Safety Instructions

    SECONDS BEFORE ANY CONNECTIONS OR DISCONNECTIONS ARE MADE. FAILURE TO OBSERVE THESE PRECAUTIONS COULD RESULT IN DAMAGE TO OR DESTRUCTION OF THE EQUIPMENT OR BODILY HARM. CAUTION! OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 5 of 170...

  • Page 7: Declaration Of Conformity

    This declaration certifies the conformity with the listed Diese Erklärung bescheinigt die Übereinstimmung directives, but it is no promise of characteristics. mit den genannten Richtlinien, beinhaltet jedoch keine Zusicherung von Eigenschaften. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 6 of 170...

  • Page 8: Introduction

    PLC in the cabinet for only having remote IO’s. The scales equipped with FT-112(D) Panel weighing indicator can be used in all kind of industrial areas up harsh to wet and hygienic environments with its fast and efficient cleaning that was designed and built according to the international guidelines.
  • Page 9 Any output(s) can be used as a Remote output of your PLC over BSI or Modbus. Analogue Output (opional) Voltage output 0-5 VDC, 0-10 VDC Current output 4-20mA, 0-20mA Resolution 60 000 steps FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 8 of 170...
  • Page 10 Min. 4 ms response delay after read/write commands Digital inputs and outputs of the instrument can be programmed independently as Remote IO a Remote IO’s of PLC to control them over fieldbus. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 9 of 170...
  • Page 11 Remote IO’s of PLC to control them over fieldbus. Powerlink (optional) Supports Ethernet POWERLINK V2.0 Communication Profile Specification Compatibility version 1.2.0 Data rate 100 Mbit/s, half duplex XDD file XDD-file provided Ring redundancy Available FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 10 of 170...
  • Page 12 1,4 kg (3,07 lb) Packing sizes 273 x 190 x 153 mm (10,75 x 7,48 x 6,02”) (W x H x D) Weight Packed 2,5 kg (5,51 lb) FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 11 of 170...

  • Page 13: The Front View And Key Functions

    Figure 3.1 – Front view of FT-112(D) Panel 3.3.1 Display The bright and wide-angle LCD display of the FT-112(D) Panel instruments is shown below. The meanings of the announcement symbols on the display: 6-digit 22 mm height big weighing display with sign 16-digit 8 mm height alphanumeric information display High resolution digit separator.

  • Page 14: Key Pad

    Announces the keys are locked. Announces the time unit of the parameter value is millisecond or second. 3.3.2 Key Pad The keys and the key functions of FT-112(D) Panel: Page 56, 35, 81, Programmable Function key This programmable key is set for 84, 86, 90, 94, your easy use in your application.
  • Page 15 Press for more than 2 seconds to clear the data on the display at data entry. Help Press the key consecutively to learn functions of programmable keys. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 14 of 170...

  • Page 16: Passwords

    RELATED PARAMETERS: Sub-block 26- . 3.4.1 Keylock FT-112(D) Panel has the capability to lock the keys to avoid unauthorized interfere. The key(s) which would be locked are programmed in the setup at sub-block 34- . Key lock password default is 11.

  • Page 17: Installation

    If the energy condition of your plant is not good enough, prepare a special power line for DC power supply in the cabinet. The quality of your plant grounding will provide weighing accuracy and the safety of FT-112(D) Panel. If grounding of your plant is not good enough, prepare a special grounding.

  • Page 18: Location Of The Peripheral Connections

    Disconnect the instrument from power source before start cleaning for your safety. FT-112(D) Panel weighing indicator is designed for using in wet, hygienic and harsh environment. To maintain the instrument, never use harsh abrasive cleaners or solvents. Wipe the instrument with a soft cloth slightly dampened with warm soapy water or with mild detergent.

  • Page 19: Housing

    Mechanical Installation Before starting the installation, prepare the weighing indicator location on the cabinet front. Prepare the Protective Earth (PE) cable to grounding the FT-112(D) Panel housing. The protective earth should be as good as possible for scale reliability. Use high quality and EMC certified DC power source in the cabinet.

  • Page 20: Electrical Connections

    6 wire load cell connection Junction box connection. Wiring between instrument and junction box will be 6 wire. Figure 4.3 – The analogue load cell and junction box connection. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 19 of 170...

  • Page 21: Digital Load Cell Connection (Only Ft-112D)

    Platform Figure 4.5 – Installation with junction box to power supply DLC #1 Instrument Cable DLC #2 FT-112D DLC #n Cabinet Platform Figure 4.6 – Daisy-chain installation FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 20 of 170...

  • Page 22: Rs232C Serial Port

    4.6.3 RS232C Serial Port FT-112(D) Panel weighing indicator has RS232C serial port which is galvanically isolated from other circuitry to increase the EMC immunity. The usage of this serial port and its specifications are described in the Table 4.3 and its pin configuration is shown in Table 4.4.

  • Page 23: Rs485 Serial Port

    Table 4-6 – Pin configuration of RS485 terminal RS485 serial connection is done with two wires as indicated below in Figure 4.9. 3 ……………… 31 Figure 4.9 – Multi instrument connection with PLC FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 22 of 170...

  • Page 24: Rs422 Serial Port

    You may use RS422 port as a 2nd RS485 port after adding 2 short circuits between the terminal pins as shown below. ………… Figure 4.11 – The second RS485 port usage of RS422 port (half duplex). FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 23 of 170...

  • Page 25: Ethernet Tcp/Ip

    Figure 4.12 - HUB connection The PC connection cabling is done via cross cable as shown below. IP address blocks and gateway address of FT-112(D) Panel and PC should be the same in cross connection. Figure 4.13 - PC connection with cross cable Important note: Disconnect Indface2x set up PC software before Ethernet interfacing.

  • Page 26: Profibus Pb

    Terminated Not used Terminated Not used Terminated Shield Chassis ground The HUB connection cabling will be a direct connection as shown below: Figure 4.16 - HUB connection FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 25 of 170...

  • Page 27: Canopen

    CANopen connection is done with four wire as indicated below in Figure 4.18. The data line ends must be terminated with 120 ohm resistors. Figure 4.18 - PLC Connection CANopen Connector pin configuration (DB9M) Signal Description CAN_L CAN_GND CAN_SHIELD CAN_H Housing Cable Shield FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 26 of 170...

  • Page 28: Ethernet/Ip

    The PC connection cabling will be done via cross cable as shown below. IP address blocks and gateway address of weighing indicator and PC should be the same in cross connection. Figure 4.21 - Cross PC connection FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 27 of 170...

  • Page 29: Ethercat

    Figure 4.23 - HUB connection 4.6.12 CC-Link Figure 4.24 - PLC Connection CC-Link Connector pin configuration Signal Description PositiveRS485 Rxd/TxD NegativeRS485 Rxd/TxD Signal ground Cable Shield Protective Earth FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 28 of 170...

  • Page 30: Powerlink

    Transmit/Receive 4 negative Connected to FE through a 1 nF capacitor and a 1 Housing Shield Mohm resistor. Note that the connector shields are separated to prevent ground currents. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 29 of 170...

  • Page 31: Usb Port

    Alibi memory requires the Alibi SD card at the SD1 card slot on the bottom of the main board as shown in the pictures below. The alibi memory SD card can be ordered from Flintec or his dealer. Figure 4.28- Location of Alibi SD card slot Inserting or removing the Alibi SD card 1.

  • Page 32: Installation Of Sd Card

    4.6.17 Installation of SD Card Some features of the FT-112(D) Panel requires SD card like Modbus RTU / TCP. Its slot is located on the rear of the instrument. These SD cards should be ordered for your use. Insert the SD card 1.

  • Page 33: Analogue Output Connection

    4.6.21 Power Source Connection and Grounding Connect DC power supply of FT-112(D) Panel to the noise proof power line due to the weighing instrument measures very low signal levels. The quality of the power line and DC power supply will determine the accuracy and the safety of your measuring system.

  • Page 34: D) Functions

    Taring Taring is used to determine a net weight of a material if any tools like containers are needed. The weight of these tools can be eliminated. FT-112(D) Panel weighing indicator has 2 different taring features. Subtractive tare This taring type is the mostly used way which tare value reduce the weighing range in Net as...
  • Page 35 161. Indface2x PC software is used to program EPL printout data and download to the instrument for free programming the data output or for label printing including barcode. Refer to page 49, and 111 for details. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 34 of 170...

  • Page 36: Advanced Functions

    Refer to page 55. Preset Taring with numeric entry: 1. Press key. 2. Enter tare value numerically. 3. Press key for taring or press key to escape. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 35 of 170...
  • Page 37 Enabled net sign correction affects the display and printed data. Displaying and Net sign correction Net sign correction printout disabled enabled Tare 120.0 kg 30.0 kg Gross 30.0 kg 120.0 kg - 90.0 kg 90.0 kg FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 36 of 170...
  • Page 38 In the example below 70% of the capacity is used and 30% is available. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 37 of 170...

  • Page 39: Alibi Memory

    You may display the alibi record by selecting the criteria, which are alibi number, date, net weight, gross weight or tare weight. You also may transfer alibi memory records to your PC. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 38 of 170...
  • Page 40 1. Go to the parameter [ 8-- METROLOGY ] main block in set up. 2. Press key 6 times to access parameter 815. 3. Press key to print alibi information. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 39 of 170...
  • Page 41 The empty fields are indicated as [ ------- ] and transferred as [ NO RECORD ]; and the corrupted records are indicated as [ Error ] and transferred as [ CORRUPTED ]. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 40 of 170...

  • Page 42: Programming And Calibration

    A set-up DIP switch is located near the load cell connector at the FT-112 (D) panel rear side as shown in the figure below and its position should be “ON” (downward) to change the metrological related parameters including calibration.

  • Page 43: Quick Access To Frequently Used Parameter Blocks

    [ WAIT ] message will be shown on the display for a little while, and the weighing indicator returns to the weighing mode. Don’t forget to switch off the instrument and bring the calibration DIP switch to the position “OFF” WARNING: before using your scale in trade. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 42 of 170...

  • Page 44: Programming And Parameters

    Programming and Parameters FT-112(D) Panel weighing indicator is programmed in seven main blocks, which are serial interface, configuration, application, scale, calibration, metrology and diagnostic. Main blocks in the programming menu are displayed like [1-- INTERFACE ] and sub-blocks are displayed like [11- RS232C ].
  • Page 45 Even parity CSUM : NO Checksum at continuous and BSI formats. Checksum disable Checksum enable : YES Carriage return at continuous formats. Carriage return disable Carriage return enable FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 44 of 170...
  • Page 46 38K4 : 38400 4800 4800 57K6 : 57600 9600 9600 LENGHT Data Length 7 bits 8 bits PARITY : NO Parity No parity Odd parity EVEN Even parity FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 45 of 170...
  • Page 47 Flintec LM2 (BX1 par.000=6) BAUD : 9600 Baud rate 1200 1200 19K2 : 19200 2400 2400 38K4 : 38400 4800 4800 57K6 : 57600 9600 9600 LENGHT Data Length FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 46 of 170...
  • Page 48 Available functions are shown on the weight display after pressing key sequentially. Press key after selecting the data format. Refer to Appendix 5 for details data structure. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 47 of 170...
  • Page 49 Commonly used by PT, Rinstrum, HBM, GSE. AVERY Commonly used by Avery E1205. BASTER Commonly used by Baster. Flintec LM2 ( BX1 par.000=6 ) : 250 IP address. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 48 of 170...
  • Page 50 Multiline Format 1 for 16 Character printer 16F2 Multiline Format 2 for 16 Character printer 26F1 Multiline Format 1 for 26 Character printer 26F2 Multiline Format 2 for 26 Character printer EPL Format FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 49 of 170...
  • Page 51 LF BEFO : +2 Line feed before printout. + = Forward , - = Backward NO,1,2….9 : Line feed quantity before data. Example: +2 means 2-line feed forward. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 50 of 170...
  • Page 52 AUTO ADJ : NO Set analogue output to calibration range Automatic adjustment between min and max limits if changed. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 51 of 170...
  • Page 53 : INTG ] Data format of the CANopen INTG Signed 32-bit integer, no decimal point implied. FLOA 32 bit float, decimal point implied. ADDRESS : 001 Node address 001…127 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 52 of 170...
  • Page 54 Data format of the Powerlink INTG Signed 32 bit integer, no decimal point implied. FLOA 32 bit float, decimal point implied. ADDRESS : 001 Node address 001…239 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 53 of 170...
  • Page 55 TIME : D+T Information data on the right of the alphanumeric display. No clock data on the display. Display time, Display date, Display date and time, FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 54 of 170...
  • Page 56 Very high filter. Slowest and the most stable weighing. VHIG : ENG User language. LANGUAGE English Deutsch Français İtaliano Espagnol Türkçe NET SIGN : NO Net sign correction at displaying and printing. Disabled. Enabled. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 55 of 170...
  • Page 57 Date setting XX.XX.XX Page 37 TIME SET : Time adjust HH:MM Page 110 Consecutive number 1…65535 S. NAME : SCAL Scale name. Maximum 16 characters. Default is SCALE-1 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 56 of 170...
  • Page 58 : ALL SmartAPP displaying. SmartAPP displaying is disabled. Only bar graph operates. COLO Only display color warns the operator. Bar graph and display color functions are activated. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 57 of 170...
  • Page 59 [ 326 OUTPUTS : STAB ] checkweighing. (Appears if the option is installed) IMME Immediately change even scale is not stable. STAB Change if the scale is stable. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 58 of 170...
  • Page 60 LOCK Locked [ 348 ZEROING : USE Zeroing key locking Not locked LOCK Locked Δ KEY Δ key locking [ 349 : USE Not locked LOCK Locked FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 59 of 170...
  • Page 61 [ 352 INPUT 2 : NO Input 2 Page 95, [ 353 INPUT 3 : NO Input 3 Page 95, [ 354 INPUT 4 : NO Input 4 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 60 of 170...
  • Page 62 For example: if the scale division is 0.5 kg and this parameter entry is 1.0 division. The output is activated if the indication is lower than 0.5 kg. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 61 of 170...
  • Page 63 Maximum 16 characters. Default is ID2. Page 77 [ 375 ID2 LINK : NO Linked memories to ID2 memory No any linked memory. Set memory PT memory. SET and PT memories. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 62 of 170...
  • Page 64 Power on zero. Disable. ± 2% 2%LK ± 2%, [POWER ON ZERO ERR] prompt cannot be erased. Call service. ± %10 15-5 + %15, - %5 ± %20 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 63 of 170...
  • Page 65 Select NO, g, kg, t, lb, klb, N or kN. [ 522 RANGE : SING Scale range SING Single Range 2 x Multi Range 3 x Multi Range 2 x Multi Interval 3 x Multi Interval FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 64 of 170...
  • Page 66 [ 544 SET TO 1 : NO Temporarily set shift constants to 1 Normal operation (entered shift constants are used). Test mode (shift constants are equal to 1). FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 65 of 170...
  • Page 67 The load weight used at the calibration is indicated here. ZERO COEFFIC This coefficient is determined the zero point of the scale. GAIN COEFFIC This coefficient is related with the gain factor of the scale. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 66 of 170...
  • Page 68 This non-resettable and protected counter announces CONFIG COUNT interfering quantity to the instrument. Count number increases at every exit from set-up mode. NEXT VERIFIC Date of the next verification FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 67 of 170...
  • Page 69 The last 20 under errors listed in this parameter. ERROR LOGS The last 20 errors listed in this parameter. ENTRY LOGS The last 20 Service/User entry listed in this parameter. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 68 of 170...
  • Page 70 WARNING: The DLC must be disconnected from the network and connect as single. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 69 of 170...

  • Page 71: Calibration

    Calibration involves emptying the scale then placing a known test weight on an empty platform and allowing FT-112(D) Panel to capture values for zero and span. Calibration is performed as; 1. Press key at the [ 611 TEST WEIGHT ] prompt to start the calibration.
  • Page 72 2. At the [ LOAD THE SCALE ] [ XXXXXX ] prompt, the test weight value will be used for the calibration shown on the display. Enter the test weight value via numerical keys. A minimum test load requirement is 20% of scale capacity for accurate calibration. FLINTEC recommends test load between 50% to 75% of the capacity.
  • Page 73 Dead load value is cancelled after automatic zero adjustment. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 72 of 170...
  • Page 74 Note these coefficients to use them in case of calibration lost. Changing them slightly improves the scale accuracy without recalibration. Entering these values to another indicator may cause slightly reducing the weighing accuracy due to offset differences between two analogue digital circuits. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 73 of 170...
  • Page 75 Typical application of sectional pairs is rolling loads on the platform like truck scales. Sectional pairs adjustment is easier and faster. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 74 of 170...
  • Page 76 2. It will be [ 544 SET TO 1 : NO ], press key until [ SAVE : YES ] prompt shown on the display. 3. Press key to save the changes into the memory. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 75 of 170...
  • Page 77 RELATED PARAMETERS: Sub-block 37- . FT-112(D) Panel weighing indicator has 2 identification keys ID1 and ID2 positioned under the display for storing identification data. Each identification key has an alphanumeric identification name and data. The identification data can be saved into the ID1 and ID2 memories, each has 500 pieces 32-character identification data record size.
  • Page 78 ID1, which are displayed in sequence. The instrument returns to the operation mode after loading the selected item. 5. Or press key to return without any select. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 77 of 170...
  • Page 79 Digital inputs and outputs may change their status immediately or if the weight is stable. Refer to page 58. If there is any non-used port in the application, it can be programmed freely. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 78 of 170...
  • Page 80 The classifying can be used at automatic sorting machines for classifying up to 5 ranges, if automatic start or start input features are used. Figure 10.1 - Timing diagram of automatic classifying operation. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 79 of 170...
  • Page 81 : 100,0 ] prompt appears on the display. Enter new value with numerical keys. 10. Press the key to go to the following memory after saving it or press key to return operation without saving. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 80 of 170...
  • Page 82 − − Tolerance (very light) Output-1 − − Tolerance (light) Output-2 Output-3 Output-4 + Tolerance (heavy) Output-5 + + Tolerance (very heavy) Table 10-1- Digital inputs and outputs of Classifying. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 81 of 170...
  • Page 83 Automatic operation starts if the load is heavier than Empty range. The scale is accepted unloaded if the weight is in the Empty range. The checkweighing operation is shown in diagram below; Figure 10.3 - Timing diagram of checkweighing operation. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 82 of 170...
  • Page 84 3. Enter the memory code of the product by pressing the numerical keys and press key. 4. The selected product limits are loaded for usage after displaying values. 5. Or press key to exit without selecting the product from memory. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 83 of 170...
  • Page 85 Output-1 Output-2 Output-3 + Tolerance ( heavy ) Output-4 Refer to parameter 364 Output-5 Refer to parameter 365 Table 10.2 - Digital inputs and outputs of Checkweighing. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 84 of 170...
  • Page 86 Filling application is used for weighing materials into the container. The scale is accepted as loaded if the gross weight is bigger than Empty range. The Filling operation timing diagram, FT-112(D) Panel outputs and SmartAPP bar is shown in the Figure 10.5 below.
  • Page 87 7. The [ TAREMIN : 0,60 ] prompt appears on the display. Enter new value with numerical keys. Press key to save it or press key to return operation without saving. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 86 of 170...
  • Page 88 Refer to parameter 354 Output-1 Ready Output-2 Fine Output-3 Coarse Output-4 End of Filling Output-5 Refer to parameter 365 Table 10.3 - Digital inputs and outputs of filling. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 87 of 170...
  • Page 89 Test starts automatically or manually if the force is bigger than. The MID DECR and END DECR entries can be setup as value or percent (refer to par. 312 ) and others are always values. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 88 of 170...
  • Page 90 3. Enter the memory code of the product by pressing the numerical keys and press key. 4. The selected product limits are loaded for usage after displaying values. 5. Or press key to exit without saving. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 89 of 170...
  • Page 91 Refer to parameter 354 Output-1 Ready Output-2 Output-3 End of Testing Output-4 Alarm Output-5 Refer to parameter 365 Table 10.4 - Digital inputs and outputs of peak hold. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 90 of 170...
  • Page 92 Totalization FT-112(D) Panel can be used for horizontal or vertical totalization operations. Vertical totalization means individual and cumulative weighing of the different materials batched in the same container. The horizontal totalization is used for weighing materials of batch in the separate containers or for totalizing sequential weighing.
  • Page 93 3. [ Delete ? ] prompt appears. 4. Enter the key password if programmed. Refer to parameter 325. 5. Press key to delete or press key to exit without clearing the total. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 92 of 170...
  • Page 94 Digital inputs and outputs are set to their functions in sub-blocks 35- and 36- at basic weighing operation. Digital inputs can be programmed for zeroing, taring, print etc. in sub-block 35-. Digital outputs can be programmed for the different functions as described below. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 93 of 170...
  • Page 95 4. Repeat from step 2 for entering following setpoints. 5. FT-112(D) Panel returns to the operation after displaying setpoint 5 and entering its value, 6. Press key to return operation at any step.
  • Page 96 Refer to related fieldbus command table to receive the status of inputs. This usage is independent from the weighing process of the instrument. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 95 of 170...
  • Page 97 VIN-LOW Window, active low Output goes to low if absolute indicated weight is between setpoint high and setpoint low. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 96 of 170...
  • Page 98 THR-HI Threshold, active high Output goes to high if indicated weight is heavier than setpoint high. Returns the low if the weight is less than setpoint low. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 97 of 170...
  • Page 99 Output goes to high if indicated weight is between setpoint high and setpoint low. VIN-LOW Window, active low Output goes to low if indicated weight is between setpoint high and setpoint low. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 98 of 170...
  • Page 100 VIN-LOW Window, active low Output goes to low if absolute net weight is between setpoint high and setpoint low. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 99 of 170...
  • Page 101 THR-HI Threshold, active high Output goes to high if net weight is heavier than setpoint high. Returns the low if the weight is less than setpoint low. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 100 of 170...
  • Page 102 Output goes to high if net weight is between setpoint high and setpoint low. VIN-LOW Window, active low Output goes to low if net weight is between setpoint high and setpoint low. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 101 of 170...
  • Page 103 Output goes to high if gross weight is between setpoint high and setpoint low. VIN-LOW Window, active low Output goes to low if gross weight is between setpoint high and setpoint low. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 102 of 170...
  • Page 104 Digital outputs, which are not used at this mode, can be programmed freely to any other function. For example, if SP5 is not needed to control, it can be programmed to the zero range to produce empty signal. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 103 of 170...
  • Page 105 The digital output(s) can be controlled from PLC as a Remote output if the instrument is equipped with any fieldbus option. Refer to related fieldbus command table to activate or deactivate the outputs. This usage is independent from the weighing process of the instrument. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 104 of 170...
  • Page 106 For example, the Output 5 of the Filling is not used by the Filling application software and it can be used as zero range output to check the scale unloading. Refer to SmartAPP section 11.2, page 94, for usage of digital inputs and outputs details. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 105 of 170...
  • Page 107 If you transmit ASCII codes P(print), Z(zero), T(tare) or C(clear) letters to the serial port of FT-112(D) Panel; it will act like the related key is pressed.
  • Page 108 12.1.1 Continuous Data Formats RELATED PARAMETERS: Parameters 111, 121, 131, 141 and 151. Continuous data output can be programmed to the same common formats besides Flintec continuous format. To select one of the described formats below press the key sequentially. Press key to go to the next parameter.
  • Page 109 Unit of weight value are kg, g, lb, klb, N or kN as left aligned. Carrige Return ( 0D hex ) ® Sartorious Description Ignore Sign SP Indicated weight SP Unit CR LF Example FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 108 of 170...
  • Page 110 Sartorious. ® Rinstrum is a registered trademark of Rinstrum. ® Avery is a registered trademark of Avery Weigh-Tronix. ® Baster is a registered trademark of Baster. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 109 of 170...
  • Page 111 Footer * Thank you * * Thank you * 16F1 – Includes only Gross or 16F2 – Includes Gross or Gross\ Net weight value Tare\Net weight values FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 110 of 170...
  • Page 112 The EPL format of the data output in Print mode is selected to print the label data in graphical format EPL. You can design your label in EPL format by using the printer label design software and Flintec software as describe below.
  • Page 113 BSI Data Structure for Dialog with PC and PLC New generation FLINTEC weighing indicators launched on the market support the standardized command set BSI data form, depending on the functionality of the instrument. This easy data format gives the reliable and speedy interface advantages with communicating PLC or PC for process control or transactional applications.
  • Page 114 ID2 name and data read DK 2 DKA [16d name ] [32 digits data] Write SmartAPP and apply DB+[8 digits Limit-1]+[8d Limit-2] +[8d Limit-3]+[8d Limit-4]+[8d Limit- 5]+[8d Limit-6] FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 113 of 170...
  • Page 115 0 − (0x30 + 0x31 + 0x50 + 0x53 + 0x2B + 0x30 + 0x30 + 0x30 + 0x31+ 0x32 + 0x33 + Checksum 0x2E + 0x34) 0 − 0x02B7 0x49 Char ‘4’ and Char ‘9’ FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 114 of 170...
  • Page 116 (Weight is stable and 123.4) or 01PN (Could not print) Comments: Checks status and it must be stable. Else Nack status is send. Status can be Stable or Nack. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 115 of 170...
  • Page 117 Data length change according to number of digital inputs. Inputs are implemented to ASCII char of 4-bit. ‘1111’ inputs are implemented to char ‘F’. INPUTS Bit wise ASCII FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 116 of 170...
  • Page 118 Status must be stable in 2 seconds time out delay. If so, Ack is send. If it cannot be stable in time out delay, Nack is send. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 117 of 170...
  • Page 119 FT-112(D) Panel has analogue output which is programmable to 4 – 20 mA, 0 – 20 mA, 0 – 5 V or 0 – 10 V. Analog output is automatically adjusted to the weighing range after the calibration. The mid value of the analogue output is set to zero load at bipolar usage.
  • Page 120 IMPORTANT NOTE: Modbus RTU and Modbus TCP interfaces require Modbus SD card at the SD2 card slot on the rear of the instrument. FT-112(D) Panel controller has a Modbus RTU interface over RS485, RS422 or RS232C serial port and Modbus TCP/IP over Ethernet TCP/IP interface. These interfaces can be programmed to High-Low or Low- High for different type of PLC’s.
  • Page 121 40021 Grand Total Use Dword at floating point operation Definition None Zero Tare Clear 40025 Commands Print Reprint the last label High resolution enable High resolution disable FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 120 of 170...
  • Page 122 40067 Peak value 40069 Peak value Only available for Peak hold application. 40071 Peak value Refer to Section 10.4, page 88. Peak value 40073 Peak value 40075 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 121 of 170...
  • Page 123 (Kilonewton) (Kilolibre) Single range 2 x MR 40155 Range 3 x MR 2 x MI 3 x MI 40157 MAX-1 Refer to parameter [523] on page 65 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 122 of 170...
  • Page 124 Total Load Cell capacity for eCal eCal 40191 Average mV/V value for eCal Coefficients 40193 Dead load value for eCal Definition Calibration 40195 Process Status Ready for calibration FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 123 of 170...
  • Page 125 Information display ID1T ID2T Refer to parameter [314] page 58 40261 SmartAPP displaying COLO Refer to parameter [316] page 58 RAAY 40263 Display color change YAAR RBAY FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 124 of 170...
  • Page 126 Exception codes: 1: Function code is not supported. 2: Out of beginning and ending address range. 3: Invalid value entrance or wrong byte number. 4: Operation error. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 125 of 170...
  • Page 127 (Input-2 is active) Read digital outputs 01,03,00,2A,00,02,E5,C3 Answer of digital outputs 01,03,04,00,00,00,04,FB,F0 (Output-3 is Active) Read Setpoint-1 01,03,00,2C,00,02,05,C2 Answer of Setpoint-1 01,03,04,00,00,03,E8,FA,8D Load Set point 1 = 5000 01,10,00,2C,00,02,04,00,00,13,88,FC,B4 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 126 of 170...
  • Page 128 IMPORTANT NOTE: Modbus RTU and Modbus TCP interfaces require Modbus SD card at the SD2 card slot on the rear of the instrument. Ethernet output of FT-112(D) Panel is programmable to BSI command set, Continuous data output, Fast continuous data output, Modbus TCP/IP High-Low, Modbus TCP/IP Low-High. The first three data structures, as shown in the table below, are described in the related sections.
  • Page 129 There is an exception error 14.1.1 Data Format Data format of weight value can be programmable for Floating point (IEEE 754) or Integer. Refer to parameter 191. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 128 of 170...
  • Page 130 Dword (PLC Output to FT-112(D) Panel Input) Output 2 words Dword (PLC Output to FT-112(D) Panel Input) 14.1.3 Profibus DP Data Structure For the Data Structure for Profibus see Appendix 1, page 146 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 129 of 170...
  • Page 131 LED State Description Comment No Link No link, no communication present Ethernet link established, no Green Link communication present Ethernet link established, Green, flickering Activity communication present FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 130 of 170...
  • Page 132 Ethernet parameters can be adjusted by keys in programming mode. Refer to parameter block [15-]. Additionally, Ethernet parameters can be set up by Indface2x PC software over Local Network Area or by Flintec´s set up PC software. Both software are available on www.flintec.com Station name is ‘scale-1’...
  • Page 133 Dword (PLC Output to FT-112(D) Panel Input) Output 2 word_2 Dword (PLC Output to FT-112(D) Panel Input) 14.2.4 Profinet Data Structure For the Data Structure for Profinet see Appendix 1, page 146 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 132 of 170...
  • Page 134 CANopen After setting related parameters you can communicate with FT-112(D) Panel via CANopen network. EDS file is available in on internet www.flintec.com. Automatically detected and supported baud rates are 10 kbps, 50 kbps, 100 kbps, 125 kbps, 250 kbps, 500 kbps, 800 kbps, 1 Mbps, Autobaud (default).
  • Page 135 RxPDO 1 (4 words) Unsigned Long (PLC Output to FT-112(D) Panel Input) 14.3.3 CANopen Data Structure For the Data Structure for Profinet see Appendix 2, page 155 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 134 of 170...
  • Page 136 You may change the port, if there is any malfunction on port in usage. The EtherNet/IP interface supports 10/100Mbit, full or half duplex operation. EDS file for two port EtherNet/IP is available on internet www.flintec.com There are 4 announcement LEDs on the instrument to indicate the interface status as shown below.
  • Page 137 Ethernet parameters can be adjusted by keys in programming mode. Refer to parameter block [19-]. Additionally, Ethernet parameters can be set up by Indface2x PC software over Local Network Area or by Flintec´s set up PC software. Both software are available on www.flintec.com...
  • Page 138 Dword (PLC Output to FT-112(D) Panel Input) Output 2 words Dword (PLC Output to FT-112(D) Panel Input) 14.4.4 EtherNet/IP Data Structure For the Data Structure for EtherNET/IP see Appendix 1, page 146 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 137 of 170...
  • Page 139 The EtherCAT interface supports 100Mbit, full duplex operation. ESI file for two port EtherCAT is available in on internet www.flintec.com. There are 4 announcement LEDs on the instrument to indicate the interface status as shown below. The meanings of these LED’s are;...
  • Page 140 Dword (PLC Output to FT-112(D) Panel Input) DO RxPDO-Map SubIndex 002 Dword (PLC Output to FT-112(D) Panel Input) 14.5.3 EtherCAT Data Structure For the Data Structure for EtherCAT see Appendix 1, page 146 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 139 of 170...
  • Page 141 CC-Link After setting related parameters you can communicate with FT-112(D) Panel via CC-Link network. Supported CC-Link version is v1.10 and baud rates are 156 kbps (default), 625 kbps, 2,5 Mbps, 5 Mbps and 10 Mbps. There are 2 LED’s near the CC-Link connector which are;...
  • Page 142 Description RWr0, RWr1 Dword Input (FT-112(D) Panel Output to PLC Input) Remote Register ( RWr ) RWr2, RWr3 Dword Input (FT-112(D) Panel Output to PLC Inpu ) Remote Input ( RX ) RX0 ~ RX31 Not used RWw0, RWw1 Dword Output (PLC Output to FT-112(D) Panel Input)
  • Page 143 If the STATUS LED is red, a fatal event was encountered. In the case of red LED warning, check cabling, configuration, IP address and device name. Power off the instrument and reenergize the instrument 30 seconds later. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 142 of 170...
  • Page 144 Dword (PLC Output to FT-112(D) Panel Input) 2_Dword_Output_I2002_S02Out Dword (PLC Output to FT-112(D) Panel Input) 14.7.3 Powerlink Data Structure For the Data Structure for Powerlink see Appendix 1, page 146 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 143 of 170...
  • Page 145 CC-Link IE Field After setting related parameters you can communicate with FT-112(D) Panel via CC-Link network. (in preparation). There are 2 LED’s near the CC-Link connector which are; ( A ) NS/RUN LED ( B ) AS/ERROR LED Link/Activity LED (port 1)
  • Page 146 Dword Output (PLC Output to FT-112(D) Panel Input) Remote Output (RY) RY0 ~ RY31 Not used 14.8.3 CC-Link IE Data Structure For the Data Structure for Powerlink see Appendix 1, page 146 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 145 of 170...
  • Page 147 Preset tare is passive Preset Tare Preset tare is active Centre of Weight is out of zero range zero Weight is in zero range Gross Indication Stability Stable Detection Unstable FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 146 of 170...
  • Page 148 Passive High resolution status Active Weight is out of zero range Centre of zero Weight is in zero range Passive Key lock status Active B7-B10 Not used FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 147 of 170...
  • Page 149 - Restart calibration None Span calibration in process … None Zero calibration in process … Not ready for calibration Ready for calibration Table 15-2 - Calibration status FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 148 of 170...
  • Page 150 Empty 10101 Only available for Threshold and SetPoint-1 Low Window feature. 10110 SetPoint-2 Low Refer to sub-block 36-, page 61 to 10111 SetPoint-3 Low see the availabilities. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 149 of 170...
  • Page 151 New CMD Toggle Apply commands which are listed in this table. (1) Write this command after writing values to 1 Dword, then apply this command with New CMD FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 150 of 170...
  • Page 152 Peak value 00111101 Peak value 00111110 Peak value (1) (2) 00111111 Dynamic filter Refer to par. 332 page 59 Very Low 01000000 Filter (1) (2) Medium High FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 151 of 170...
  • Page 153 Refer to par. 523 on page 65 XXXXOO XXXXXO Decimal XXXXXX 01001010 (1) (2) point-1 XXXXX.X XXXX.XX XXX.XXX 01001011 (1) (2) Increment-1 01001100 Capacity-2 (1) (2) Decimalpoint-2 01001101 (1) (2) 01001110 Increment-2 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 152 of 170...
  • Page 154 OVER 318 page 58 CROSS AUTO (1) (2) START MANU 01100111 Refer to par. SAUT 321 page 58 PORT (1) (2) FILLING 01101000 GROS Refer to par. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 153 of 170...
  • Page 155 Programming steps of frequent used commands Reading a weight value: 1. Check the B12…B15 bits of ‘FT-112(D) Panel Output to PLC Input 2 Dword’. 2. If there is not any error, read the weight value ( gross, net or tare ).
  • Page 156 00011 ALL Status (Refer to Table 16-1) Response 00100 Calibration Status (Refer to Table 16-2) 00101 Last print value 00110 Quantity of M+ 00111 Not used 01010 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 155 of 170...
  • Page 157 (Refer to Table 16-3) CMD Flag Toggles The command is applied successfully By default, Actual weight value is represented. B31…B0 To represent other weight or calibration status, refer to B37…B33. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 156 of 170...
  • Page 158 Weight is actual weight Actual Weight or Dynamic Result Weight is dynamic result Dynamic is inactive Dynamic Operation Dynamic weight is calculating Table 16-1– ALL Status table FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 157 of 170...
  • Page 159 - Restart calibration None Span calibration in process … None Zero calibration in process … Not ready for calibration Ready for calibration Table 16-2 - Calibration status FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 158 of 170...
  • Page 160 Not in use Command List Read Data Selection (R_UL1) B37-B33 bits defines the usage of this Dword. PLC Output to FT-112(D) Panel Input RxPDO 1 (R_UL1) RxPDO 1 (R_UL1) descriptions Number B63 … Set / Reset digital outputs B55 …...
  • Page 161 B37-B33 bits defines the usage of this Dword. (1) Write this command after writing values to Low Dword of RxPDO then apply this command with New CMD. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 160 of 170...
  • Page 162 (1) (2) Dynamic filter Refer to par. 332 page 59 00111111 Very Low (1) (2) 01000000 Filter Medium High Very High Disable Power on zero 01000001 ± %2 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 161 of 170...
  • Page 163 XXXXXX Decimal (1) (2) 01001010 point-1 XXXXX.X XXXX.XX XXX.XXX 01001011 Increment-1 (1) (2) (1) (2) 01001100 Capacity-2 Decimalpoint-2 01001101 01001110 Increment-2 (1) (2) (1) (2) 01001111 Capacity-3 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 162 of 170...
  • Page 164 318 page 58 CROSS AUTO (1) (2) START MANU 01100111 Refer to par. SAUT 321 page 58 PORT GROS (1) (2) FILLING 01101000 Refer to par. 322 page 58 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 163 of 170...
  • Page 165 4. The Bit-0 of Calibration Status changes to '1'(set) at the end of the Span calibration. 5. If the Bit-3~Bit-10 of Calibration Status is '1'(set), check the description to understand the calibration error. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 164 of 170...
  • Page 166 EALING OF PPROVED CALE Sealing of Load cell connector Sealing of Calibration switch Alibi SD card sealing FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 165 of 170...
  • Page 167 ROUBLE HOOTING FT-112(D) Panel weighing indicator had been designed as a very reliable and virtually error free instrument. However, if there is an error occurrence, do not attempt to repair the equipment before understanding what caused the error. Note the problems you have with your instrument and the error messages shown on the display.
  • Page 168 - Change main board. The Modbus SD card is not - Order Modbus SD card. E75 MODBUS FAULT installed in SD2 card slot. - Install Flintec Modbus SD card. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 167 of 170...
  • Page 169 - Change the main board. indicator. Capacity of the load cell is E92 DLC UNMATCH - Check capacity of the DLC different. 1) yy = Number/Address of the digital load cell. FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 168 of 170...
  • Page 170 FT-112(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019 Page 169 of 170...

This manual is also suitable for:

Ft-112d

Table of Contents