Related Manuals for Bibby Sterilin TECHNE Tecal 425S
Summary of Contents for Bibby Sterilin TECHNE Tecal 425S
- Page 1 Tecal 425S Calibrator Operator's Manual Issue 5 Date of issue: 3rd May 2005 Techne is a trademark © Techne, 2003...
-
Page 3: Table Of Contents
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L CONTENTS Tecal Calibrator Operator’s Manual page SAFETY AND INSTALLATION English Français Deutsch Español THE CALIBRATOR Applications Warning Specification... - Page 4 T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L PAGE 2...
- Page 5 T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L NOTES PAGE 3...
-
Page 6: English
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L Introduction After use Please read all the information in this booklet before using When you have finished heating samples, remember that the unit. -
Page 7: Français
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L Introduction 6. Les symboles situés sur ou à côté de l’interrupteur de l’appareil ont la signification suivante : Veuillez lire attentivement toutes les instructions de ce I : marche document avant d’utiliser l’appareil. -
Page 8: Deutsch
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L Einleitung 6. Die Symbole auf oder neben dem EIN/AUS-Schalter an der Geräterückseite bedeuten: Bitte lesen Sie diese Bedienungsanleitung komplett bevor : An Sie dieses Gerät benutzen. -
Page 9: Español
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L Introducción 6. Los símbolos que se encuentran en o cerca del Le rogamos lea cuidadosamente la información contenida interruptor de alimentación tienen los siguientes en este folleto antes de manipular el aparato. -
Page 10: The Calibrator
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L THE CALIBRATOR The Tecal Calibrator is designed to provide safe and convenient calibration of a wide range of thermal sensors. It features fast heat up times, with accuracy and repeatability. -
Page 11: Specification
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L Specification The figures stated in the specification are as measured 0-50 mm from the base of the well of the insert, using an SPRT, at the time of calibration. Measuring zone 0 to 50 mm 0"... -
Page 12: When You Switch On
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L WHEN YOU SWITCH ON When you first switch on, the display will show the edition of the software which your unit uses. - Page 13 T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L The DOWN ARROW Button ∇ ∇ ∇ ∇ ∇ When the SET temperature button is held down and the DOWN ARROW button is pressed, the set temperature is decreased.
-
Page 14: Setting The Units For Temperature
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L Over-Temperature Indicator If the unit should, for any reason, exceed the temperature set for the over- temperature cutout (see page 15), the over-temperature indicator will light. -
Page 15: Cooling Probe
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L Cooling Probe Operating temperatures below ambient can be achieved by using the cooling probe with a chilled water circulator. The cooling probe is supplied as an accessory and can be used in an insert with a 3/8"... -
Page 16: Rs232 Serial Interface
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L RS232 SERIAL INTERFACE The calibrator may send data logging information to an IBM PC or compatible computer by connecting the unit and the PC via an RS232 cable, and installing the "Calsoft"... -
Page 17: Technical Information
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L TECHNICAL INFORMATION Brief fault finding notes and lists of replacement parts, accessories and inserts for the Tecal are given in this section. NOTE THAT THIS EQUIPMENT SHOULD ONLY BE DISMANTLED BY PROPERLY TRAINED PERSONNEL. -
Page 18: Replacement Parts
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L Fuses If neither the power light nor display (on the front panel) is lit, one of the two fuses may have blown. -
Page 19: Inserts
T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L Inserts Inserts are made from aluminium or aluminium-bronze and must be ordered separately from the calibrator. Each insert is stamped for identification. A blank insert is available which may be drilled to suit your application. - Page 20 T E C A L 4 2 5 S O P E R A T O R ’ S M A N U A L PAGE 18...
- Page 21 Thank you for reading this data sheet. For pricing or for further information, please contact us at our UK Office, using the details below. UK Office Keison Products, P.O. Box 2124, Chelmsford, Essex, CM1 3UP, England. Tel: +44 (0)330 088 0560 Fax: +44 (0)1245 808399 Email: sales@keison.co.uk...
Need help?
Do you have a question about the TECHNE Tecal 425S and is the answer not in the manual?
Questions and answers