Ingersoll-Rand SCHLAGE Stella Installation Instructions

Installation Instructions For All Models
Pack Contents
Main Fixtures
1 Internal handle x1
2 External pull x1
3 Lock body x1
4 Internal cylinder x1
5 External cylinder x1
6 Striker body x1
7 Striker cover x1
8 Locator template x1
9 Hole template x1
Screw Fixings
10 M4x50 taptite screw x2
M4x40 taptite screw x2
11 M4x20 c/s screw x2
12 No7x10 screw x2
13 No7x25 screw x2
14 M4x10 pozi screw x2
15 M3x8.0 pozi screw x2
Step 1 Door Preparation
Fixed door frame
front edge
Fixed door frame
Striker hole location
Striker hole location
front edge
Striker hole location
Internal and external
Internal and external
D
handle hole location
D
handle hole location
A
A
D
D
Cylinder tailbar hole
A Internal and external
Cylinder tailbar hole
A
location
D
handle hole location
location
B
A
B
D
A
B
Cylinder tailbar hole
B Striker hole location
Striker hole location
location
C
C
B
B
C
C
Striker hole location
C
E
C
E
E
E
E E
1 Remove hole template ➈ from installation
instructions.
2 Locate hole template ➈ onto fully closed internal
door. Dotted lines must line up with fixed door
frame front edge.
3 Mark holes A, B, C, D and E.
4 Drill holes A, B and C with 12mm drill. Drill holes
D and E with 3.5mm drill.
9
9
9
✂ 9
9
Template
9
Line up with fixed door frame front edge
Ingersoll-Rand Architectural Hardware Limited, PO Box 19-347, Avondale 1746, 437 Rosebank Road, Avondale 1026, Auckland, New Zealand
Phone 0800 477 869, Fax 0800 477 868, Customer Service Email nz_custserv@irco.com, Website www.ingersollrand.co.nz
Stella ™ Sliding Door Lock
2
2
2
5
2
2
5
5
2
5
14
8
8
8
8
8
8
Step 2 Cylinder Preparation For Locking
And Deadlocking Models Only
Fixed door frame
front edge
Fixed door frame
Fixed door frame
front edge
front edge
Fixed door frame Striker hole location
Striker hole location
front edge
Striker hole location
Internal and external
Internal and external
handle hole location
handle hole location
Internal and external
Cylinder tailbar hole
Cylinder tailbar hole
handle hole location
location
location
Cylinder tailbar hole
location
Striker hole location
Striker hole location
Striker hole location
Figure 1
Figure 1
Figure 1
Figure 1
Figure 1
Figure 1
Figure 1:
Internal handle rear view showing placement of internal cylinder
➀
screw fixing .
14
Figure 2:
External pull ➁ rear view showing placement of external cylinder
fixing .
14
Note: Cylinders can be handed for left or right opening doors.
1 Remove screw
14
2 Rotate and relocate cylinder according to handing and resecure with screw.
41mm
41mm
A
A
ø
12mm
ø
12mm
A
A
ø
A
A
ø
12mm
ø
3.5mm
ø
3.5mm
D
D
ø
ø
3.5mm
3.5mm
D
D
ø
83mm Internal Handle and External Pull Hole Centres
3.5mm
83mm
D
83mm
83mm
ø
3.5mm
83mm
D
83mm
14
14
5
14
14
5
14
3
3
10
11
11
11
11
11
11
14
14
14
10
11 10
10
11
11
10
10
11
11
1
1
10
11 1
1
1
1
1
2
2
1
2
1
14
14 14
14
14
5
14
14
4
4
4
4
Figure 2
4
Figure 2
4
Figure 2
Figure 2
Figure 2
Figure 2
and extract cylinder if necessary.
41mm
41mm
41mm 41mm
41mm 41mm
41mm 41mm
41mm 41mm
B C
B C
ø
12mm
ø
12mm
B
B C
ø ø
ø
12mm 12mm
12mm 12mm
B
ø ø
12mm 12mm
B
ø
12mm
83mm
83mm
83mm
Striker Hole Centres
6 15
15
6
6
7
6
6
7
7
6
7
7
7
13
3
10
3
10
3
4
10
4
10
4
3
4
4
10
4
14
14
14
1
1
1
Step 3 Cylinder Tailbar
Adjustment
2
2
2
2
2
2
2
14
2
2
5 14
14
14
5
5
14
5
Outside
5 Outside
Outside
Inside
Outside
Inside
Outside
Inside
Outside
Inside
C
and
➃
➄ and screw
1 Locate external pull
stile with cylinder tailbar showing through
to inside.
2 Mark and cut tailbar so it is flush with
internal stile.
ø
12mm
ø
12mm
C
ø
ø 12mm
12mm
C
ø
12mm
C
ø
12mm
ø
3.5mm
ø
3.5mm
E
E
ø
ø
3.5mm
3.5mm
E
E
ø
3.5mm
Line up with fixed door frame front edge
E
83mm
ø
3.5mm
83mm
E
83mm
15
13
15
13
15
13
13
12
13
15
12
13
12
12
12
13
13
12
13
13
15
13
15
15
15
15
12
12
12
15
12
12
12
Patent Pending
C
C
C
C
C
C
Inside
Inside
C
C
C
C
C
➁
onto outside of