Table of Contents
Related Manuals for IMT Diamond air DA440HU
Summary of Contents for IMT Diamond air DA440HU
- Page 1 DA440HU: 99900782: 19990120 Model DA440HU Hydraulic Driven Underdeck Compressor IOWA MOLD TOOLING CO., INC. BOX 189, 500 HWY 18 WEST, GARNER, IA 50438 TEL: 515-923-3711 TECHNICAL SUPPORT FAX: 515-923-2424 MANUAL PART NUMBER 99900782...
- Page 2 DA440HU: 99900782: 19980224 PRECAUTIONS Read before operating your compressor! DANGER EXPLODING TANK WILL CAUSE DEATH, SERIOUS INJURY OR PROPERTY DAMAGE Drain air tank after each use to prevent moisture build-up and corrosion which leads to tank failure. Assure that tank and compressor relief valves work properly, and are at correct pressure settings.
-
Page 3: Table Of Contents
DA440HU: 99900782: 19980224 TABLE OF CONTENTS PARA TITLE PAGE Section 1. GENERAL INFORMATION 1-1. INTRODUCTION ....................1-1 1-2. ORDERING INFORMATION .................. 1-2 Section 2. INSTALLATION 2-1. GENERAL ......................2-1 2-2. PTO AND PUMP INSTALLATION ................2-1 2-2-1. PTO INSTALLATION ....................2-1 2-2-2. - Page 4 DA440HU: 99900782: 19980224 RECOMMENDED SPARE PARTS LIST 1 Year Supply DA440HU HYDRAULIC DRIVEN TOPDECK COMPRESSOR For Manual: 99900782 This spare parts list does not necessarily indicate that the items can be expected to fail in the course of a year. It is intended to provide the user with a stock of parts sufficient to keep the unit operating with minimal down-time waiting for parts.
-
Page 5: Section 1. General Information
DA440HU: 99900782: 19941223 SECTION 1. GENERAL INFORMATION 1-1. INTRODUCTION 1-2. ORDERING INFORMATION NOTE A NOTE IS USED TO EITHER CONVEY ADDITIONAL INFORMATION OR TO PROVIDE FURTHER EMPHASIS FOR A PREVIOUS POINT. CAUTION A CAUTION IS USED WHEN THERE IS THE STRONG POSSIBILITY OF DAMAGE TO THE EQUIPMENT OR PREMATURE EQUIPMENT FAILURE. - Page 6 DA440HU: 99900782: 19941223 NOTES...
-
Page 7: Section 2. Installation
DA440HU: 99900782: 19941223 SECTION 2. INSTALLATION 2-1. GENERAL CAUTION IT IS IMPORTANT THAT ROOM BE ALLOWED FOR FULL 2-2. PTO AND PUMP INSTALLATION ENGAGEMENT OF THE PTO. MODIFY THE EXHAUST OR OTHER OBSTRUCTIONS AS NEEDED. CAUTION AVOID SHARP BENDS IN THE SHIFTER CABLE. ALL BENDS SHOULD HAVE AT LEAST A 6"... -
Page 8: Pto Installation
DA440HU: 99900782: 19990120 WARNING 2-2-2. DRIVELINE AND PUMP THE INSTALLER OF THE DRIVELINE MUST INSPECT INSTALLATION THE FINAL POSITION OF THE DRIVELINE TO DETERMINE WHETHER ITS LOCATION PROVIDES SUFFICIENT PROTECTION TO AN OPERATOR, OR OTHER PERSONNEL, FROM HAZARDS ASSOCIATED WITH A ROTATING DRIVELINE. IF PROTECTION IS INSUFFICIENT, THE INSTALLATION OF A GUARD IS REQUIRED. -
Page 9: Underdeck Compressor Installation
DA440HU: 99900782: 19941223 2-3. UNDERDECK COMPRESSOR INSTALLATION FIGURE B-3. KILL SWITCH WIRING DIAGRAM... -
Page 10: Oil Cooler (Optional)
DA440HU: 99900782: 19941223 2-4. OIL COOLER (OPTIONAL) Oil coolers vary in their installation dependent on available space and other considerations. Install the oil cooler either in front of the carrier vehicle’s radiator or, as an alternative, in a protective structure which is cooled by an electric fan. -
Page 11: Section 3. Operation
DA440HU: 99900782: 19950719 SECTION 3. OPERATION 3-1. INTRODUCTION CAUTION 1000 RPM MAX. Operating this unit in excess of 1000 RPM, measured at the compressor flywheel, will void your warranty. Engine RPM may be different. 3-3. SYSTEM SHUTDOWN. 3-2. OPERATION CAUTION THE HYDRAULIC OIL TEMPERATURE MUST NOT BE ALLOWED TO EXCEED 190°F (88°C). - Page 12 DA440HU: 99900782: 19941223 NOTES...
-
Page 13: Section 4. Preventive Maintenance
DA440HU: 99900782: 19941223 Section 4. PREVENTIVE MAINTENANCE 4-3-2. HYDRAULIC FLUID 4-1. INTRODUCTION SPECIFICATIONS 4-2. LUBRICATION 4-3-3. HYDRAULIC FLUID DETERIORATION 4-3. HYDRAULIC SYSTEM 4-3-1. HYDRAULIC FLUID SELECTION FIGURE D-1. HYDRAULIC FLUID SPECIFICATIONS... -
Page 14: Hydraulic System Purging
DA440HU: 99900782: 19941223 NOTE BE THOROUGHLY FAMILIAR WITH THE FOLLOWING STEPS AND PREPARED TO PERFORM THEM IN AN UNINTERRUPTED SEQUENCE. IF THIS IS NOT DONE, EXCESSIVE OIL WASTE WILL OCCUR. CAUTION DO NOT ALLOW THE RESERVOIR LEVEL TO DROP BELOW 1/3 CAPACITY DURING THIS OPERATION. 4-3-5. -
Page 15: Preventive Maintenance Checklist
DA440HU: 99900782: 19941223 4-4. PREVENTIVE MAINTENANCE CHECKLIST FIGURE D-2. PREVENTIVE MAINTENANCE CHECKLIST... - Page 16 DA440HU: 99900783: 19941223...
-
Page 17: Section 5. Repair
DA440HU: 99900782: 19941223 SECTION 5. REPAIR 5-1. INTRODUCTION 5-3. DRIVE BELT 5-2. HYDRAULIC SYSTEM COMPONENTS FIGURE E-1. DRIVE BELT ADJUSTMENT... -
Page 18: Hydraulic System Troubleshooting Chart
DA440HU: 99900782: 19941223 FIGURE E-2. HYDRAULIC SYSTEM TROUBLESHOOTING CHART... -
Page 19: Section 6. Parts
DA440HU: 23000081.01.19971112 SECTION 6. PARTS 6-1. GENERAL ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 1. 52702376 BASE 24. 72053558 ADAPTER 3/4MPT 3/4MPT HEX 2. 70058486 BELT-POWER V 2B80 25. 72053604 TEE 3/4NPT 3. 70073051 COMPRESSOR (R30) 26. 72053713 ELBOW 3/4MPT 3/4FPT 90° SWVL 4. - Page 20 DA440HU: 23000081.02.19941223 FIGURE F-1A. DA440HU HYDRAULIC UNDERDECK COMPRESSOR (23000081-2)
-
Page 21: Section 7. Reference
DA440HU:99900782: 19941223 SECTION 7. REFERENCE FIGURE G-1. TORQUE DATA CHART... - Page 22 DA440HU:99900782: 19941223 FIGURE G-2. TIRE LOAD AND INFLATION PRESSURES...
- Page 23 DA440HU:99900782:...
- Page 24 DA440HU:99900782: LIMITED WARRANTY IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 TEL: 515-923-3711 TECHNICAL SUPPORT FAX: 515-923-2424...
Need help?
Do you have a question about the Diamond air DA440HU and is the answer not in the manual?
Questions and answers