AMES SILVER BULLET 2000SS Series Manual

Double check valve, assemblies & double check detector assemblies

Advertisement

Series 2000SS
Double Check Valve
Assemblies & Double
Check Detector
Assemblies
Sizes: 8" – 12" (200-300mm)
• Installation
• Service
• Repair Kits
• Maintenance
www.amesfirewater.com
2000SS
IMPORTANT: Inquire with governing
authorities for local installation requirements.
NOTE: For Australia and New Zealand, line
strainers should be installed between the
upstream shutoff valve and the inlet of the
backflow preventer.
Limited Warranty: Ames Fire & Waterworks (the "Company") warrants each product to be free from defects in material and
workmanship under normal usage for a period of one year from the date of original shipment. In the event of such defects within
the warranty period, the Company will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH
RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty,
and the Company shall not be responsible for any incidental, special or consequential damages, including without limitation, lost
profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs
resulting from labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water
conditions, chemical, or any other circumstances over which the Company has no control. This warranty shall be invalidated by
any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation
of incidental or consequential damages. Therefore the above limitations may not apply to you. This Limited Warranty gives you
specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to
determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT
BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
A Division of Watts Water Technologies, Inc.
Its important that this device be tested
periodically in compliance with local codes,
but at least once per year or more as service
conditions warrant. If installed on a fire
sprinkler system, all mechanical checks,
such as alarm checks and backflow
preventers, should be flow tested and
inspected internally in accordance with NFPA
13 and NFPA 25.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SILVER BULLET 2000SS Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for AMES SILVER BULLET 2000SS Series

  • Page 1 • Service • Repair Kits Limited Warranty: Ames Fire & Waterworks (the “Company”) warrants each product to be free from defects in material and • Maintenance workmanship under normal usage for a period of one year from the date of original shipment. In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.
  • Page 2 Installation Instructions Please Read Prior to Installation: Vertical Installation ASSE Before installing any Ames assembly, Flush the Line thor- oughly to remove all debris, chips and other foreign objects. Failure to do so may make the assembly inoperable. The Ames 2000SS Backflow Preventers are approved by ASSE (American Society of Sanitation Engineers) to be installed in horizontal or vertical positions.
  • Page 3 #1 Cam-Check #2 Cam-Check DC Maintenance Instructions NOTE: Ames assemblies require minimum maintenance. All assembly from the 9 o'clock position to the 12 o'clock posi- assemblies must be retested once maintenance has been tion, then (without letting go of the access bar) push the performed.

Table of Contents